A pipeline with a pump carrying a 50 L/s discharge leads to a nozzle as shown. If the 180 mm diameter pipe is made of cast iron while the 120 mm diameter pipe is made of commercial steel. Determine the head of the pump using the energy equation from pt. A to pt. C. The fluid is water with a kinematic viscosity of 1.02 x 10-6 m³/s. El. 20 m Water B 180-mm dia. pipe 200-m long pipe 300-m long pipe 120-mm dia. pipe El. 10 m El. 30 m

A pipeline with a pump carrying a 50 L/s discharge leads to a nozzle as shown. If the 180 mm diameter pipe is made of cast iron while the 120 mm diameter pipe is made of commercial steel. Determine the head of the pump using the energy equation from pt. A to pt. C. The fluid is water with a kinematic viscosity of 1.02 x 10-6 m³/s. El. 20 m Water B 180-mm dia. pipe 200-m long pipe 300-m long pipe 120-mm dia. pipe El. 10 m El. 30 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Crude oil (with specific weight γoil = 55 lb/ft3 ) is pumped at a rate of 400 gallons per minute from a test separator at A to the stock tank shown using a pipe that has a diameter of 4 inches. The pressure at A (to the left of the pump or prior to the pump) is 4 psi and the stock tank is open to the atmosphere. The friction head loss along the entire length of the pipe from A to B is 45 inches. Note that 1ft3 = 7.48 gallons. (a) Determine the velocity in the pipe. (b) Determine the head gain, ℎ??, delivered by the pump to the flow. (c) Determine the power required to run the pump if it is 90% efficient.
Gasoline flows steadily downward through the pipe shown in the figure below. Viscous effects are negligible, and the pressure gage indicates the pressure is zero at point (1). Determine (a) the flowrate and (b) the pressure at point (2). (a) Q = (b) p2 = 2.0ft 3.5ft 18 -0.12 ft -0.1 ft -free jet ft³/s lb/ft²
Argon gas flows through a well-insulated nozzle at steady state. The temperature and velocity at the inlet are 570°R and 150 ft/s, respectively. At the exit, the temperature is 460°R and the pressure is 40 lb/in². The area of the exit is 0.0085 ft². Use the ideal gas model with k = 1.67, and neglect potential energy effects. Determine the velocity at the exit, in ft/s, and the mass flow rate, in lb/s.
The cyclindrical tank with hemispherical ends shown in Fig. contains a volatile liquid and its vapor. The liquid density is 800 kg/m', and its vapor density is negligible. The pressure in the vapor is 120 kPa (abs), and the atmospheric pressure is 101 kPa (abs). Determine: (a) the gage pressure reading on the pressure gage; and (b) the height, h, of the mercury manometer. Open Vapor 1m 1 m Liquid 1 m Mercury E E
Oil of SG 0.75 flows through the nozzle shown and deflects the mercury in the U-tube gage. What is the pressure at B in Kpa? A 2.75 D h B C Hg(13.6)
A 10 cm diameter solid cylinder of height 10 cm weighing 0.40 kg is immersed in a liquid (800 kg/cm^3) contained in a tall metal cylinder having a diameter of 13 cm. Before immersion, the liquid was 8 cm deep. At what level from the bottom will the solid cylinder float? W, = 0.40kg %3D 10cme tank New L.S. Original L.S F,
Oil (relative density or specific gravity of 0.8) flows through a pipe. the diameter is 50 cm. The length is 20 m, z1 is 1m and z2 is 2m. the speed is 4 m/second. the difference in heights in caliber is 1 cm. the caliber contains mercury and its density is 13600 kg/m3. Find the friction factor and determine whether the flow is laminar or turbulent. la viscocity of the oil is 0,319 Mt seg/m2
5. For the system shown in figure 12, calculate the: a.) volume flow rate of oil from the nozzle Oil (sg = 0.85) 3.0 m b.) the pressures at A and B. 35-mm diamete 100-mm inside diameter Flow B- -A+ 1.0 m
answer this please asap. this 30 mins left in the tank
In a given setup, distilled water flows towards the inside and goes outside of the vessel as shown in the figure. What is the rate of change of the water's mass (dm/dt) in the vessel? 3 in. Q = 0.3 ft3/sec V = 30 ft/sec Device m = 0.3 slug/sec %3D
A water supply tank is capable of providing 0.3 m³/s of water for fire fighting in a chemical plant. The water supply comes from a lake, the lake surface elevation is 800 m and the factory elevation is 852 m above sea level. The water discharge pipe is located at a depth of 100 m from the lake surface. The pipe friction losses to the plant are given by the ratio (0.01 m/s²).L, where L is the pipe length. The piping to the supply tank has an internal diameter of 0.15 m and a length of 8000 m. How much energy should a pump supply to water?
Castor oil (SG = 0.96) uiny Problem 9: %3D A tank whose bottom is 18 inches x 18 inches is filled with 2 in. three liquid as shown: 12 inches of carbon (SG=1.59), 4 inches of water and 2 inches of (SG=0.96). Compute the total hydrostatic psi) acting at the bottom of the tank. tetrachloride water 4 in. castor oil Carbon tetrachloride 12 in. pressure (in (SG = 1.59)