A platinum RTD PT100 measures 100 Q at 0 °C and 139.1 Q at 100 °C. Calculate temperature in °C if Temperature Coefficient of RTD PT100 is given as 0.0066 and resistance is 105.2(Q). O 7.16 7.88 10.91 O 8.04

A platinum RTD PT100 measures 100 Q at 0 °C and 139.1 Q at 100 °C. Calculate temperature in °C if Temperature Coefficient of RTD PT100 is given as 0.0066 and resistance is 105.2(Q). O 7.16 7.88 10.91 O 8.04

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: I, 60/0° V +1 j15 Ω j100 Ω m j50 Ω j0 Ω ell 80 Ω j 10 Ω 40 Ω-j20 Ω ww j80 Ω +1 1, 20/90° V Find 11,…

A: Detailed solution is attached with the notes.please go through and follow up in case of queries.…

Q: 2 -1 0¹ w(t) Figure Q1(b) 2

Q: What are rotor faults in alternators

A: The rotor of an alternator is directly connected with field winding of the alternator whenever there…

Q: 19 A balanced three-phase voltage source, Van = 200/0° V rms, positive phase sequence, is connected…

Q: 16.a. Receptacle outlets shall be installed so that no point along the floor line in any wall space…

A: Answer 16 (a): According to article 210.52(A) General Provisions, Receptacle outlets must be…

Q: 1. Using Norkons resistor of ike 40v Theorem network Shown Find the Current below 4.5 62 52 A $. B…

Q: Given the AC Bridge, determine the phase angle of Z4 (in °), if the values of other impedances are:…

Q: A voltage divider amplifier shown in Figure 3 has an output current Ic = 4 mA. Based on the circuit…

A: Since you have posted the questions with multiple subpart so we are supposed to answer 3 subpart.

Q: Compute for the current flowing at Z2 using nodal and mesh analysis. Answer must be in polar form.

Q: For this circuit Is and V2 = R1 1Q Is R2 20 wwwwww V2 +Vs 12 V Select one: O a. Is = 1 A, V2= 2 V O…

A: Given circuit:

Q: Multiplexer 32 to 1 has 3 Selectors O 1 Selector O2 Selectors 5 Selectors

A: Given, A 32:1 multiplexer.

Q: An R−L−C series circuit has a current which lags the applied voltage by 45°. The voltage across the…

Q: Point a is on the +y-axis at y = +0.200 m and point b is on the +x-axis at x = +0.200 m. A wire in…

A: (a) It is given that the a quarter circle piece of wire carries a current of I=5 A from the…

Q: In the series RL circuit of figure shown, the sinusoidal source is given by v = 100 sin (500t + )…

Q: If A = 1001 1001 0000 0010, show the result of the logical shift right operation in hex

A: If A = 1001 1001 0000 0010, here we have to show the result of the logical shift right operation in…

Q: Q1. Using the concepts delivered in Maxwell's equation, develop an explanation of uniform plane wave…

A: All four equations of Maxwell in the phasor form are shown below:…

Q: (b) at the edge of saturation (c) deep in saturation with forced = 10 For simplicity, assume that…

Q: Inverse Laplace Y(5) 2 4(+) (S+5) 5 (50+35+7) (5+4 ) с

A: given Ys=ss+5s2+3s+2s2+4 by partial fraction Ys=ss+5s2+3s+2s2+4=As+2+Bs+1+Cs+Ds2+4…

Q: balanced delta connected load has one phase current Ibc=2 angle -90 degree A. Find the other phase…

Q: Discuss the following: i) Distance relay ii) differential relay iii) overcurrent relay

A: Given, Discuss :- i) Distance relay ii) Differential Relay…

Q: Vamp R Vout Figure 2: RLC circuit in a speaker system. The circuit has an input AC voltage with…

Q: Find the value of the v across 6H 120 cos co V 10 H sm OF -OV

Q: a) Determine the node voltages using nodal analysis. 5V 1000 ww 10 V A 5009 www € 800 Figure 2 IV…

Q: 9. If the output voltage of an amplifier is 1.2 V rms and its voltage gain is 50, what is the rms…

Q: 40/60° V +1 2 Ω ww 16Ω -j4Ω Η j8 Ω 1:2 -j12 Ω FIND the value of Vı and Vá and Io. Topic:…

A: Given circuit with magnetically coupled coils of voltage ratio 1:2. To find V1, V2 and I0

Q: A 3-bit quantiser has a dynamic range of ±4 Volts. How many quantisation levels could this system…

A: Given, Number of bit in quantiser, n=3 Dynamic range, ±4 V

Q: b. An AM transmitter is modulated by five different tones at 1.5 kHz, 3 kHz, 4.5 kHz, 6 kHz and 7.5…

A: Given data, An AM transmitter is modulated by five different ones at f1=1.5 kHzf2=3 kHzf3=4.5…

Q: What is the value of this resistance in ohms of a 4-band resistor with color combinations of…

Q: For the below IC 555 configuration, pulse duration will be? 5 ΚΩ 6 μF Trigger Input 6 7 2 8 1 4 5 3…

A: Given circuit, R=5 kΩC= 6 μF

Q: Fill-In Questions: 1. A forward-biased 2. A reversed-biased diode has_ diode has resistance.…

Q: a) Use two input AND and two input OR gates to realize the function. b) Convert the circuit to…

A: For AND gate, When the all inputs are high then only the output of AND gate is high and remaining…

Q: . A system is in the following input-output relationship. y(t) = x(t)x(t − 1) Prove that the system…

A: GIVEN: y(t)=x(t)× x(t-1) FIND: linearity time-invariant causality…

Q: An inductance of 2 henries and a resistancc of 20 ohms are connected in series with an emfE volts.…

A: E=100 V DC Find i (t=0.01)

Q: In the circuit given below, R= 30 Q. Find vo and lo 50 2 10 Q2 www ww % 250 V io 10Ω 0.2% + The…

A: The circuit diagram is shown below, Where,R=30 Ω

Q: (4) Consider an FM signal given by the expression f(t) = cos[2nfet + ß₁ sin(2πf₁t) + B₂ sin(27f₂t)].…

A: Frequency modulation :- It is a technique that encodes information on particular signal by changing…

Q: 2. Using the Illustration below. Compute the total impedance (Z), the total current (1), the voltage…

Q: 7) For the sequence {1, 0, 1, 0}, IDFT will be None of the above O {0.5, 0, 0.5, 0} {1, 1, 0, 1}…

A: For the given discrete fourier transform sequence we need to calculate their inverse discrete…

Q: In an attempt to boost DC voltage, two students thought of using a transformer to accomplish such…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: For the circuit shown, find the voltage drop in each resistance using Kirchhoff's Law 1092 150 5V +…

Q: Find Ic, Ib, Vce, Vc, Vb, Vrc,Vrb for all the CE amplifier Show the solution and Draw the DC load…

A: For the above given NPN transistor circuit we need to derive all the DC parameters.

Q: 1. Find the values of I and V in the circuit shown below for the following cases: (i) Assuming the…

A: As per our guidelines we are supposed to be the first three questions only. Kindly repost the other…

Q: V, is a 60Hz source with a peak voltage VP-120V is feeding a rectifier, assume ideal diode. The load…

Q: Which of the following statements about next-generation wind energy is correct? a. They will have a…

Q: FIND V(t) Y/₁₂F= + 32H શો નૈન V(t) + 4 cos (3+ +150) 34H Ssin(St) (+-)

Q: A 15.0 uF capacitor is charged by a 150.0 V power supply, then disconnected from the power and…

A: Given data, The value of capacitor (C) is15μF = 15×10-6 F, The value of the inductor (L) is 0.280mH…

Q: An AM transmitter uses high-level modulation of the final RF power amplifier, which has a dc supply…

A: Given data, Supply voltage Vcc=36 V Current I = 2.8 A Efficiency η=77%

Q: 31. For the circuit of Figure 5.71, determine the Thévenin equivalent that drives the 20 nF…

A: Given circuit :

Q: H3. (Dynamical System ) Explain various types of oscillator in non linear system

A: Nonlinear oscillator : Whenever a force is exerted on any particle then there is movement in the…

Q: b) Considering the average input voltage found in (a), what will be the minimum value of R₂?

A: Given data, The maximum Zener current (Izmax)=100mA The maximum Zener Power dissipation (Pz)=1W The…

Q: An impulse generator has eight stages with each condenser rated for 0.16 µF and 125 kV. The load…

Concept explainers

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.

Question

A platinum RTD PT100 measures
100 Q at 0 °C and 139.1 Q at 100 °C.
Calculate temperature in °C if
Temperature Coefficient of RTD
PT100 is given as 0.0066 and
resistance is 105.2(0).
O 7.16
O 7.88
O 10.91
O 8.04

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 58 V and the firing angle of the SCR is 135 degrees, the RMS voltage at the output would be: O A. 98 V O B. None of the other choices are correct O C. 266 V O D. 399 V O E. 133 V
In a half wave rectifier, the input sine wave is 300 sin 100 TTt Volts. The average output voltage is a. 31.4 V b.95.54 V C. 102.52 V d. 150 V
A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 74 V and the firing angle of the SCR is 60 degrees, the RMS voltage at the input would be: O A. 220 V O B.99 V O C. None of the other choices are correct OD. 110 V O E.256 V
The power output of the half-wave rectifier is rated at 102.4 W with a load resistor of 40 ohms. The RMS voltage at the output is: O A. None of the other choices are correct O B. 12.5 V O C. 102 V O D. 25.5 V O E. 51 V
In a half wave rectifier, the sine wave input is 300sin300t. The average value of output voltage is? a. 67.453V b. 95.492V c. 63.694V d. 57.876V
The input to a full-wave rectifier is 20 V AC (RMS). The load resistor is 20 ohms and rectifier losses are 4W. The ripple factor of the rectifier is: O A. 0.96 OB. 0.33 O C. 0.48 O D. None of the other choices are correct O E. 0.75
A 1 - ∅ full-wave rectifier is made by using thyristors. If the peak value of the sinusoidal input voltage is Vm and the value of the delay angle is 45 degree, find the average value of output voltage Select one: a. 0.65 VM b. 0.85 VM c. 0.45 VM d. 0.25 Vm
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
What types of PWM is shown in the figure? * Modulating Waveform Carrier waveform A (b) 44444 F -V O Unipolar O Bipolar 000
Calculate the value of the capacitor in the full wave rectifier filter as shown below. Knowing that the ripple percent is 5%. 10.1 130 V Ouepon 750 uF O 1000 uF O 660 uF O 2200 uF Other value O
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to c 20:5A L VI-DC20V 220V omsh T 0.01 F 0.02 F 0.0167 F None of the above euer
FAIRCHILD Discrete POWER & Signal Technologies SEMICONDUCTOR ru 1N4001 - 1N4007 Features • Low torward voltage drop. 10 a14 * High aurge eurrent cepablity. 0.160 4.06) DO 41 COLOR BAND DGNOTEs CAT-Cos 1.0 Ampere General Purpose Rectifiers Absolute Maximum Ratings T-26*Cuness atnerwioe rated Symbol Parameter Value Units Average Recttied Current 1.0 375" lead length a TA - 75°C Tsargei Peak Forward Surge Current 8.3 ms single halr-sine-wave Superimposed on rated load JEDEC method) 30 A Pa Total Device Dissipetion 2.5 20 Derste above 25°C Ra Tag Thermal Resistence, Junction to Amblent 5D Storage Temperature Range 55 to +175 -55 to +150 Operating Junetion Temperature PC "These rarings are imithg valuee above whien the serviceatity or any semiconductor device may te impaired. Electrical Characteristics T-20'Cunieas ofherwise roted Parameter Device Units 4001 4002 4003 4004 4005 4006 4007 Peak Repetitive Reverse Vellage Maximum RME votage DC Reverse Voltage Maximum Reverse Current @ rated VR…