A particular thermodynamic cycle acting on a monatomic ideal gas (y = 1.67) includes an isobaric expansion, an isochoric cooling, and then a isothermic contraction. The PV diagram is shown in the image below. PA V The isobaric expansion occurs at a pressure of 1.8 × 105 Pa and changes the volume of the gas from 6.7 × 10 2 m³ to 13.08 x 10-2 m³. What is the efficiency of the process?

A particular thermodynamic cycle acting on a monatomic ideal gas (y = 1.67) includes an isobaric expansion, an isochoric cooling, and then a isothermic contraction. The PV diagram is shown in the image below. PA V The isobaric expansion occurs at a pressure of 1.8 × 105 Pa and changes the volume of the gas from 6.7 × 10 2 m³ to 13.08 x 10-2 m³. What is the efficiency of the process?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Kindly answer this basic thermodynamics question thank you
An ideal gas contained in a piston-and-cylinder device undergoes a thermodynamic cycle made up of three quasi-equilibrium processes. Step 1-2: Adiabatic compression from 330 K and 9.35 atm to 12.58 atm Step 2-3: Isobaric cooling Step 3-1: Isothermal expansion c.) Calculate Q, W, ΔU and ΔH, in J/mole, for each step in the process and for the entire cycle. Assume that CP = (5/2) R. d.) Is this cycle a power cycle or a refrigeration cycle? Explain. Calculate the thermal efficiency or COP of the cycle, whichever is appropriate.
Please solve this in thermodynamics
One cubic meter of oxygen at initial pressure of 1 bar and a temperature of17°C are compressed isentropically to a volume of 0.50m 3 . Use the specificheat at constant volume and pressure are 0.919 kJ/kgK and 0.659 kJ/kgK,respectively. Please answer the following a. The thermodynamic process the problem representsb. the pressure, temperature, and volume after the processc. change in internal energy, change in enthalpy and change in entropyd. work nonflow and heat transferred
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS. NO LONG EXPLANATION NEEDED. BOX THE FINAL ANSWER AND USE 3 DECIMAL PLACES. DRAW PV and TS Diagrams. SEE THE ATTACHED PHOTO FOR THE CONSTANTS. The gain in entropy during an isothermal non-flow process of 5 lb of air at 60°F is 0.462 Btu/R. What is (a) the ratio V2/ V1 (b) the ratio P2/P1 . (c) work in KJ and (d) heat in KJ?
2.5 liters of superheated steam at 25 bar and 400 C (V= 0.1252 m3/kg) is expanded in an engine to a pressure of 0.1 bar (Vg = 14.674 m3/kg, Vf = 0.0010102 m3/kg) when its dryness fraction is 0.9. Find the final volume(in liters) of the steam. Badly needed asap. I will rate helpful. Thank you in advance.
This example focuses on thermodynamics
Mollier Diagram: Steam Table Using the Steam Table below, find Δhf and Δhg in BTU/lbm and Δsf and Δsg in kJ/kgm-K and for the following parameters: P1 = 9.5 kgf/cm2 P2 = 15 kgf/cm2 NOTE: This table uses SI unit as stated below: Pressure: MPa Temperature: °C Internal Energy and Enthalpy: kJ/kgm Entropy: kJ/kgm-K
If 1 mole of ideal monoatomic gas experiments a reversible process in two stages, first isobar and then isotherm, which goes from 1atm and 20 ° C to 0.5 atm and 40 ° C. Determine the energy exchanged in the form of heat. Ans: AE = -609 cal/mol; W = 609 cal/mol; Q = 531.9 cal.
A dilute gas at a pressure of 2.0 atm and a volume of 2.0 L is taken through the following quasi-static steps. A. an isobaric expansion to a volume of 19.0 L B. an isochoric change to a pressure of 0.70 atm C. an isobaric compression to a volume of 2.0 L D. an isochoric change to a pressure of 2.0 atm Show these steps on a pV diagram. р (atm) p (atm) p (atm) p (atm) A D A D 2.0 2.0 2.0 2.0 D A В 0.70 0.70 0.70 0.70 C B C B V (L) V (L) V (L) V (L) 2.0 19.0 2.0 19.0 2.0 19.0 2.0 19.0 Determine from your graph the net work done by the gas (in J).
Thermodynamics Explain the relationships between systems constants for a perfect gas.
N = 0 An insulated tank of volume 10+(10+N)/25 m and with a valve was filled with perfect tri- atomic gas at pressure 10 bar, where N is equal to the last two digitals in your student's ID number. Initially the valve was closed. A paddle wheel was mounted inside the tank and was run by 20 kW engine. The paddle wheel was turn on and at the same time the exit valve was opened. The gas temperature was constant though the whole process (due to very slow flow) and equal to 300 K. Calculate the time needed to decrease the pressure in the tank to 5 bar.