A motor applies 360 lb-ft of torque which is transferred through gears to shaft BD. At gear C the removed torque is Tc = 500 lb-ft. The shaft between the motor and gear A is 30". All shafts are solid steel with a 1.5" diameter and G = 12,000 ksi. Determine a) The gear tooth force between A and B Ans: 1080 lb b) The torque removed at D c) The maximum overall shear stress in the shafts Ans: 400 lb-ft d) The angle of rotation of gear D with respect to the motor 60 in. 40 in. 10-in. diameter Tc B Tp (1) 4-in. diameter

A motor applies 360 lb-ft of torque which is transferred through gears to shaft BD. At gear C the removed torque is Tc = 500 lb-ft. The shaft between the motor and gear A is 30". All shafts are solid steel with a 1.5" diameter and G = 12,000 ksi. Determine a) The gear tooth force between A and B Ans: 1080 lb b) The torque removed at D c) The maximum overall shear stress in the shafts Ans: 400 lb-ft d) The angle of rotation of gear D with respect to the motor 60 in. 40 in. 10-in. diameter Tc B Tp (1) 4-in. diameter

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft rotates at a speed of 679 rpm and transmits a power of 5 kW. If the maximum torque exceeds the mean torque by 23%. Take the value of allowable shear stress as 71 MPa. Find the value of the following i) Torque transmitted in N-m ii) Maximum torque transmitted in N-m iii) Diameter of the shaft in mm.
4. A flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and 8-12mm diameter steel on a concentric bolt circle 260mm in diameter. What torque can be applied without exceeding a shearing stress of 60MPa in the bolts? B) Determine the number of 10mm steel bolts that must be used on the 320mm bolt circle of the coupling to increase the torque capacity by 6KN-m.
A steel shaft ABCD of length L=6.5 is shown in Figure 4. Given the torque at A,B,C and D is 80 kNm, 150 kNm, 60 kNm and 10 kNm, respectively. The shaft has a diameter of 200mm. Use G=79.3 GPa a) Determine the angle of twist of the end A. b) Calculate the angle of twist of A relative to C. c) Plot a diagram of torque, T versus length, L of the shaft.
A steel shaft ABCD of length L = 6.5 is shown in Figure 4. Given the torque at A, B, C andD is 80 kNm, 150 kNm, 60 kNm and 10 kNm, respectively. The shaft has a diameter of200 mm.a) Determine the angle of twist of the end A. b) Calculate the angle of twist of A relative to C. c) Plot a diagram of torque, T versus length, L of the shaft.
The bearings at A and B exert only x and z components of force on the steel shaft. a) Draw shear, moment and torque diagrams displaying values at each section of interest (A, B and Gear points). b) Determine the shaft's diameter to the nearest integer millimeter (Roundup) so that it can resist the loadings of the gears without exceeding an allowable shear stress Tall- Fx A 75 mm 50 mm 150 mm 350 mm B F, 250 mm Fx=15KN,Fz=22.5kN,allowable shear stress=90MPA
A solid shaft with a diameter of 20 mm is shown below. The shaft is fixed at points A and B. In the diagram, L- 1.6 m, T- 200 N-m, and T2- 450 N-m. a) Draw a torque diagram for this shaft. b) Determine the maximum shear stress in the shaft. D 0.3 m T В 0.2 m
A flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and 8-12mm diameter on a concentric bolt circle 260mm in diameter. What torque can be applied without exceeding a shearing stress of 60MPa in the bolts? B) Determine the number of 10mm steel bolts that must be used on the 320mm bolt circle of the coupling to increase the torque capacity by 6KN-m.
Question 3 A shaft ABCD is shown in Figure 3 with total length, L = 2.1 m. The shaft BC is hollow with inner and outer diameters of 90 mm and 120 mm, respectively. Shafts AB and CD are solid with diameter d. Given the torque at A, B, C and D is 6 kNm, 14 kNm, 26 kNm and 6 kNm, respectively. a) Determine the maximum and minimum shearing stress in shaft BC. b) Calculate the required diameter, d of shafts AB and CD if the allowable shearing stress in these shafts is 65 MPa. 0.9 m 0.7 m 0.5 m A 120 mm TA = 6 kN-m В TR = 14 kN-m C Tc= 26 kN·m D Tp = 6 kN-m Figure 3
Question 3 A steel shaft ABCD of length L = 6.5 is shown in Figure 4. Given the torque at A, B, C and D is 80 kNm, 150 kNm, 60 kNm and 10 kNm, respectively. The shaft has a diameter of 200 mm. a) Determine the angle of twist of the end A. b) Calculate the angle of twist of A relative to C. c) Plot a diagram of torque, T versus length, L of the shaft. 1.5 m 2 m 3 m 10 kN·m 60 kN·m 150 kN·m 80 kN m
A steel shaft can be manufactured as a circular rod with a solid body or a circular tube. The shaft is required to bear a torque of 1200 N.m. Since the shear strength for the shaft material is 40 MPa, the maximum permitted unit torsion angle of the bar is 0.750 / m and the shear modulus of the steel is G = 78 GPa;a) Find the required diameter d0 for a solid circle shaft.b) Find the required outer diameter d2 for a ring section shaft whose thickness is 1/10 of the outer diameter.c) Find the diameter ratio (d2 / d0) and the weight ratio for ring cross section and solid section shafts.
2) The minimum outer diameter required for a hollow shaft if the shaft inner stress of tallow = 75 MPa. The shaft is designed to transmit 40 kW of power at 900 ) The drive shaft of a motor is made of a material having an allowing shear diameter is designed to be 80 percent of this outer diameter. 1. rpm. Determine 1) The minimum diameter required for a solid shaft. a
QUESTION 2 A shaft rotates at 300 rpm. 1). If it carries a spur gear that delivers 5 hp to a mating gear and the spur gear has the diametrical pitch of 10, pressure angle of 20°, and 80 teeth, determine a). The resultant force exerted on the shaft = Ib 2). If it carries a sprocket that delivers 4 hp to a mating sprocket and the sprocket has the pitch diameter of 6", determine b). The force exerted on the shaft Ib 3). If it carries a "flat-belt pulley" (Note: NOT V-Belt Drive) that delivers 8hp to another flat-belt pulley and the pitch diameter of the pulley is 20", determine C). The force exerted on the shaft: Ib