A fertilizer solution with 0.1M Na+ and 0.05M Ca2+ is applied over a long period of time to a soil. The soil is then irrigated and the leachate has a 0.05M Na+ concentration. What is the Ca2+ concentration in the leachate if the ratio of Na to Ca on the solid is unchanged? g. Relate irrigation to: i. Soil salinity. ii. Soil sodicity.

Q: when analyzing the stability of an entire frame structure. How would one proceed with the analysis…

A: Given question: i. How to proceed the analysis of a framed structure to check the stability ? ii.…

Q: Theories of Failures Q.24 A point in a solid shaft under action of bending moment and twisting…

A: Given data- Principal stresses- σ1=80 N/mm2 (tensile),σ2=30 N/mm2 (compressive), Yield strength-…

Q: Beam subjected to moving distributed load of 4 kN/m. Maximum shear force that can occur just to…

A:

Q: *If the required weight of coarse aggregate for mix design is 2000 lbs per cubic yard of PCC,…

A: Reference : ACI 318 mix design code Given : Weight of coarse aggregate Specific gravity To determine…

Q: 5. A capture well is pumping at a rate of 152,000 ft³/day. The confined aquifer has a thickness of…

A: Given: Pumping rate, Q = 152000 ft3/day Aquifer thickness, b = 102 ft hydraulic conductivity, K =…

Q: Problem 8.1. On a given day, the following meteorological and surface measurements were collected at…

A: On a given day, the following meteorological and surface measurements were collected at noon from a…

Q: AT section has the dimensions given in Fig. ..Show that the neutral axis is 3 inches below the top…

A: Given data : INA = 166.7 in.4 Tensile stress at the bottom of the flange = 1000 psi This is a…

Q: What is the difference between three-moment equation and moment distribution methods if applied to…

A: What is the difference between three-moment equation and moment distribution methods if applied to…

Q: Water flows through a sand filter. The soil mass's cross-sectional area and length are 2900 cm² and…

A:

Q: Based on the following data from an industrial wastewater treatment plant as a part of designing the…

A: We have to calculate the volme of equalization,

Q: Example 1: A flow of water from a reservoir to a pipe of different diameters shown in Figure below.…

A:

Q: Question- For steady state flow to a fully penetrating well in a confined aquifer, the drawdown at…

A: Given data- Steady-state flow- Drawdown- S1=4.92 m, S2=5.45 m, Radial distance- r1=1.56 m, r2=1.80…

Q: 10 cm diameter solid cylinder of height 10 cm and weighing 0.40 kg is immersed in a liquid (800…

A:

Q: Group C: Design a concrete mix to implement a Mass concrete (exposed to sever conditions moisture…

A: Given: Design compressive strength = 25 MPa Standard deviation = 4 Cement = sulphate resisting…

Q: in 12 in 5 in

A: To find centroid and total area

Q: A cable of span 120 m and dip 10 m carries a load of 6 kN/m of horizontal span. The maximum tension…

A: Given data in question  Load 6 kN/m Span 120 m Dip 10 m To find out  Maximum tension in cable

Q: A T- beam section shown in the figure below. f'c-28 Mpa, fy-420 Mpa. Calculate the design moment…

A: Answer  We are given width of flange bf = 800 mm thickness of flange tf = 100 mm thickness of web tw…

Q: : The T-beams sections shown in the figures below. f'c-28 Mpa, fy=420 Mpa. Calculate the design…

A:

Q: of ree offe free to freedom, and; of frus's Explain the concept termine the feed om for the…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: thick The average effective overburden pressure on 0 m homogeneous saturated clay layer is 150 kPa.…

A:

Q: 14.2 Identify the type of bond patterns in the following 2 masonry walls. WALL 1 WALL 2 MO

A:

Q: Determine the reactions at the supports.

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: 1. Solve the given beam A 1.5 k/ft 6 ft- B 30 k с El = constant E= 1,500 ksi 1=20,000 in.4 5f1- a.…

A: Since the problem was asked to solve in four methodologies. The first methodology is used to solve…

Q: An I-beam having a cross section shown below, determine the y from the x-axis shown. Calculate the…

A: Given  d= 330 mm  tf1= 10 mm  tf2= 11 mm  b1= 220 mm  b2= 240 mm  tw= 9 mm

Q: Q- For a culturable command area of 1000 hectares with intensity of irrigation of 70%, the duty on…

A: Given- CCA=1000 ha, Intensity of irrigation I=70%, Duty D=1500 ha/cumec, Losses=25%,

Q: : Design the T-Beam section shown in fig. f'c=24 Mpa, fy=414 Mpa. L.L = 21 kN/m D.L=12 kN/m 3 m 450…

A:

Q: A cylindrical tank contains water at a height open cylindrical tank containing cleaning fluid…

A:

Q: Find the missing rainfall (in mm) at station X. (given data are in mm) Rain gauge Normal Actual A…

A:

Q: a) Consider the structure below where A is fixed and B is pinned. W P- A B i) State if the structure…

A: Given: A frame with loading  Required: To find structure is stable or unstable, determinate or…

Q: sketch the NFD, SFD, BMD, and deformed shape

A: A frame is given with roller support at A and fixed support at D. A hinge is also present at C. The…

Q: 1. Taking soil samples and testing the soil properties takes an engineer an average of 35.5 days per…

A: Given data, Average expected time to execute(TE )= 35.5 days  Standard deviation = 1.9 days  For…

Q: Problem 11.6 - Determine the moments of inertia of the standard rolled-steel angle section with…

A:

Q: Answer the following by True or False (Note: each one wrong answer will cancel one right answer).…

A: This question is related to the Soil Mechanics from Civil Engineering. This is True false based…

Q: H.W 13. A cylindrical vessel of radius ro filled with water to height h is rotated around the…

A:

Q: Find

A:

Q: 13-45 Water is flowing uniformly in a finished-concrete channel of trapezoidal cross section with a…

A:

Q: Determine the RL of the top of a transmission tower from the following observations. Also determine…

A:

Q: A rectangular footing 1 m x 2 m is placed at a depth of 2 m in a saturated clay behaving an…

A: Given- Rectangular footing size 1 m×2 m, Depth=2 m, UCS=100 kN/m2, It is needed to find the net…

Q: A mechanism is shown below. The number of tertiary links and the DOF, respectively are:

A: A ) To Find : Degree of freedom ? A problem of Structural Analysis.

Q: Q1/ If the length of the square is (20m) and the scale is (1:500), Find: 1- The number of contour…

A: To find the number of contours in the given block and to draw the contours using calculations.…

Q: 5. In Correction in Taping what are the four Rules that we apply?

A:

Q: 30 cm well completely penetrates an artesian aquifer. The length of the strainer is 25 m. Determine…

A:

Q: 7. Will the soil represented by the solid line serve as a suitable filter for the soil represented…

A: To Determine :- Can the soil represented by the solid line serve as a suitable filter for the soil…

Q: Column A B carries a centric load P of magnitude 12 kips. Cables B C and BD are taut and prevent…

A: First we summarise the given data : P = 12 kips E = 29 X 106 psi FOS = 2.9 To Find : Determine the…

Q: : The T- beams sections shown in the figures below. f'c-28 Mpa, fy-420 Mpa. Calculate the design…

A:

Q: 4) What is the Error per angle and Error of closure based on the below sketch for the loop traverse?

A:

Q: operating under steady state in a confined aquifer of 35 m thickness is 2000 lpm. Values of drawdown…

A:

Q: 60N 10 3m 40° 150N A 90N SON P 3. Which of the following single forces is equivalent to the given…

A:

Q: Determine the reaction forces in the fixed support at A, the pin supports at B and D and the roller…

A:

Q: 6 7 8 9 10 11 12 13 14 15. 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33. 34 35 36 37 A…

A:

Sediment transport

Sediment transport or Soil transport is the movement of solid particles, usually due to the combination of gravitational forces acting on the sediment, and the movement of the liquid at which the sediment enters. Soil erosion occurs in natural systems where the particles are sandstones (sand, rocks), mud, or clay; the liquid is air, water, or ice; and the gravitational force that works to move particles to the landing surface. Sediment transportation or soil migration due to the movement of liquids occurs in rivers, lakes, lakes, oceans, and other bodies of water as a result of currents and waves. Transportation is also caused by glaciers as they flow, and to places on earth under the influence of wind. Soil erosion due to gravity alone is possible in most sloping areas, including hills, scarves, cliffs, and the continental shelf — the continental boundary of the slope.