A gas initially at p₁ = 827, 400 Paa and v₁ = 2.6 li undergoes a process and change state to a point where p2 = 275, 800 Paa and V₂ = 6.2 li. If the internal energy decrease 123 KJ and cp = 295. determine (a) c,, (b) AH and (c) R.

A gas initially at p₁ = 827, 400 Paa and v₁ = 2.6 li undergoes a process and change state to a point where p2 = 275, 800 Paa and V₂ = 6.2 li. If the internal energy decrease 123 KJ and cp = 295. determine (a) c,, (b) AH and (c) R.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2.2.8. A closed tank contains a liquid (S. G.= 0.85) under pressure. The pressure gauge, depicted in…

A: In this problem, we will calculate the pressure at the bottom of the tank as well as the height of…

Q: When you step on the brakes, you are compressing a narrow piston (radius 2 cm), creating pressure in…

Q: The cross section of a bar made of cartridge brass is a hexagon. Find dimension a if the allowable…

Q: The velocity of a particle moving in the x-y plane is given by (5.00i + 7.38j) m/s at time t = 3.87…

Q: The temperature of a gas undergoing a continuous throttling process _______ across the throttling…

A: This question is based on the concept of throttling process and inversion curve.

Q: 1. A steam power plant operates on a reheat regenerative Rankine cycle with a closed feedwater…

A: Given: The inlet temperature to the turbine 1, T1 = 500 C The inlet pressure to the turbine 1, P1 =…

Q: A CSP supercritical steam power plant using a concentrating collector arrayfor DSG (refer to Figure…

A: As per the rule, only the first three sub-parts will be answered Plant output power is Pe=28 MW The…

Q: Draw the axial force and shear force and bending moment digram of frame

A: Given: The uniformly distributed load: →w=2k/ft From the symmetry, the vertical reaction at point a…

Q: The barometric pressure at sea level is 760 mm of mercury while that on a mountain op 35 mm. if the…

A: Given:barometric pressure at sea level, Po=760 mm Hgpressure on mountain top, P=735 mm Hgdensity of…

Q: A five-foot steel shaft (G=11,500 ksi) is partially hollowed out and filled with a brass core…

Q: A solid 20-mm-diameter shaft is subjected to an axial load P. The shaft is made of aluminum [E = 70…

A: Given: Shaft diameter is 20 mm E= 70 GPa and v = 0.33 Required: strain and axial force

Q: In the figure below, a ball is thrown up onto a roof, landing 4.14 s later at height h = 24.5 m…

A: (a) To find: The horizontal distance. Given: The height is h=24.5 m. The landing time is t=4.14 s.…

Q: 18. Work is done by a substance in reversible nonflow manner during which 32 KJ are added, the…

Q: Derive the four 1st-order ODE equations of the system and the formula of the Forward Euler method.

A: Given: To find: 1st order ODE

Q: Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal…

Q: For a given part drawing (fig.2) prepares a part program for a wire electric discharge machine using…

A: For the given part drawing, we can write part program using Fanuc cut language which is based on G…

Q: Calculate the moment of inertia of the shaded area about the x-axis. Assume a 35 mm, r - 25 mm.…

A: Givena=35mmr=25mm

Q: Parallelogram law of forces formula derivation detailed

A: Parallelogram's lawThe parallelogram rule states that if we place two vectors so they have the same…

Q: If we have a second order accurate centred scheme for approximating a first order derivative du/dx,…

A: Given: Second order accurate centered scheme dudx=ux+dx-ux-dx2dx+Odx2 Phase error = 3% To find:…

Q: Determine the force in member EF of the loaded symmetrical truss. Assume no horizontal reactions at…

A: Solution: Given Data: Horizontal reaction forces at A and C are zero. To Find: The force in the…

Q: Air from a workspace enters an air conditioner unit at 30oC dry bulb and 20oC wet bulb.The air…

Q: 17. A piston-cylinder arrangement contains a gas at P1 = 600 KPa, V₁=0.10 m³ and expand to V2= 0.5…

Q: It is suggested that an incompressible fluid flows with the velocity field v = (sin (xy²zt), x²t,…

A: Given: v=sinxy2zt,x2t,zy2t To find: Determine expressions for flow divergence Explain in a few…

Q: A steel plate having a thickness of 100 mm is suddenly exposed to a hot gas at 1000 oC in a furnace.…

Q: LIN a) In a concentric-pipe heat exchanger, one of the fluids is a condensing vapour and the other…

A: This question is based on the concept of Heat exchanger.

Q: A rectangular gate, shown in Fig. Q5b forms a wall of a tank which holds water to a depth of 2m. The…

A: Givend=2mw=3m

Q: Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground…

A: Givenw=236lb

Q: Explain the features of port and direct injectors and the different testing methods without removing…

A: Port injectors and direct injectors are two types of fuel injectors used in internal combustion…

Q: 1. Calculate the strain in a 42 in. long copper wire that stretches 0.035 in. [unitless, decimal…

A: The given data Original length of wire lo= 42 in The stretch in wire (lf -lo) = 0.035 in Find the…

Q: Air enters a compressor operating at steady state at 1 atm with a specific enthalpy of 297 kJ/kg and…

A: Given data:- Specific enthalpy at inlet (h1)= 297 kJ/kg specific enthalpy at outlet (h2) =1030…

Q: A rod of mass 0.9 kg/m is welded to a hollow disc of mass 3 kg/m² as shown. Determine the mass…

Q: ad is described by the function here the boldface type indicates that G is a vector. a) Draw an FBD…

Q: For a certain gas, R = 0.277 kJ/kgm K and k = 1.384. (a) What are the value of cpand Cv? (b) What…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: (a) Derive an expression for the air standard efficiency of a Brayton cycle in terms of pressure…

A: The derivation of the air standard efficiency is given below step by step.

Q: 3. The rigid tank contains a superheated water vapor that is initially at P₁ and T₁. The system is…

A: For solution refer below images. given that, state 1- super heated steam state 2 - with constant…

Q: 6. A fluid at a pressure of 3 bar and specific volume of 0.18 m³/kgm contained in a piston cylinder…

Q: The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in…

Q: An ideal Rankine cycle operates between the pressure limits of 15,000 kPa in the boiler and 15 kPa…

Q: wo metallic rods are connect in parallel to heat reservoirs held at T1 and T2, respectively. One rod…

Q: An electric wire having a diameter of 1.5 mm and covered with a plastic insulation (thickness = 2.5…

A: In this problem, we will calculate the critical radius, heat loss without insulation, and heat loss…

Q: Water flows at a rate of 0.030 m³/s in a 0.16-m-diameter pipe that contains a sudden contraction to…

A: Flow rate of Flow Q = 0.030 m3/s Diameter of pipe at entrance d1= 0.16 m Diamete of pipe at…

Q: The molar analysis of a gas mixture at 25°C, 90 kPa is 40% N₂, 40% CO2, and 20% O2. Step 1 ✓ Your…

Q: The sprinter begins from rest at position A and accelerates along the track. If the stationary…

Q: The motion of the 5.00-kg uniform rod AB is guided by small wheels of negligible mass that roll on…

A: Given: The mass of the rod, m = 5 kg The spring constant, k = 430 N/m The initial position of the…

Q: in fig below, fluid A is water (PH2o = 62.1lbm/ft^3), fluid B is mercury (PHg = 0.4888lbm/in^3).…

A: GivenρH2O=62.1 lbm/ft3ρhg=0.4888 lb/in3=0.4888×123 lb/ft3=844.6464 lb/ft3z=4.5 ft

Q: Solve for required parameters using the figure above. The figure is not in scale, redraw if possible…

Q: 1. Steam in the condenser of a power plant is to be condensed at a temperature of 30°C with cooling…

Q: 20) A horizontal force P = 1200 lb is applied to the rectangular bar as shown. The dimensions d =…

A: Given data P=1200(lb) d=1.50in, b=2.50in and e= 2.00in Find the normal and shear stress at point H

Q: A simple ideal Rankine Cycle operates between the pressure limits of 6969 kPa and 69 kPa. If the…

A: Given data:- A simple ideal Rankine Cycle high pressure (boiler pressure)= 6969 kPa low…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

p62,#13 with illustration and explanation

X 13. A gas initially at p₁ = 827, 400 Paa and v₁ = 2.6 li undergoes a process and
change state to a point where p2 = 275, 800 Paa and V₂ = 6.2 li. If the internal
energy decrease 123 KJ and cp = 295 determine (a) c,, (b) AH and (c) R.
kgm-K

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1 m3 of air is heated reversibly at constant pressure from 15°C to 350°C, and is then cooled reversibly at constant volume back to the initial temperature. The initial pressure is 1.03 bar. Take Cp, Çx and R as 1.005 kJ/kg,K , 0.718 kJ/kg. K and 0.287 kJ/kg,K respectively. 1. a) Sketch the processes on a T-s diagram. b) Calculate (i) the net heat flow, and (ii) the overall change of entropy.
One-quarter lbmol of oxygen gas (O2) undergoes a process from p1 = 20 lbf/in2, T1 = 500oR to p2 = 150 lbf/in2. For the process W = -500 Btu and Q = -202.5 Btu. Assume the oxygen behaves as an ideal gas. Determine T2, in oR, and the change in entropy, in Btu/oR.
3. Air is contained within a piston-cylinder assembly The cross sectional area of the piston is 0.01 m². Initially the piston is at 1 bar and 25°C, 10 cm above the base of the cylinder. In this state, the spring exerts no force on the piston. The system is then reversibly heated to 100°C. As the spring is compressed, it exerts a force on the piston according to: F=-kx where k= 50,000 N/m and x is the displacement length from its uncompressed position. Determine the work done. a. -166 J b. -216 J c. 166 J d. 216 J
4. A mass of 0.05 kg of carbon dioxide (molar mass 44 kg/kmol), occupying a volume of 0.03 m³ at 1.025 bar, is compressed reversibly until the pressure is 6.15bar. Calculate the final temperature, the work done on the CO2, and the heat supplied: i) 1.4 = constant when the process is according to a law pv ii) when the process is isothermal iii) when the process takes place in a perfectly thermally insulated cylinder. Use Cp of CO2 as 939 J/kgK, which is the cp at 400K as per tables of properties page 17.
From a state defined by 285.3 psig, 100ft3 and 240F, helium (R=386.04 ft-lbf/lbm-R, k=1.666) undergoes an isentropic process to 0.3psig. What is the Final temperature (R)
Water contained in a closed, rigid tank, initially at 100 lbę/in?, 800°F, is cooled to a final state where the pressure is 40 Ib;/in?. Determine the quality at the final state and the change in specific entropy, in Btu/lb•°R, for the process.
One-quarter Ibmol of oxygen gas (O2) undergoes a process from P1 = 20 lbf/in?, T1 = 500°R to p2 = 150 lbę/in2. For the process W = -500 Btu and Q = -177.5 Btu. Assume the oxygen behaves as an ideal gas. Determine T2, in °R, and the change in entropy, in Btu/°R.
2. The work required to compress a gas reversibly according to pV130 = C is 67,790 J, if there is no flow. Determine AU (in kJ) and Q (in kJ) if the gas is methane. For methane, k = 1.321, R = 518.45 J/kg-K, cv = 1.6187, cp = 2.1377 J/kg-K please draw the P-V and T-S diagrams
11. an ideal gas with MW= 33 is contained in a flexible tank. it is heated from 258.71 C to 559.35 C. if the change in internal energy is 178 kJ/kg, what is work in kJ/kg
One-quarter Ibmol of oxygen gas (O₂) undergoes a process from p₁ = 20 lb/in², T₁ = 500°R to p₂ = 150 lb/in². For the process W= -500 Btu and Q = -140.0 Btu. Assume the oxygen behaves as an ideal gas. Determine T2, in "R, and the change in entropy. in Btu/°R. Step 1 Determine T₂, in °R. Your answer is correct. T₂- 78862 Hint Step 2 * Your answer is incorrect. A$12 Determine the change in entropy, in Btu/°R. °R i 0.1968 eTextbook and Media Btu/ºR Attempts: 1 of 4 used
Can you show the step-by-step solution how to get the answers for this problem? There are 2.27 kg/min of steam undergoing an isothermal process from 27.6 bar, 320 °C to 6.9 bar. Sketch the pV diagram and Ts diagram and determine delta s, Q, delta H, Work nonflow, delta U, and delta V
2. Water is heated in a boiler tube at steady state from an inlet state of 500 kPa 25 deg-C (State-1) to an exit state of 500 kPa, 500 deg-C (State-4). Neglect changes in ke and pe, and use the PC model to answer these questions. If the mass flow rate of water is 5 kg/s Hide Details (a). Determine the rate of heat transfer in kW KW Enter answer as a decimal number (3.14, 5.0, -2.78, 5, for example) (b) What percent of the heat transfer is used to to boil the water from saturated liquid to saturated vapor state? Enter answer as a decimal number (3.14, 5.0, -2.78, 5, for example) (c) What percent of the heat transfer is used to heat up water to saturated liquid state? Enter answer as a decimal number (3.14, 5.0, -278, 5, for example)