Answered: A long cylindrical shell closed at both…

A long cylindrical shell closed at both the ends, this shell is subjected to an internal pressure 'P'. Find the ratio of the longitudinal stress to the circumferential stress developed in the shell?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.17P: A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at...

See similar textbooks

Related questions

Q: First we will analyze the situation when P-500 N. The connection at A is a pin and the connection at…

A: As per Expert Guidelines, we are supposed to slove only first three parts of the given multi part…

Q: 1. Solar Collector Problem: From the diameter of the sun and the earth and the mean distance of sun…

Q: Determine the area moments of inertial and ly. Given that c = 0.94 in. 4 in. y 0.5 in. -0.5 in. 4…

A: From the given figure: The radius of curvature →c=0.94 in So the moment of inertia about X axis:…

Q: to a point C located on the vertical wall. If the tension in the cable is 380 lb, determine the…

Q: Iron (Fe) undergoes an allotropic transformation at 912°C: upon heating from a BCC (a phase) to an…

Q: Determine the moments of inertia of the Z-section about its centroidal xo- and yo-axes. 18 mm…

Q: Water enters a perforated irrigation pipe (Length L, diameter D) with a uniform velocity Uin=10m/s.…

A: The pipe diameter is D. The inlet velocity of water is Uin=10 m/s. The outer velocity is Uout=80…

Q: 3. A 20-mm-diameter commercial steel pipe, 30 m long is used to drain an oil tank. Determine the…

A: Question A 20 - mm diameter commercial steel pipe, 30 m long is used to drain an oil tank. Neglect…

Q: Determine the magnitude of the moment of the force F about the base line AB of the tripod. a 4.9m…

Q: P18-1. The bucket of the excavator is supported by member AB and the pin support at C. If W = 1500…

Q: e rigid beam is supported by a pin at C and an A-36 steel guy wire AB.

A: Given: The diameter of wire is, d=0.4 in. The distribution load is, w=100 lb/ft. The length of the…

Q: A reversed Carnot cycle is given which operates between the temperature limits of 27°C and -3°C So…

A: Given:Th= 27°C or 300 KTl=-3°C or 270 KFind,Ratio of Coefficient of performance of refrigerator to…

Q: Critical sonic flow: Critical and Stagnation Conditions Homework: A gas is contained in a large…

Q: The pitcher throws the baseball with a release angle of 2 degree below horizontal, and speed of 47…

A: Given data:- release angle (θ)=2° initial velocity V0=47 m/s distance(s) =18.5 m To find:- Time…

Q: I just took a water bottle out of my refrigerator (0₁ = 3°C) and placed it on the kitchen counter.…

A: The given information in the problem is shown in the following attached image:

Q: 7. Electric power is to be generated by installing a hydraulic turbine-generator at a site 70 m…

Q: four pounds of air gain 0.491 Btu/degree Rankine of entropy during a nonflow isothermal process. if…

A: Given that: Mass of air is 4 lbm. Air gains 0.491 Btu/R entropy during a non flow isothermal…

Q: The actual sales of car manufacturer in January is 120 units but the car manufacturer underestimated…

A: Given data: ▪︎The actual sales in the month of January: DJan. = 120 units ▪︎The car manufacturer…

Q: A fin losses 6 W heat. The effectiveness and efficiency of the fin are 3 and 0.75 respectively.…

Q: II. Photovoltaics' Problem For a photon with a wavelength of 832 nm (green light), calculate: a) the…

Q: Explain the application of the first law of thermodynamics to appropriate systems

Q: Suppose a mass-spring system has spring constant 712 N/m and mass 4.4 kg. The mass is displaced in…

Q: Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB.…

Q: Rods are mass produced by a machine. The specification required the length of each rod to be between…

A: To find: (a) The percentage of rods produced which would be rejected if the mean length of the rods…

Q: The rigid tank shown in the figure has a volume of 0.05 m³ and initially contains a two-phase…

Q: The hydraulic cylinder gives pin A a constant velocity v = 2.0 m/s along its axis for an interval of…

A: Given velocity of pin A and the inclination angles. Required: Velocity and acceleration.

Q: 6. Carbon Dioxide at p₁ = 500 psia,₁ min volume to 130°F in an internally reversible manner. For m =…

A: GivenP1=500psia =500×144=72000 psfV1=1 ft3/mint1=200oF=(200°F − 32) × 5/9 + 273.15 =…

Q: The shear leg derrick is used to haul the 200-kg net of fish to the dock. Determine the compressive…

Q: Find Reactions at R, and R₂ assume equally distributed +1053 lbs/fr 180.25 200,000ths X0=15° R₁…

Q: aking E=200GPa, A 200 × 100 × 50 mm steel block is subjected to a hydrostatic pressure of 15 MPa.…

A: Given:Dimension of steel block=200×100×50 mmHydrostatic pressure=15 MPaE=200 GPaϑ=0.3Find,Change in…

Q: is flowing through a horizontal pipe of diameter 200 mm at a velocity of 3 m/s. A circular solid…

A: Given:Pipe diameter=200 mm or 0.2 mvelocity=3 m/s

Q: 22: A shaft is made of material has stress-strain curve is given by o=225+125 € 0.25 MPa .The shaft…

A: The stress-strain curve is given by σ=225+125ε0.25 MPa The velocity is v=120 mm/min⇒v=2 mm/s The…

Q: escribe with the aid of diagrams the operational sequence of four stroke spark ignition and four…

A: According to the question we need to explain four-stroke spark ignition engine and Four-stroke…

Q: A car moves along a straight line. The car starts to move from Thi- Qar toward Baghdad with a…

Q: Determine the resultant internal loadings acting on the cross section at B for the piping system…

Q: Problem 6: Inputs: a = 600 mm b = 400 mm c = 200 mm F = 100 N The line of action of the force vector…

Q: A Freon 12 plant operates between saturation temperature limits of -5°C℃ and 40°C. The refrigerant…

Q: 1) Draw and calculate the resultant moment. 0= 19 deg -6 10 25 7 6.45 1.5° -5 20 y Z X

A: Given: Force→F1=-6i+10j+25k Force→F2=5i-5j+20k And from all the distances given in the figure:…

Q: A copper rod is rigidly attached between a steel rod and a brass rod. Axial loads are applied at the…

Q: Use the graphical method to construct the shear-force diagram and identify the magnitude of the…

Q: A reversed Carnot cycle is given which operates between the temperature limits of 27°C and -3°C, So…

Q: An automobile of weight w is shown in figure. A pull P is applied as shown. The reaction at the…

A: Given:Weight of automobile=wPull force=PFind,Reaction at the front wheel A?

Q: To maintain a dwelling steadily at 68°F on a day when the outside temperature is 30°F, heating must…

A: (a) To find: The electrical power required. Given: The temperature of the hot reservoir is…

Q: A tension test specimen had a gauge length of 2.5 in. After the test, the gauge length had increased…

A: In this problem, we will compute the uncertainty in the percentage elongation of the specimen by…

Q: orseshoe player throw the horseshoe with an initial speed vo = 40 ft/sec.find the ranges for the…

Q: 9. A certain ideal gas whose R = 278.6 1/kgm.K and C₂ = 1.015 kJ/kgm.K expands isentropically from…

A: GivenR=278.6 J/kgKCp=1.015 kJ/kgK=1015 J/kgKPVy=ConstantP1=1517 kPaT1=288oC=288+273=561KP2=965…

Q: Example - Single cylinder 4-stroke engine The torque diagram for a single cylinder engine is shown…

A: Given1cm=100 Nm1cm=90degN=1500 rpmn=±2%σh=5 MN/m2ρ=7200 kg/m3

Q: Q2. If FAB = 500 lb and FAC = 800 lb. Determine the magnitude of the resultant force and the…

A: According to the given data FAB=500lb FAC=800lb we need to find Resultant and co-ordinates…

Q: Heat is rejected from the condenser of a heat pump cycle by refrigerant-134a entering at 700 kPa and…

Question

A long cylindrical shell closed at both the ends, this shell is subjected to an internal pressure 'P'. Find the ratio of the longitudinal stress to the circumferential stress developed in the shell?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are known to be ??x=-92 psi and txy= -7 psi. Find the principal stresses on the element and show them on a sketch of a properly oriented clement.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.