A point within an embankment slope has a vertical normal stress (O) of 100 kPa, a horizontal normal stress (Ox) of 60 kPa, and a horizontal shear stress (Txy) of 20 kPa. (a) Determine the major and minor principal stresses. (b) Determine the orientation of the major principal stress (in degrees from vertical, clockwise, or counterclockwise. (c) Draw the Mohr Circle and schematic of the element stress state.

A point within an embankment slope has a vertical normal stress (O) of 100 kPa, a horizontal normal stress (Ox) of 60 kPa, and a horizontal shear stress (Txy) of 20 kPa. (a) Determine the major and minor principal stresses. (b) Determine the orientation of the major principal stress (in degrees from vertical, clockwise, or counterclockwise. (c) Draw the Mohr Circle and schematic of the element stress state.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Similar questions

The vertical compressive stress at a point in a soil is 100 kN/m2 while the horizontal compressive stress at the same point is 62 kN/m². Both stresses are principal stress. (a) Draw the Mohr circle that describes the 2D stress state at the point (hand sketch is ok). (b) Find the maximum shear stress that acts at the point. (c) Determine the angle of the plane on which the maximum shear stress acts and obtain the normal stress on that plane (Use the pole method - the method is simplified since the stresses given in the problem are principal stresses). (d) Confirm the maximum shear stress and the normal stress from (c) using the stress transformation equations (consider sign conventions!).
Using Mohr's Circle Determine: a.) The principal planes and directions b.) The principal Stresses and directions c.) The maximum Shear stress and the corresponding normal stress and directions 10 MPa 40 MPa 0 50 MPa
determine the maximum shear stress. sketch thesection stress distribution
10-16. A 1 m cube within a mass of stressed soil has a stress of 100 kPa on its top and bottom faces, 50 kPa on one pair of vertical faces, and 30 kPa on the other pair of vertical faces. There is no shear stress on any face. Fill in the numerical values for each stress and angle in the following table. (After Taylor, 1948.) o(kPa) 7(kPa) a Major principal plane: Intermediate principal plane: Minor principal plane: Plane of maximum shearing stress: Plane of maximum obliquity: Note: a is with respect to the horizontal plane.
The vertical compressive stress at a point in a soil is 100 kN/m2 while the horizontal compressive stress at the same point is 57 kN/m2. Both stresses are principle stress. (a) Draw the Mohr circle that describes the 2D stress state at the point. (b) Find the maximum shear stress that acts at the point. (c) Determine the angle of the plane on which the maximum shear stress acts and obtain the normal stress on that plane (Use the pole method). (d) Confirm the maximum shear stress and the normal stress from (c) using the stress transformation equations (consider sign conventions!).
Find the vertical stress increment at this point of interest using Boussinesq analysis.
Problem 6. [Concepts: Spatially varying average normal stress, and integration] The bar has a cross-sectional area of 400(106) m². If it is subjected to a triangular axial distributed loading along its length which is 0 at x = 0 and 9 kN/m at x = 1.5 m, and to two concentrated loads as shown in the figure. a) Determine the average normal stress in the bar as a function of x for 0
At a point P, the rectangular stress components are: x = 1, y = -2,0 = 4, y = 2, T = -3 and T = 1 yy all in units of kPa. Find principal stresses and check for invariance.
A) Show the following on Mohr's stress circle: 1-The value of direct stress in the plane of the maximum Shear stress. 2-The angle of the maximum shear stress. 3-The value of the shear stress on the principal plane. B) The direct stresses in two mutually perpendicular directions are 50 MN/m² (compressive) and 200 MN/m² (tensile) accompanied by shear stresses of intensity 100 MN/m² clockwise on effect on the plane carrying 200 MN/m² stress. Using Mohr's Stress Circle, find the principal stresses, maximum shear stress, and their planes, the normal and tangential stresses on plane inclined 30 clockwise to the planes of the 50 MN/m² direct stresses. What is the shear stress which acting alone that produce the same maximum principal stress.
The stresses at a point are measured as shown. Using Mohr's circle determine the stresses with respect to x' - y' axes. Also, determine the maximum possible shear stress at this point. „3.5 MPa 18° '4.4 MPa
2. The following square section is subjected to an unsymmetric bending moment M=850 Nm, as shown. Compute the stresses at each of the 4 outer corners of the section, and sketch a 3D distribution of the stresses 2 B M=850 Nm mm 260 E 25 A D 250 mm REQ'D - stress at each corner - 3D stress distribution
Consider a point in a structural memberthat issubjected to planestress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S-45 MPa,S,-67 MPa, andS-21MP., (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses and the maximum in-planeshear stress acting at the point. (c) Show these stresses on an appropriate sketch (e.g. see Fig. 12.15 or Fig 12.16). (d) Determine the absolute maximum shear stress at thepoint Sy Determine the principal stresses and the maximum in-plane shear stress acting at the point. Say Answer: MPa MPa MPa Tomaxin plane