PROBLEM 4A pipe has a total length of 9800 ft with diameter of 30 in., and its thickness is 5/8 in. Assume that Ep = 30 x 10° psi,and Es = 300,000 psi. If the initial velocity for steady flow is 8 ft/s and a valve near the end of the pipe is partiallyclosed so as to reduce the flow to half of the initial velocity in 3 seconds,(a) What is the wave celerity (ft/s), and(b) find the maximum pressure rise (psi) from the water hammer.

Answered: Image /qna-images/answer/ed69b8d7-e16e-4902-a3fb-d0fd2f6fabc2.jpg

Answered: A pipe has a total length of 98 and Es…

Engineering

Civil Engineering

A pipe has a total length of 98 and Es = 300,000 psi. If the init: closed so as to reduce the flow

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000 ft long and 15-inch in diameter. The pipe is commercial steel with roughness 0.00015 ft. Water temperature is 50°F (kinematic viscosity is 1.41 x 105 ft?/s), and the total discharge is to be 4 ft /s? Use g = 32.2 ft/s?. Determine: The velocity, friction factor, and flow rate of water in pipes 1 and 2. (1) A B
In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000 ft long and 15-inch in diameter. The pipe is commercial steel with roughness 0.00015 ft. Water temperature is 50°F (kinematic viscosity is 1.41 x 10-5 ft2/s), and the total discharge is to be 4 ft /s? Use g = 32.2 ft/s². Determine: The velocity, friction factor, and flow rate of water in pipes 1 and 2. 2 Drag and Drop your answer below. A BI 三三EE II 125 !! ...
The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the tank is 0.028 m^3/ sec. Determine the minimum height, h, of the water tank under the assumption that (a) minor losses are negligible, (b) minor losses are not negligible. 3 m Figure No.3 Kentrance = 0.5 h The pipe is plastic of 15 cm diameter and (e/D=D0) 1.8 m (2) Main line 450 m with 15 elbows of 90 degree
Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B given a pipe diameter of 200 mm and the exit diameter to be 150 mm. Neglect losses of head.
3. If the velocity of flow in a 500mm diameter cast iron non - rigid pipe with modulus of elasticity of 8.30 GPa be changed in 0.25 second from 0.9 m/s to 0 m/s by closing a valve 300 m from a reservoir. If the pipe has a thickness of 20mm and bulk modulus of elasticity of water is 2.07 GPa, a. Determine the sonic velocity in the pipe. b. Determine the compressibility of the water.
A valve is suddenly closed in a 200 mmø pipe. The increase in pressure is 700 kPa. Assuming that the pipe is rigid and the bulk modulus of water is 2.07 x 109 N/m2 If the length of the pipe is 650 m. long, compute the water hammer pressure in kPa at the valve if it is closed in 3 sec.
Two tanks A and B have 80 m diffenence in water levels, and are connected by a pipe 0.3 m diameter and 8 km long with 0.002 friction coefficient. The pipe is tapped at its mid point to leak out 35 1/s flow rate. Determine the leaving tank А? discharge Find the discharge entering tank B? Coefficient (Tank Exit) = 0.5 %3D Coefficient (Tank Entry) = 1 %3D ha %3D A he 80 m Q1
Estimate the maximum water hammer pressure generated in a rigid pipe of a 3 m dia pipe with an initial velocity of 3.0 ms-¹ and the pipe is 8 km long. The downstream valve at the pipe end is closed in 4 seconds. The bulk modulus of water is 2.25x106 kPa and the mass density is 995.7 kg/m³. Also determine the critical time of closure.
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
i) Which of the following statements about a straight horizontal pipe of 6 inch diameter pressurized pipe carrying water is incorrect? i) The EGL and HGL are parallel to each other. ii) The friction head is equal to the loss in pressure head. iii) The velocity head gradually decreases from the beginning to end of the pipe. iv) The EGL (or) TEL is above the HGL. Answer: ii) Water flows from a 0.75 m pipe into a 1 m pipe. If losses are neglected then the 1 m diameter pipe will most likely (i) Have higher velocity than 0.75 m pipe (ii) Be at the same pressure as the 0.75 m diameter pipe (iii) Be at a higher pressure than 0.75 m pipe (iv) Be at a lower pressure than 0.75 m pipe. Answer:
The pressure gauges are inserted at A and B in a vertical pipe converging water. The diameters at A and B are 150mm and 75mm respectively. The point B is 2.3m below point A. When rate of flow down the pipe is 0.021m³/s. The pressure at B is 117.72 KN/m² greater than at A. The losses in pipe between A and B are expressed as(KVa²/2g) where Va is velocity of A. Find the value of K. If the pressure gauges at A and B are replaced by tubes filled with water and connectef to a u-tube containing Hg(SHg=13.6) calculate the value of the reading manometer.
An oil of viscosity 8 poise flows between two parallel fixed plates which are kept at 60 mm distance. The pressure drop over the length of 150 cm is observed to be 4.5 kPa. The width of the plates is 0.2 m. The discharge of flow (in Ips) is [Assume laminar flow.]