A consolidated drained triaxial is conducted on a normally consolidated soil with chamber confining pressure of 152kPa. If the deviator stress failure is 250kPa, determine the following: a. Calculate the angle of friction of the soil (degrees) b. Calculate the shear stress at the failure plane (kPa) c. Calculate the normal stress at the failure plane (kPa)

A consolidated drained triaxial is conducted on a normally consolidated soil with chamber confining pressure of 152kPa. If the deviator stress failure is 250kPa, determine the following: a. Calculate the angle of friction of the soil (degrees) b. Calculate the shear stress at the failure plane (kPa) c. Calculate the normal stress at the failure plane (kPa)

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter12: Shear Strength Of Soil

Section: Chapter Questions

Problem 12.18P

See similar textbooks

Similar questions

A consolidated drained tri-axial test was conducted on a normally consolidated clay. The results were as follows: 03 = 300 kPa (confining pressure) Deviators stress = 300 kPa 0 Compute the angle of shearing resistance. Compute the angle that the failure plane makes with the major principal. stress. Compute the shear stress on the failure plane.
A triaxial shear test was performed on a well-drained sand sample. The normal stress on the failure plane and the shear stress on the failure plane, at failure were determined to be 6100 psf and 4600 psf, respectively. a. Determine the angle of internal friction of the sand? b. Determine the angle of the failure plane? c. Determine the maximum principal stress? Please answer this asap. For upvote. Thank you very much
A consolidated drained tri-axial test was conducted on a normally consolidated clay. The results are as follows: Chamber confining presssure = 138 kPa Deviator stress = 258 kPa a. Compute the friction angle of the soil b. Compute the normal stress at failure c. Compute the shear stress at failure
2. A triaxial shear test was performed on a well-drained sand sample. The normal stress on the failure plane and the shear stress on the failure plane, at failure was determined to be 6,300 psf and 4,200 psf, respectively. a. Determine the angle of internal friction of the sand. b. Determine the angle of failure plane. c. Determine the maximum principal stress.
A consolidated drained tri-axial test was conducted on a normally consolidated clay. The results as follows: Chamber confining pressure: 138 kPa Deviator Stress = 258 kPa Determine the normal stress at failure in kPa.
9. A consolidated drained test was carried out on a sandy clay under a cell pressure of 250 kPa. A constant back pressure of 120 kPa applied throughout the test. The dimensions of the sample were 76 mm x 38 mm. Addional test data recorded at failure were: Load transducer force = 368 N 3 Measured change in volume = 2.42 x 10 m³ Axial deformation = 2.05 mm Determine the major principal stress, o, at failure. (455 kPa)
Answer any one asap 1.A triaxial test is performed on a normally consolidated clay. The sample is further consolidated by the test of all-around confining pressure prior to the application of the axial load. The axial force is applied very slowly. The equipment pore pressure lines remain open so that drainage of the soil pore water can occur during the test. The sample fails when minor principal stress is 49 kPa and the major principal stress is 91 kPa. Determine the angle of internal friction with no decimal places. 2.A dry sand sample was tested in direct shear and yielded a shear strength of 132 kPa under a normal stress of 215 kPa. Lab results indicate the soil's wet unit weight is 18.1 kN/m3 and the saturated unit weight is 20.2 kN/m3. Determine the shear strength, in kPa, within the native sand deposit at a depth of 2.5 m below the water table. The water table is 3 m below ground surface. Provide your answer with 2 decimal places, do not include the units and assume a unit…
a consolidated tri-axial test was conducted on a normally consolidated clay. the results were as follows: chamber confining pressure = 316 kPa, deviator stress = 424 kPa. compute for the shear stress on the failure plane in kPa.
Give the correct option In a drained triaxial test on consolidated clay the stress and angle are as follows: Deviator stress is 20 lb/in2 and friction angle is 21°. Calculate the effective confining pressure at failure?a) 21 lb/in2 b) 22.2 lb/in2 c) 25.4 lb/in 2 d) 17.9 lb/in2
A sand sample is subjected to direct shear testing. Two tests areperformed. For test 1, The sample shears at a stress of 2500 psf whenthe normal stress is 4000 psf.Test 2, The sample shears at a stress of 3500 psf when the normalstress is 6000 psf. Determine the following:a) Angle of Internal frictionb) Value of cohesionc) Compute the shear stress at a depth of 12 ft. if the unit weight ofthe soil is 150 pcf
A consolidated-undrained triaxial test was conducted on a saturated, normally consolidated clay. The test results areσ3 = 13 lb/in2σ1(failure) = 32 lb/in2Pore pressure at failure = u = 5.5 lb/in2. Determine c, Φ, c', and Φ'.
A cohesionless soil sample is subjected to a triaxial test. The critical state friction angle of the soil is 28 degrees and the normal effective at the failure is 200 kPa. Determine the critical state shear stress. Determine the plunger stress. Determine the cell pressure.