A M42x4.5 Grade 10.9 bolt 60 cm in length is loaded to 85% of its proof strength. The bolt is not lubricated, though traces of lubrication may be present. What is the required torque, deformation, and torque angle? The modulus of elasticity is E = 207 x 10' N/m. Use 830 MPa as proof strength.

A M42x4.5 Grade 10.9 bolt 60 cm in length is loaded to 85% of its proof strength. The bolt is not lubricated, though traces of lubrication may be present. What is the required torque, deformation, and torque angle? The modulus of elasticity is E = 207 x 10' N/m. Use 830 MPa as proof strength.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Grade 1020 steel has a yield strength of 42 ksi and an elastic modulus of 30 Mpsi. Another grade of steel has a yield strength of 132 ksi. What is its elastic modulus? (Express your answer as an integer.) E = |Mpsi
Screw M14*2 Fasten with a hexagonal nut The bolt material meets the requirements within the 4.8 property class and the nut material belongs to the 5 property class Find the largest tensile strength of the bolt that can be tolerated without breaking
M P 1: Y A :s.google.com Q1 * Find the number of bolts M8 1 which made from SAE Grade 4 steel that should be used to provide a clamping force of 60 KN between two components of a machine. Also, specify the required tightening torque. (Hint: assume that cach bolt is limited to be stressed to 65% of its proof strength). 1 Add file Q2 * A flat plate with a central hole is subjected to an axial tensile force F of 9.8 KN, as shown in the figure below. Calculate the minimum thickness t of the plate. Given that the material of the plate can support maximum tensile stress of 75 N.mm, w = 10 cm and d = 3 cm. Thickness =t F 1 Add file Submit Clear form II
Define the rigid body used in statics. According to this; rigidity of bolt-nut connected elementBased on the value, the bolt diameter is 20 mm and the safe value of the bolt material.Calculate the stiffness values of the bolt and the intermediate element plate. (Note: Bolt's9x10 ^ 2 times as stress value ??? / cm ^ 2take as.). Strain gaugeElongation in bolt length measured with 250 ??, shortening amount in intermediate element platesIt was measured at 125 ??.
Q4- Explain the following state "other mechanical properties often may be estimated from hardness data" Q5- "Engineering stress-stain curve and True stress-strain curve are similar". Why? Q6- Is it possible utilized bending test for non-brittle materials? Why? Q7- Engineering stress-strain curve for the compression test is similar to that of the tensile test. But the shape of plastic region is different. Explain why? Q8- find the yield point for brittle and ductile materials?
(7) The cylinder head of a 10"x18" refrigerant compressor is attached by 10 stud bolts made of SAE grade 5. The maximum cylinder pressure is 350psi. (a) What size of bolt is to be used? (b) What approximate tightening torque should be applied to induce a tightening stress of 0.9 time of the proof stress?
Investigate the helical compression springs with squared and ground ends fabricated from A313 stainless steel to see if they are solid safe. If not, what is the largest free length to which they can be wound using ng = 1.2? Given: d= 0.0508 in, OD = 0.249 in, Nt = 11.2 coils, and Lo= 0.72 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the values of the solid height, Ls, the spring rate, k, and the shear stress. The solid height, Ls, is .569 in. The spring rate, k, is Ibf/in. The shear stress is kpsi.
Required information For a bolted assembly with six bolts, the stiffness of each bolt is kb 2 Mibf/in and the stiffness of the members is km = 13 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. It is desired to find the range of torque that a mechanic could apply to initially preload the bolts without expecting failure once the joint is loaded. Assume a torque coefficient of K = 0.2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts once the load is applied. The maximum bolt preload that can be applied is Ibf.
Q4/ A bolt M18× 1.5 ISO metric thread is subjected to a fluctuating load of 0 to 10000N. Endurance strength=D200 MPa. Bolt and the past are of the same material and length. Yield stress=480 MPa, stress concentration factor 3.85, component area 362mm2. Calculate i) Factor of safety without preload ii) Minimum initial load to prevent joint opening iii) Factor of safety with 9 kN preload iv) Minimum force in the part for a given loading and a preload of 9 kN.
Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia = 0.1959"), 3" long, and a head height of 0.1875", if it is subjected to a load of 426 lbs.
3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.
A bolt with a square threaded screw has mean diameter of 25 mm and a pitch of 3 mm. It carries an axial thrust of 10 kN on the bolt head of 25 mm mean radius. If u = 0.12, find the force required at the end of a spanner 450 mm long, in tightening up the bolt. 3. [Ans. 110.8 N] A turn buckle with right and left hand threads is used to counle twvo railway coaches The threads