A piston-cylinder device initially contains 2 kg of refrigerant-134a at 100 kPa and 20°C. Heat is now transferred to the refrigerant from a source at 150°C, and the piston, which is resting on a set of stops, starts moving when the pressure inside reaches 120 kPa. Heat transfer continues until the temperature reaches 80°C. Assume the surroundings to be at 25°C and 100 kPa. R-134a 100 kPa 20°C 150°C Problem 08.048.a - Work Done by a Piston Device with Refrigerant Determine the work done. Use the tables for R-134a. (You must provide an answer before moving on to the next part.) The work done is [ KJ.

A piston-cylinder device initially contains 2 kg of refrigerant-134a at 100 kPa and 20°C. Heat is now transferred to the refrigerant from a source at 150°C, and the piston, which is resting on a set of stops, starts moving when the pressure inside reaches 120 kPa. Heat transfer continues until the temperature reaches 80°C. Assume the surroundings to be at 25°C and 100 kPa. R-134a 100 kPa 20°C 150°C Problem 08.048.a - Work Done by a Piston Device with Refrigerant Determine the work done. Use the tables for R-134a. (You must provide an answer before moving on to the next part.) The work done is [ KJ.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please help! Thank u! 3. Consider the following systems. a) What is the heat capacity of a system consisting of a 0.870-kg brass cup filled with 0.0500 kg of water? Specific heats of brass and water at 1.00 atm and 20.0°C are 0.384 kJ/kg•K and 4.186 kJ/kg/K respectively. b) What is the heat capacity of a system consisting of 8.10 kg of water in a 0.310-kg aluminum bucket? Specific heats of aluminum and water at 1.00 atm and 20.0°C are 0.900 kJ/kg-K and 4.186 kJ/kg:K respectively.
! Required information Problem 08.034 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS - Refrigerant Constant Pressure System NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A piston-cylinder device contains 6 kg of refrigerant-134a at 0.7 MPa and 60°C. The refrigerant is now cooled at constant pressure until it exists as a liquid at 20°C. The surroundings are at 100 kPa and 20°C. Problem 08.034.a - Exergies of Refrigerant Constant Pressure System Determine the exergy of the refrigerant at the initial and the final states. Use the tables for R-134a. (You must provide an answer before moving on to the next part.) The exergy of the refrigerant at the initial state is The exergy of the refrigerant at the final state is [ kJ. kJ.
14. Air is contained in a piston - cylinder arrangement. The following data were gathered: P= 700 KPa,V -010 m/kg.m, and u, = 160 KJ/kgm. The air expands slowly with the pressure remaining constant until the specific volume becomes, V2= 0.20 m³/kg. and the internal energy becomes, u2 = 310 KJ/kgm- Calculate the work done by the gas and the heat transferred.
It is a hot day in Atlanta and you and your friends bought an ice cream maker. The unit consists of a bowl and a base that rotates the bowl around a stationary mixing paddle. The walls of the bowl contain an unknown mixture that absorbs heat from the ice cream. The bowl must be frozen (-20°C) before use. Unfortunately, your friends have lost the instructions and can't remember how long to operate the unit. You tell them not to worry since you have mastered energy conservation problems and can calculate the amount of time required to freeze the ice cream. Looking at the box, you find the specifications for the unit: a) Inner surface area of freezing bowl: 600 cm2; b) Heat transfer coefficient for bowl:h = 0.025 J / (cm2 s .°C); c) Power required to stir the bowl (100% efficiency):25 W; d) Amount of ice cream mixture added: 1 kg; e) The rate of heat transfer is between the bowl and the milk. You know that solutes lower the freezing point of water. Assume that the freezing point is…
! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A piston-cylinder device initially contains 1 kg saturated liquid water at 200°C. Now heat is transferred to the water until the volume quadruples and the cylinder contains saturated vapor only. The saturated liquid properties of water at 200°C 3 are vf= 0.001157 m³/kg and uf- 850.46 kJ/kg (Table A-4). Water mkg 200°C Q Determine the final temperature and pressure. (You must provide an answer before moving to the next part) The final temperature is The final pressure is °C. kPa.
1. A steel flask of 0.04 m³ capacity is used to store Nitrogen at 120 bar and 20°C. The flask is protected against excessive pressure by a fusible plug which will melt and allow the gas to escape if the temperature is too high. A. How many kilogram of Nitrogen will the flask hold at the design conditions? B. At what temperature in °C must fusible plug melt in order to limit the pressure of flask to a maximum of 150 bar?
1. Propane (MW = 44 ; k = 1.13) initially at 30 psia and 215°F, is stored inside a large spherical vessel having a diameter of 10 ft. If the temperature is increased to 635°F. Determine the following: a. Final pressure; 48.6667 psi b. Mass of propane; 95.4339 Ibm c. Constant Volume Specific heat; 0.3472 BTU/lbm.R d. Change in Internal Energy, AU; 13915.6961 BTU
10. Methane enters a compressor at 14 psia with a very low velocity and is compressed to 55 psia. The entering methane has a density of 0.04 lb /ft. The methane leaves the compressor with a velocity of 250 fps. The flow rate is 0.38 lb/s. Assuming a quasi-equilibrium process in which pu133=constant, calculate the work done on the methane in hp. m m [ans: -57.4 hp] to Thermodynamics
Required information Problem 04.038 - Energy balance for water in a piston-cylinder device NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. An insulated piston-cylinder device contains 3.5 L of saturated liquid water at a constant pressure of 175 kPa. Water is stirred by a paddle wheel while a current of 8 A flows for 45 min through a resistor placed in the water. One-half of the liquid is evaporated during this constant-pressure process and the paddle-wheel work amounts to 400 kJ. 11,0 consta Problem 04.038.a - Find source voltage Determine the voltage of the source. Use data from the steam tables. (Please provide an answer before moving on to the next part) The voltage of the source is V.
Task 5A sample of gas is compressed by an average pressure of 2 atm which decrease its volume from400 cm 3to 200 cm 3. During the process, 10 J of heat is rejected to the surroundings. Explain and demonstrate the application of the first law of thermodynamics to this system and calculatethe change in energy of the system.
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS. NO LONG EXPLANATION NEEDED. BOX THE FINAL ANSWER AND USE 3 DECIMAL PLACES. DRAW PV-TS Diagrams. A scuba tank contains 1.5 kg of air. The air in the tank is initially at 15°C. The tank is left near an engine exhaust line, and the tank's pressure doubles. Determine (a) the final temperature; (b) the change in internal energy; (c) the heat added. (d) ΔS. please see the image attached for the constants
1. A rigid contained fitted with a 200 W resistive heater contains 4 Ibm of N2 (nitrogen). Initially, the gas is at T1 = 47°C and P1 = 1.25 bar. The heater is turned on for 30 minutes. During this time, the container is found to transfer roughly 50 kJ to its surroundings via natural convection. The mass and volume of the heater can be neglected. Assuming the N2 can be modelled as an ideal gas, determine: a. T2 (°C) b. P2 (bar) C. Whether the ideal gas model a good approximation of the system. Show your justification.