A gravity dam is a solid concrete structure, which is designed to safely stand against the precalculated volume of water. Consider a gravity dam such that W_ABCE is 1.800 kN and W_CDE is 0.675 kN. Assuming that the force exerted by the water perpendicular to the vertical face of the dam AB is P, acting h meters from B, and the coefficients of non-sliding and sliding friction between the dam and the horizontal platform are 0.500 and 0.300 respectively, A D B 0.200 m 0.1500 m

A gravity dam is a solid concrete structure, which is designed to safely stand against the precalculated volume of water. Consider a gravity dam such that W_ABCE is 1.800 kN and W_CDE is 0.675 kN. Assuming that the force exerted by the water perpendicular to the vertical face of the dam AB is P, acting h meters from B, and the coefficients of non-sliding and sliding friction between the dam and the horizontal platform are 0.500 and 0.300 respectively, A D B 0.200 m 0.1500 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular gate 6 ft tall and 5 ft wide in the side of an open tank is held in place by the force F as indicated in the figure. The weight of the gate is negligible, and the hinge at O is frictionless. (a) Determine the water depth, h, if the resultant hydrostatic force of the water acts 2.5 ft above the bottom of the gate, i.e., it is collinear with the applied force F. (b) For the depth of part (a), determine the magnitude of the resultant hydrostatic force. (c) Determine the force that the hinge puts on the gate under the above conditions. Hinge O Gate F 2.5 ft 6 ft Water
The cross section of a concrete dam JKLMN as shown in Figure 1 is used to retain water. The specific weight of the concrete dam is 24 kN/m. The coefficient of friction between the base of the dam and the foundation is 0.45. For one meter dam length, calculate the maximum water depth, d to ensure the stability of the dam against; (a) Sliding. (b) Overtuning. 3 m L. M 3.3 m Wi d. F- P I W2 10 m K 4 m Figure 1 CS Scanned with CamScanner
The face of a vertical dam has the shape of an isosceles trapezoid of altitude 11 ft, upper base 28 ft, and the lower base 20 ft. Find the total force exerted by the water on the dam when the water is 8 ft deep. :use fluid force formula
The masonry dam shown in the figure is subjected to water pressure at upstream side. It is built on a rock foundation. It is made of masonry having a weight of 150 pounds per cubic foot. The intensity of hydrostatic pressure at the base varies uniformly from 20% of the full hydrostatic pressure at the heel to zero at the toe. Calculate the minimum width "b" of the base such that no tension will occur at the base. Hint: so that no tension will occur at the base, the resultant reaction must act at one third of the base. Round off your answer into one decimal place. Answer: b = 9m 2m 1m H m b
Situation 1 - A small dam of height h = 2.2 m is constructed of vertical wood beams of thickness t = 120 mm, as shown in Figure S01-0321. Consider the beams to be simply supported at the top and bottom. Assuming that the weight density of water is 9.81 kN/m³. m 2.1 17. Determine the maximum shearing stress in the beam in MPa. A. 0.198 C. 0.147 B. 0.256 D. 0.321 18. Determine the maximum bending stress in the beam in MPa. A. 3.214 C. 2.792 B. 2.248 D. 2.587 TE h B Figure S01-0321
Hydrostatic forces on inclined plane surface 6Q. A rectangular gate having a width of 4 ft is located in the sloping side of a tank as shown in the figure. The gate is hinged along its top edge and is held in position by the force P. Neglect the friction at the hinge and weight of the gate. Determine the required value of P. V Water Hinge Gate 60° 6 ft 10 ft
SITUATION 32 The simply supported beam in the figure below has a rectangular cross section 120 mm wide and 200 mm high. a. Compute the maximum bending stress in the beam. a. Compute the bending stress at a point on section B that is 25 mm below the top of the beam. 0.8 m RA 6 kN/m B 2m NA с 120 mm 15 kN D A 100 mm -+ 100 mm 1.0 m E RE
Please answer with a complete solution. Thank you! The forces acting on a 1-ft length of a dam are shown. The upward ground reaction varies uniformly from an intensity of pA (lb/ft) at A to pB (lb/ft) at B. Determine pA and pB and also the horizontal resistance to sliding H.
The height of the reinforced concrete water dam in the figure is L width a. The unit weight of the body of the dam Su gola Betogarme su bendi is y=24 kN/m'. Since the height of the water lake is h and the lateral water thrust to the body is H=5h? kN/m, determine the maximum water height (hmax) to avoid 4. tensile stress at the base of the dam. (L=15m, a=7m) Note: Calculate for unit height (taking 1 m),
Determine the vertical distance of the center of gravity of the curved gate from the water surface shown in the figure. The curved gate is 5.7 m long. The values of the vertical component (Fv) and the resultant force. (F) acting on the gate are 300 kN and 400 kN asap
From the given figure. Determine the total active lateral pressure at the interface in kPa.
2.12. Find hydrostatic force on the conical body shown in figure below. (H =2.7m, L₁ L2=0.6m, R=0.9m) H₂O H L₁ L2 R