Please show all steps, not Ai generated, has been wrong before. I need to understand the process. A hot fluid passes through a thin-walled tube of 10-mm diameter and 1-m length, and acoolant at T = 25°C is in cross flow over the tube. When the flow rate is m 18 kg/h and the inlettemperature is Tm,i = 85°C, the outlet temperature is Tm,0 = 78°C.Hot fluidTmi = 85°Cm = 18 kg/hCoolantT = 25°C-Tube, D = 10 mm,L=1mTm,o= 78°CAssuming fully developed flow and thermal conditions in the tube, determine the outlet temperature,Tm,o, if the flow rate is increased by a factor of 2. That is, m = 36 kg /h, with all other conditions thesame. The thermophysical properties of the hot fluid are p = 1079 kg/m³, cp = 2637 J/kg · K, µ =0.0034 N s/m², and k = 0.261 W/m. K.

Need to determine the outlet temperature.

A hot fluid passes through a thin-walled tube of 10-mm diameter and 1-m length, and a coolant at T = 25°C is in cross flow over the tube. When the flow rate is m = 18 kg/h and the inlet temperature is Tm,i = 85°C, the outlet temperature is Tm,o = 78°C. Hot fluid Tm,i=85°C Coolant T = 25°C Tube, D = 10 mm, L=1m Tm,o=78°C

A hot fluid passes through a thin-walled tube of 10-mm diameter and 1-m length, and a coolant at T = 25°C is in cross flow over the tube. When the flow rate is m = 18 kg/h and the inlet temperature is Tm,i = 85°C, the outlet temperature is Tm,o = 78°C. Hot fluid Tm,i=85°C Coolant T = 25°C Tube, D = 10 mm, L=1m Tm,o=78°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A constant heat flux q = 200 W / m2 is applied to a circular section pipe with a diameter D = 50 mm and a length L = 8 m, and water flows at a flow of 0.01 kg / s under the pipe. The entrance temperature of the water to the pipe is 29 oC. Which of the following is the average fluid temperature at the outlet of the pipe (x = L) with the fluid transmission at 30 oC? a. 39.21 oC b. 84,23 oC c. 66,59 oC D. 61.43 oC e. 83,28 oC
Water at 27°C flows with a mean velocity of 1 m/s through a 1 km-long pipe of 0.25 m inside diameter. Answer the following: a. Is the flow hydrodynamically fully developed? Support your answer with calculations. b. Is the flow thermally fully developed? Support your answer with calculations. c. What is the pressure drop over the pipe length, if the pipe surface is smooth? (Ans: 0.289 Bar) d. What is the pump power requirement, if the pipe surface is smooth? (Ans: 1.42 kW)
Flow Characteristics (Entrance Effect) -Why is the Δ P/ L Line extrapolated to the tube entrance for the calculation of the entrance loss coefficient, KL ?
Water at 10oC enters a tube of 0.1 m diameter at the mean flow velocity of 0.4 kg/s. Calculate the exit water temperature if the tube is 15 m long and the wall temperature is constant 30oC.
Helium at 25°C and 110 kPa (absolute) flows into a copper tube (1-1/4-standard, type M) that is 10 m long. Is the flow fully developed at tube end if the helium mass flow rate is 0.02 kg/s? Ethyl alcohol flows into a 6 cm ID pipe through a well-rounded entrance. After 20 cm of pipe length, measurements taken in the pipe show that the flow is fully developed. Determine the volume flow rate in the pipe, assuming laminar flow exists.
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. What is the % of pressure drop? (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol
The velocity profile in fully developed laminar flow in a circular pipe of inner radius ro, is given by v=9(1-7) Find: 1) Plot the velocity profile. 2) The volume of water flows out of the pipe in 0.2 min?
Sketch the shear stress and velocity distribution for laminar flow across a pipe section?
Water is flowing in a long cylindrical tube at a mass flowrate of 0.01 kg/s. If the tube diameter is 10mm, water density is 1060 kg/m3 and water viscosity is 0.001 Pa.s, (i). calculate the Reynolds number of the flow; (ii). is the flow laminar or turbulent?
A liquid while flowing through a thin-walled cylindrical copper pipe (D=10 cm, L=1 m) with a mass flow rate of 0.001 kg/s is heated from Ti= 33 °C to Te= 98 °C by supplying constant surface heat flux to the pipe surface (all the heat is transferred to the fluid). Considering fully developed laminar flow in the pipe, what is the surface temperature of the pipe at the exit in Celsius? (For the fluid use, Cp 1800 J/kg.K, k= 0.2 W/m.K) = constant 117111 q's m = 0.001 kg/s 111 L=1m D= 10 cm
A 30mm ID, 50mm OD aluminum round tube passes air through it at a rate of 0.08 m^3/s. A 100W electric heater blanket covers the outside of the 2m long tube. If the air enters the tube at 100 celsius , what temperature does it exit at? Assume that the heater blanket is perfectly insulated on the back side (no heat loss out the back). Note-RT is 25 celsius
derive the navier stoke equation to Vz (in function r) in a cylindrical pipe with the maksimum radius of a and L as the length of the pipe in a laminar and steady flow