//////////A metal bar is made out of Ti-6A1-4V titanium (stiffness E = 120GPa) and has a diameter d = 35 mm with the end at A fixed tothe wall. There is a distributed axial load of w = 60 kN/m.Length of the bar is L₁ = 1200 mm. Calculate the displacementof point A relative to the wall.dw [kN/m]The displacement at A is 8 =mmA030BY NO SA2021 Cathy Zupke

Step 1:the displacement is the distance from the original position of a point to its final location…

Answered: ////////// A metal bar is made out of…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Part of a two story building is shown in the figure in which a concerte column and a steel column are used in the first and second floor. The compressive force on the roof of the second floor is PC = 370 kN. The compressive force on the first floor is PB = 420 kN. The steel [Esteel = 200 GPa] column is a wide angle steel shape that has a cross section area of A2 = 1950 mm2. The concrete [Econcrete = 30 GPa] column has a circular section with a diameter of d = 560 mm.[L1 = 5.6 m, L2 = 5.6 m] Using this equation FL/AE
Solve the effective normal force on the rod CD Use units [N,mm] The mass of the load is: mk=59033kg
3 An aluminum stepped shaft (E = 10 × 10³ ksi, v = 0.35), is subjected to three axial forces as shown. For P1= 100 lb, P2 = 128 lb, P3=386 lb, L1=2.5 in, L2= 2.0 in, L3= 1.0 in, determine the elongated/shortened length of section CD. [106 in] (sign sensitive) 1.5 in. DIC L; 1 in. B P₂ 0.5 in. L₁ A₁ P₁
14. A bar of 2 m length, 20 mm breadth and 15 mm thickness is subjected to a tensile load of 30 kN. Find the final volume of the bar, if the Poisson's ratio is 0.25 and Young's modulus is 200 GN/m?. [Ans. 600 150 mm³]
Stiven: A 2 in diameter Rod wo in long elongares 0.12 in under L load of 60 kip. The diamurer of Rod decrease 0.004 in during loading modulus of Elasticity? Poisson's ratio?" and " ↓ uw T (ks i) = Find moddus of Rigidity ? ↓ UniT (ksi] unit 1
Compute the reduced compliance [S] matrix for a lamina with E1 = 35 GPa, E2 = 3.5 GPa, V12 = 0.3, G12 = 1.75 GPa, and G23 = 0.35 GPa.
An aluminum alloy [E = 8400 ksi] pipe with a cross-sectional area of A₁ = 4.20 in.² is connected at flange B to a steel [E = 23800 ksi] pipe with a cross-sectional area of A₂ = 2.96 in.². The assembly is connected to rigid supports at A and C. Assume L₁= 154 in., L₂= 200 in., and P = 56 kips. For the loading shown, determine: (a) the normal stresses in aluminum pipe (1) and steel pipe (2) (₁, ₂ use positive if tensile, negative if compressive). (b) the deflection ug (use positive if it moves to the right and negative if it moves to the left) of flange B. Answers: (a) 6₁ (b) ug = (1) L₁ Save for Later B eTextbook and Media L2 ksi, 0₂ = i in. ksi, Attempts: 0 of 5 used Submit Answer
A steel [E = 25500 ksi] pipe column (1) with a cross-sectional area of A1 = 5.60 in.2 is connected at flange 8 to an aluminum alloy [E = 17500 ksi] pipe (2) with a cross-sectional area of A2 = 4.40 in.2. The assembly is connected to rigid supports at A and C. For the loading shown, determine the normal force in the steel pipe (1). A (1) 120 in. B 30 kips 30 kips 144 in. C
In the train bridge in the figure, select the F1 and F2 forces from 107 to 207 kN with a non- zero end. Find the force on the bar BC and whether it is the pull. ? (Note: Fill in the table.) F1= 125 kN F2= 165 kN a) BC = ? [kN] b) compression or в tension? F1 KN F2 KN to 10 m 10m 10 m 10 m
1. Arectangular plate 50 mm x 10 mm with a hole 10 mm diameter is subjected to an axial load of 10KN. Taking stress concentration into account, find the maximum stress induced. [Ans. 50 MPa]
band Pass FI.. 目Readi This course EHide block An aluminum pipe is filled in concrete is subjected to a pure compressive force as shown in the figure below. Determine the factor of safety against compressive stress acting on the column. The pipe has an outer diameter of 60 mm and inner diameter of 50 mm. The aluminum and the polymer concrete have the following material properties: Young's modulus: Eal = 70 GPa (aluminum), Ecr = 30 GPa (concrete). Yield compressive strength: Sy-al = 180 MPa (aluminum), Sy-cr = 60 MPa (concrete). 100 kN 500 mm Select one: O FS = 1.7
A steel [E = 25500 ksi] pipe column (1) with a cross-sectional area of A1 = 5.60 in.2 is connected at flange B to an aluminum alloy [E = 17500 ksi] pipe (2) with a cross-sectional area of A2 = 4.40 in.2. The assembly is connected to rigid supports at A and C. For the loading shown, determine the normal force in the steel pipe (1).

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS