A homeowner uses a snowblower to clear his driveway. Knowing that the snow is discharged at an average angle of 36° with the horizontal, the initial velocity Vo of the snow =m/s. For h=5.53 m and R=21.96m.B0.6 mSelect one:O a. 18.1O b. 29.3О с. 14.1O d. 9.4O e. 23.9Time of maximum heightSelect one:O a. 0.56O b. 0.85Ос. 1.09O d. 1.43O e. 1.76Maximum height from the ground(m)Select one:O a. 2.0O b. 11.3О с. 3.1O d. 4.0O e. 6.4

Given, Initial height = y0 = 0.6 m Angle of projection = α = 36o Final height = h = 5.53 m Range = R…

A homeowner uses a snowblower to clear his driveway. Knowing that the snow is discharged at an average angle of 36° with the horizontal, the initial velocity Vo of the snow = m/s. For h=5.53 m and R=21.96 m. 0.6 m .R Select one: O a. 18.1 Ob. 29.3 O. 14.1 Od. 9.4 O e. 23.9 Time of maximum height Select one: O a. 0.56 Ob. 0.85 Oc. 1.09 Od. 1.43 O e. 1.76 Maximum height from the ground (m) Select one: O a. 2.0 Ob. 11.3 O. 3.1 Od. 4.0 Oe. 6.4

A homeowner uses a snowblower to clear his driveway. Knowing that the snow is discharged at an average angle of 36° with the horizontal, the initial velocity Vo of the snow = m/s. For h=5.53 m and R=21.96 m. 0.6 m .R Select one: O a. 18.1 Ob. 29.3 O. 14.1 Od. 9.4 O e. 23.9 Time of maximum height Select one: O a. 0.56 Ob. 0.85 Oc. 1.09 Od. 1.43 O e. 1.76 Maximum height from the ground (m) Select one: O a. 2.0 Ob. 11.3 O. 3.1 Od. 4.0 Oe. 6.4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Choose the correct answer: 1. A 2 cm diameter water jet having a velocity of 25 m/s and inclined from the horizontal at an angle of 15°, impinges on a curved smooth vane which deflect the flow through 120° with horizontal. The force exerted by the jet on a vane will be: а. 253 N b. 287 N с. 312 N d. 417 N e. None of them.
2. A horizontal jet of water having a velocity of 25 m/s, diameter=2 cm strikes an inclined straight blade moving in the direction opposite to the direction of jet with a velocity of 10 m/s. If the inclination of the blade is 15° with the horizontal, the force developed on the blade per kg of water per second in the direction of the flow will be: а. 196 b. 217 с. 274 d. 292 e. None of them.
.A jet of velocity Vjet, cross-sectional area Ajet, and density Pjet impinges on a reversing vane and is turned through an angle of 180°. The vane is moving with velocity Vvane in the direction of the original jet. What is the force, Fvane, exerted on the vane by the water? A. 2p Ajot Vjet B. p Ajot Vjot C. 2p Ajd Vane D. 2p Ajet (Viet-Vane) 2
Reservoir A supplies water to a nozzle having diameter of 80 mm which discharge water 40 m below the reservoir water level at a velocity of 24 m/s. Determine the horsepower produced by the jet. a. 50.64 b. 49.32 c. 56.33 d. 46.33 note: indicate free body diagram
1. Solve and draw the figures i. Water is flowing through a pipe having diameters 30 cm and 15 cm at the bottom and upper end respec- tively. The intensity of pressure at the bottom end is 29.43 N/cm² and the pressure at the upper end is 14.715 N/cm?. Determine the difference in datum head if the rate of flow through pipe is 50 lit/s. [Ans. 14.618 m] ii. The water is flowing through a taper pipe of length 50 m having diameters 40 cm at the upper end and 20 cm at the lower end, at the rate of 60 litres/s. The pipe has a slope of 1 in 40. Find the pressure at the [Ans. 25.58 N/cm²] iii. A pipe of diameter 30 cm carries water at a velocity of 20 m/sec. The pressures at the points A and B are given as 34.335 N/cm² and 29.43 N/cm2 respectively, while the datum head at A and B are 25 m and 28 m. [Ans. 2 m] lower end if the pressure at the higher level is 24.525 N/em². Find the loss of head between A and B.
Water travels through a circular pipe with a diameter of 400 mm and at a speed of 5 m/s. The inertial force created by the flow is: Question 2Answer a. 100000 kgs/m b. 10000 kgs/m c. 1000 kgs/m d. 1000000 kgs/m
In a hydraulic installation, the water flows through a duct of 3 cm in diameter with a speed of 0.65 m/s; At the outlet of the duct there is a 0.3 cm diameter nozzle. If the nozzle, discharge the water to the conditions of the CDMX (???? = 77 ???, ? = 9.78 ? /?2 ), determine: a) The speed of the water when it leaves the nozzle b) If a pump is installed just before the duct inlet, and the duct inlet and outlet are at the same height. What is the fluid pressure at the pump outlet?
A reducing elbow is used to deflect water at a rate of 14kg/s in a horizontal pipe upwards through 30° while accelerating it. Patm FR2 FRE 30 cm 30 Pi The elbow discharges water into the atmosphere. The cross sectional area of the elbow is 113cm? at the inlet and 7cm? at the exit. The elevation difference between the centres of the exit and the inlet is 30cm. The weight of the elbow and the water in it are considered negligible. Which of the following expresses the inlet gauge pressure at the centre of the inlet and the resultant force required to hold the elbow in place. Takeg = 9.81 m/s? and density of water = 1000 kg/m?. Select one: O a. 202.2 kPa and 2064.8N O b. 202.2 kPa and 2164.8N с. 102.2 kPa and 2064.8N O d. 102.2kPa and 2164.8N
1. A water flows through pipe AB with diameter of 25 mm at 5 m/s. The end of pipe splits into two pipes which are pipe BC and pipe BD. The diameter of pipe BC is 15 mm and velocity of water in pipe BC is 3.1 m/s. Determine: i. ii. The flow rate of water in pipe BD. The velocity of water in pipe BD if the cross-sectional area of pipe BD is 2 times greater than the cross-sectional area of pipe BC.
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. 12.74m B. -4.67 m C. -2.72 m D. 2.56
Determine the kinetic energy flux of 0.87 m3/s of fluid (sp. Gr =2.53) discharging through a 94 mm diameter nozzle. (watts) Round your answer to 2 decimal places.
Oxygen enters a nozzle steadily at 3 kg/m3 and 35 m/s and leaves at 0.76 kg/m3 and 190 m/s. If the inlet area of the nozzle is 85 cm2, the exit area of the nozzle in cm2 is а. 43.49 ОБ. 65.24 C. 61.81 O d. 41.20