A lap joint is made of 2 steel plates 10 mm x 100 mm joined by 4 - 16 mm diameter bolts. The joint carries a 120 kN load. Compute the bearing stress between the bolts and the plates. Select one: O a. 187.5 MPa O b. 172.5 MPa O c. 154.2 MPa O d. 168.8 MPa

A lap joint is made of 2 steel plates 10 mm x 100 mm joined by 4 - 16 mm diameter bolts. The joint carries a 120 kN load. Compute the bearing stress between the bolts and the plates. Select one: O a. 187.5 MPa O b. 172.5 MPa O c. 154.2 MPa O d. 168.8 MPa

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.15.5P

See similar textbooks

Related questions

Q: Driven by pressurized air in a tank, water flows through pipes (L₁ = 40 m, L2 = 80 m, L3 = 20 m) of…

Q: IO ights 800 kg and just en the depth of water e decreases to 4 mete friction between dock

Q: At a temperature of 29.8 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time…

A: Change in length of steel rod,

Q: 2. Calculate area moment of inertia about the horizontal and vertical axis passing through centroi…

Q: A square culvert is connected to the outlet point of the natural flow path for the 50yr return…

Q: Calculate the discharge (m³/s) in a river that is affect by back-water, corresponding to fall (F₂)…

A: given- fall value-F2=1.4 mfall value-F1=0.6 mdischarge for fall value of F1Q1=280 m3/sm=0.5

Q: A reinforced concrete column 500 mm × 500 mm in a section is reinforced with 4 steel bars of 25 mm…

A: E for steel = 210×10^3N/mm2 E for concrete = 14×10^3 N/mm2 Steel bars = 4 dia = 25mm Column load=…

Q: Given the beam and loading show below • Draw the shear and moment diagrams. Label all significant…

Q: 2/89 Express F as a vector in terms of the unit vectors i, j, and k. Determine the angle between F…

A: image of detailed answer is uploaded in step 2

Q: D gram

A: solution of above problem is below:

Q: Pressure exerted on a block of wood present at a depth of 30 m under water?

A: Given:Depth, d=30 m

Q: Completely solve and box the final answer. Write legibly 1. A built up wooden beam is made up of…

Q: Problem I. Solve the problem using Conjugate Beam Method. Given the figure, determine the following…

Q: Assignment 1- Annalise the loaded frame Draw bending moment diagram co= 60 kN/m B 3 m 3 m 6 m 6 m &…

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

Q: What are the different types of streaking?

Q: Consider the following data for concrete with mild exposure Water-cement ratio = 0.50 Water 191.6…

A: For 1 m3 of concrete Water cement ratio = 0.5 Amount of water = 191.6 l =191.6 kg Cement content =…

Q: 2,000 N acts from A towards B. 550 mm 220 mm Determine the moment of the force about point C in N-m.…

Q: Note: please use set B data W 2° Me A B C * 4 m 2 m The cantilever beam above is made up of concrete…

Q: C. Calculate the modulus of elastisity for a material which produces the following data when…

Q: What is the total resultant vertical load in the beam AB? (N) At what distance from A does the…

A: The figure shows a simply supported beam of16 m with uniformly varying load acting up to 9m from A…

Q: Q1: An unconfined aquifer in a stratum of clean sand and gravel has a hydraulic conductivity of 10-2…

Q: A solid shaft 138 mm in diameter is to transmit 5.19 MW at 20 Hz Use G-83 GPa Find the maximum…

Q: 4 ht K H F В C D E -3ft -- 36 -- 3а -- 31 -- 3 ft - ft ft ft Y Y y P Р P Р P Р P P Р

A: Given data:- Below truss diagram is given;

Q: A soil sample is required to have degree of saturation 60% at 18% water content. If specific gravity…

Q: In a steel flat plate a state of plane stress available. Calculate o, and principal stresse o, -140…

Q: Q4: The bearings and lengths of straights R1-X1 and X1-R4 taken from Table below, are as follows:…

Q: ▪ A roadway is determined to have 400 18-kip single axles, 200 24-kip single axles, and 100 40- kip…

A: PSI = 4.5%So= 0.4TSI = 2.5R = 99%Single Axle load = 400 18-kiptandom Axle load = 200 24-kiptriple…

Q: For the truss and loading shown, determine most economical cross-sectional area (in in2) of member…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: A trapezoidal channel has a bottom width of 6 m and a side slope of 1:1. The depth of flow is 2 m at…

A: given- bottom width b=6 mside slope =1:1depth of flow y=2 mdischarge Q=24 m3/sg=10 m/s2

Q: Liquid 100kpa 140kpa 2.7m 2.4m

A: Given data:-

Q: Question 8 Draw the downstream water profile for the following step-up and step-down conditions.…

Q: The extra widening required for a two-lane national highway at a horizontal curve of 275 m radius,…

A: given design speed V=80 kmphRadius of curveR=275 mradius of wheel base L=7.5 m

Q: power (in kW) recovered in the turbine

A: Given:' Density of water= 9810 N/m3 = 1000.34 kg/m3 g = 10 m/s2 Efficiency of turbine and pump = 70%…

Q: A surveyor completed a closed traverse around four survey marks, starting at station 1 and finishing…

A: Angular misclosure = 180°-49°59'30''-60°-70°= 0°0'30'' Yes It would be appropriate to adjust the…

Q: A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress…

Q: A truck and trailer combination crossing a 17-m span has axle loads of 10, 20, and 30 kN separated…

A: Given, loads = 10 KN, 20 KN and 30 KN. Resultant, R = 60 KN at 5m from 1st load. Span=17 m

Q: Situation 3 A compressive strength test were conducted to the following cylinder, Cylinder 1 3015…

A: Given data, Diameter d = 634 in

Q: A 520 ft long equal-tangent crest vertical curve connects tangents that intersect at station 340+00…

A: Given Data: long = 520ft elevation = 1325ft initial grade = +4.0

Q: Water flows through a pipe having an inner radius of 10 mm at the rate of 36 kg/h at 25°C. The…

A: Given:radius; R=10 mmDynamic viscosity of water; μ=0.001 kg/m.sMass flow rate; Q=36 kg/hr=0.01 kg/s

Q: please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS The compound…

A: Given data: T=1179.9 NmU=4330 Nmx=3.03 my=2.25 mz=1.34 md=94 mme=76 mmCBr=35 GPaCst=83 GPaCal=28 GPa

Q: te the vertical and horizontal deflection at point B using virtual work method. Show COMPLETE…

A: Given :

Q: The liquid in blue color has a density of 500 kg/m³. Calculate the gage pressure P, in kpa for h= 5…

Q: The compound bar ABCD has a uniform cross-sectional area of 0.36 in2.Determine the change in length…

Q: Problem III. Solve the problem using Conjugate Beam Method. From the given fixed beam at both ends,…

A: A beam and loading diagram is given in the figure as shown above and it has been asked in the…

Q: Determine the shear force 9.44 ft to the right of point A for the beam shown belowif T = 1093 lb ft,…

A: A beam with load arrangement is given as shown in the figure above and it has been asked in the…

Q: please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS For the beam…

Q: Q3. A copper bar of 50 mm*50 mm cross section is 1.5 m long, it subjected to an axial pull of 100…

Q: Calculate the flux of water through MF and UF membranes operating at 1 bar pressure and 298 K.…

Concept explainers

Introduction to Architectural Drafting

Architectural drafting converts vision and ideas into technical drawings and detailed plans for the construction of buildings, such as institutional, residential, and commercial buildings. It helps engineers and architects to outline the working data and details, such as structure type, codes, elements, and kind of materials.

Question

SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION

A lap joint is made of 2 steel plates 10 mm x 100 mm joined by 4 - 16 mm diameter bolts. The
joint carries a 120 kN load. Compute the bearing stress between the bolts and the plates.
Select one:
O a. 187.5 MPa
O b. 172.5 MPa
O c. 154.2 MPa
O d. 168.8 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The tension member is fastened togother using two bolts, one on each side of the member as shown. Each bolt has a diameter of 0 3 in The allowable shear stress for the bolts is Tall 12 ksi and the allowable average normal stress is oallow- 19 ksi Part A Determine the maximum load P that can be applied to the member Express your answer to three significant figures and include appropriate units. Pas Value Units
Q4\ Which of the following is a zero-force member? 3 8KN 4 G 4 エ子c D. 4 B AC BD IF ID
A bolted connection shown is bolted with a A-325 bolts with an allowable shearing stress of 207 MPa. A-36 steel is used. The applied force "T" is equally divided among the bolts. Assume bolt hole diameter to be 3 mm bigger than bolt diameter. Diameter of bolt is 20 mm. T/2 T T/2 10 mr 10 mm T/2 300 mm T/2 Determine the capacity of the connection if shearing governs in kN. A 1548.58 B 1170.56 1290.62 D 1439.25 000
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm
أ.د. رمضان المبروك A PL170mm x 10mm tension member is welded to a gusset plate as shown in Figure below. The steel is A36. Assume that Ae = Ag and compute the following. %3D fy = 250 MPa & f, = 400 MPa %3D %3D PL 170mmx10mm a. The design strength for LRFD. . The allowable strength for ASD. roblem (4):
A double-row butt joint is used as a connection. It is made up of two 210mm by 12mm cover plates and 210 mm by 20 mm main plate. The plates are to be connected by 22 mm diameter rivets. The allowable stresses are 65 MPa for shear, 83 MPa for tension, and 135 MPa for bearing. Assume that each hole is 3 mm larger than the rivet diameter. Calculate the largest value for P that can be applied without exceeding the allowable stress for tension. o a. 418.3 kN b. 330.8 kN c. 348.6 kN (Ctrl) o d. 265.6 kN Pe
Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117
2. For the figure shown, calculate the net area of the 10 x 200 mm plate. The plate is connected at its end with two lines of 20 mm bolts. Using LRFD, determine the load P that the plates can carry against tensile yielding in the gross section and the tensile rupture in the net section. Use A-36 steel. PL 5x200mm PL 5x200mm Pu PL 10x200mm Pu
Situation 2. Two plates each with thicknessF16mm are bolted together with6 -22mm dimater bolts forming a lap conne ction. Bolt spacing are as follows: S1 = 40mm, S2 = 80mm, Sa = 100mm. Bolt hole diameter=25 mm 50 250mm 30 30 60 75 Allowable stress: Tensile stess on gross area of the plate=0.60 Fy Tensile stress on net area of the plate=0.5Fy Shear Stress of the bolt Fv=120MPA Bearing Stress of the bot Fp=1.2 Fu Calculate the permiss ible tensile load P under the following Conditions: 4. Based on shear capacity of bolts 5. Based on bearing capacity of bolts 6. Based on block shear strength (taking into consideration the failure path given in the figure below) 40 80 16 mm 40 180 mm 40 Bearing Failure Path #1 140 209 Bearing Failure Path #2
The lap joint in the figure is fastened by four 20 mm Ø A325X bolts. Calculate the maximum safe load P that can be applied if the plates are 25 mm thick A-36 steel Use ASD. 4 @ 40 mm P 2 @ 60 mm P
2. The A-36 steel Bar BC had a diameter of 40 mm before the two loads, P, were applied. If after loading, the new diameter of the bar is 39.995 mm, what was P? P -1 m B 0.75 m 1 m
9. The gusset shown is riveted to the column flange by 7-20mm diameter rivet single shear. Determine the stress in the most heavily loaded bolt. If the design shear stress is 400MPA, determine the ultimate load that the connections can carry. Using the design shear stress how much more torque can the connections carry? 140 kN 200 mm 175 mm 7- 20 mm bolts 150 mm 150 mm 150 mm