A dog is pulling on his lead at an angle of 39 degrees with a force of 50 Newtons. What is the force downward? Newtons. What is the force horizontally? Newtons. Note: You can type the trig in the answer box for all these problems. For example if the answer is 50cos(10), you can just type that into the answer box. To get inverse trig functions type arcsin, arccos or arctan.

A dog is pulling on his lead at an angle of 39 degrees with a force of 50 Newtons. What is the force downward? Newtons. What is the force horizontally? Newtons. Note: You can type the trig in the answer box for all these problems. For example if the answer is 50cos(10), you can just type that into the answer box. To get inverse trig functions type arcsin, arccos or arctan.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Using the graphical method, find the sum of the vectors in each number. Draw your vectors on a separate sheet of paper. Scale 10 units: 1cm 1. A box was pushed with a force of 20 Newtons to the right and 40 Newtons to the left. What is the sum of these vectors?
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
Question 3) On the plate in the figure, the length L is given as L=72 m . According to this; Question 3-A) Find the X coordinate of the geometric center of the plate . ( Enter your result without writing m units. Write at least three digits after the comma.) Question 3-B) Find the Y coordinate of the geometric center of the plate . (Your result m in size Enter the writing unit. Enter the form of at least three digits after comma.)
Solve the following question
52 What is the distance between the center of circle A and the corner at B? R3 03 Start a new drawing based on Mech-Millimeters.dwt. Draw the object shown in Figure A-1, starting with the center of the Ø3 circle at point 5,5. Draw only the object, not the dimensions and then answer the following questions: O 186794 198628 193132 171870 R1.0 TYP. 18 8 2 2 1 10
A person starts walking from home and walks: 2 miles East 7 miles Southeast 6 miles South 6 miles Southwest 2 miles East This person has walked a total of miles Find the total displacement vector for this walk: If this person walked straight home, they'd have to walk miles Round your answer to at least one decimal place if needed.
Using graphical method solve this problem: Suppose you first walk A in a direction of B west of north then C in a direction D south of west. You rest for 20 minutes and started to compute the distance you traveled. Take A, B, C and D found in the table below. (You may use scale such as 1cm = 2m in your drawing) C. What is the angle between AC ? D. What is the angle between your first walk A to the resultant R?
Question 3) On the plate in the figure, the length L is given as L = 18 m . According to this; y 2L L 2L 3 L -- L Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result as m without writing units.) Response: Question 3-B) Find the Y coordinate of the geometric center of the plate . (Enter your result as m without writing units.) Response:
JUST DRAW THE SCHEMATIC DIAGRAM. NO NEED TO SOLVE. THANK YOU In Rizal province, one of its power plants has been thoroughly monitored for possible conversion into a wind power plant. A propeller wind turbine is to be used. Survey showed that Rizal Province at a height of 10 meters above the ground has a minimum wind speed of 7.1 miles per hour duringthe month of June and a maximum wind speed of 12.9 miles per hour during the month of January. The minimum temperature is at 75 degree Fahrenheit during the month of January and maximum temperature is at 89 degree Fahrenheit during the month of May. The existing power plant has an output of 54MW. For the proposed wind power, the power coefficient of turbine is 35% and the generator efficiency is 95%. Theimpeller diameter is assumed not to exceed 90m. Determine the following:a. Theoretical Wind Power Outputb. Electrical Power Outputc. Number of turbines to be installed
Answer and solve the following problem.
GIVEN : W= 345 N Q°= 27 DEGREE R°= 50 DEGREE S°= 25 DEGREE SOLVE (a) AC= IN NEWTON SOLVE (b) BC= IN NEWTON SOLVE (c) CD= IN NEWTON PLS PLS SHOWS THE COMPLETE SOLUTION AND WRITES LEGIBLY AND ALSO INCLUDES THE FREE-BODY DIAGRAM. WRITE IN FOUR DECIMAL PLACES.
Please solve question 16-109 below this in the follwoing way: Please include a kinamatic diagram (one for velocity and one for acceleration). Please DO NOT solve this using velocity analysis (cartesian vector analysis). I would like it to be solved using scalar method. We dont use 3D in this course. We only use scalar analysis for the relative velocity equation (writing the x and y components of the equation and solving the equations for the unknowns). I have attached a sample question with solution in order to get an idea on how to use the scalar method to solve my question. I would like question 16-109 to be solved in a similar way. Thank you for your understanding. If you can solve it as soon as possible that would be great and I will give you a thumps up and positive feedback :)