A pin-connected truss composed of members AB and BC is subjected to a vertical force P = 40 kN at joint B (see figure). Each member is of constant cross-sectional area: AAB = 0.004 m2 and 2 ABC = 0.002 m2. The diameter d of all pins is 20 mm, clevis thickness t is 10 mm, and the thickness t1 of the bracket is 15 mm. Determine the normal stress acting in each member and the shearing and bearing stresses at joint C.

A pin-connected truss composed of members AB and BC is subjected to a vertical force P = 40 kN at joint B (see figure). Each member is of constant cross-sectional area: AAB = 0.004 m2 and 2 ABC = 0.002 m2. The diameter d of all pins is 20 mm, clevis thickness t is 10 mm, and the thickness t1 of the bracket is 15 mm. Determine the normal stress acting in each member and the shearing and bearing stresses at joint C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P1=58kN P2=80kN
Hi. Please help me with this one. Thank you very much. Subject: Theory of structures. MN= 104
Calculat reactions at pin support A and edge B, take beam weight 35 Kg 1 т 3 т B 50° A
2.54 The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap A between the lower end of the left rod and its pin support at C. After attachment, the strain in the left rod is 1.5 x 10-3. What is the length of the gap A? The cross-sectional areas are 300 mm? for rod AC and 250 mm² for rod BD. Use E = 200 GPa for steel. A B 0.75 m -1.5 m 2 m FIG. P2.53, P2.54
Resolve the 500N force into x- and y'-components
The rope AB exerts a 46 - N force T on the collar at A Let rCA be the position vector from point C to point A (Figure 1) Figure
Determine the reactions at the supports 30° 30 30° 30 10 10 10 10 600lb 900lb 600lb
A beam is subjected to equal bending moments of M₂ = 36 kip-ft. The cross-sectional dimensions are b₁ = 7.5 in., d₁ = 1.4 in., b₂ = 0.60 in., d₂ = 5.2 in., b3 = 3.2 in., and d3 = 2.4 in. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M₂ Z M₂ X Z b₂ H K b₁ y| d₂ d3
Static of Rigid Bodies Prob 03: Locate the centroid of the plane area shown: y 4 in. -8 in.-
A plane frame ABCDEFGH shown in figure has clamp support at A, hinge supports at G and H, axial force release (horizontal sleeve) at C and moment release (hinge) at E. The static (D,) and kinematic (D, ) indeterminacies are C B. E F oflot H G
D 4 m 2 m 1.5 m 2.5 m 2 m 1m 0.5 m B The assembly above consists of straight members forming a pyramid structure, as shown. The unit vectors for members AC and AD are as follows: UAc = {0.707i - 0.707j} • UAD = {0.530i + 0.848k} %3D Which of the following is closest to the angle between members AC and AD? a) 74.3° b) 1.19° c) 68.0° d) 90.4°
Force member CF is what? P= 78 kN Subject: Structural Theory