A rectangular cantilever beam has a width of 300mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The nominal moment capacity multiplied by its strength reduction factor is 334kN.m. Determine the allowable concentrated live load in kN that it could carry acting at 2.89m from the support if the length of the beam is 2.24m. Note that the dead load includes the weight of the beam.

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the fric...

A:

Q: Using Transit Rule and Compass rule, solve for the adjusted distance of line DE. LINE BEARING DIST...

A:

Q: A rectangular tension member is used resist a dead load of 85 kN and a live load of 200 kN. Use Fy =...

A:

Q: A beam is subjected to equal 19.6 kip-ft bending moments. Assume t1 = t2= tw= 1 in., d = 13 in., b1 ...

A:

Q: Define Designing for Flexure

A: The process of bending is known as flexure.  

Q: 12 kN P N. 4 m 12 kN M K L. F 4 m 32 kN H. 6 m DX E - 10 m -- tom 10 m --| 16 m 16 m

A:

Q: In a certain situation it was estimated that 24.9% of the braking force was applied to the rear brak...

A: Given data - Total braking force = 5565N U = 0.6 Width of wheel base = 295 cm CG ABOVE THE PAVEMENT ...

Q: 3. Water flows at the rate of 5 ft/s through an inclined pipe. At point A, where the diameter is 12 ...

A:

Q: Ap 1 m 2.5 m B 8 m

A:

Q: A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The...

A:

Q: draw the orthographic projection includes the views from the front, top, and left of the object. The...

A:

Q: Define Development Length

A: Thedevelopment lnegth term is used in design of R.C.C. structures.

Q: Pipelines 1, 2, and 4 are connected in series, while pipelines 2 and 3 are connected in parallel. Th...

A:

Q: For the given data of a transit-tape survey. Show all computations. 1. Determine the latitudes and d...

A:

Q: A course sand sample is placed in the constant permeameter test. What is the coefficient of permeabi...

A:

Q: a.)On a map of scale 1cm = 50m with a contour interval of 1.5m,two adjacent contour lines are 1.37cm...

A:

Q: A pipe 800 m long connects two reservoirs whose level difference is 60 m. Find the discharge in pipe...

A:

Q: The pin at C has a diameter xx(see table below). Assume that the pin supports at C is stated at the ...

A:

Q: Test the consistency of the 22 years of data of the annual precipitation measured at station A. Rain...

A:

Q: A rock sample of 35" is collected as shown below The RQD of the rock sample is most likely in % Core...

A:

Q: Group of answer choices a. 1 b. 2 c. 0.5 d. 0 The angle of rotation at the maximum deflec...

A: i) Slope at fixed support ii) Angle of rotation at maximum deflection  

Q: A tension member with an allowable tensile stress of 0.6Fy is connected to the gus using four rivets...

A: According to given data  A tension member with an allowable tensile stress of 0.6Fy is connected to ...

Q: -concrete rod with a cross-sectional area of andidate concretes are: (a) a=lmm, p=porosity=10% eterm...

A: According to given data  A concrete rod with a cross-sectional area of 10 cm2 is loaded in tension. ...

Q: Mark the correct statement: a) The ISC steps are: Compaction, Expansion and Simple Axial Compressio...

A: The correct statement is (C) The MR Resilience Module can be performed in a triaxial cell and dynami...

Q: 1. A composite axial structure consists of two rods joined at flange B. Rods (1) and (2) are attache...

A:

Q: c kN/m CO "b" m "b m IGURE 3

A:

Q: Test the consistency of the 22 years of data of the annual precipitation measured at station A. Rain...

A: step 1 ) FIRST ARRANGE ALL  GIVEN DATA IN REVERSE CHRONOLOGICAL ORDER ( THE LATEST RECORD AS THE FIR...

Q: Question No 1: Classify the y-coordinate of the centroid of the shaded area. Analyze_the shift of va...

A:

Q: For a simply supported beam with a sloping load line (y = mx) that starts at 0 kN/m on one end of th...

A:

Q: Determine the average annual rainfall overt the watershed. ATTACH YOUR SOLUTION: There are 10 rainga...

A: GIVEN : No . of Rain gauge Stations = 10 STATIONS  CO-ORDINATES  ANNUAL RAINFALL (cm) 1 (0,40) ...

Q: Each of the hydrological cycle involves the following except: - Temporary storage - transportation o...

A:

Q: This presentation is used in getting the magnitude of a storm in a particular duration in chronologi...

A: Option C is correct  Mass curve of rainfall.  

Q: m 2.5 m B 8 m

A:

Q: 50ka 100kw 25tN/m 5m

A:

Q: Draw the CPM diagram using Activity on Nodes (AON) and Activity on Arrows (AOA) and solve for the cr...

A: Step: 1 Critical path method (CPM): - It is defined as longest path in network diagram and also kno...

Q: The liquid in Fig. D has a specific gravity of 3.67. The gage pressure Pa = 10.67 Ib per sq in. and ...

A:

Q: For a given watershed, the initial infiltration capacity is 3.0 mm/hr and the equilibrium infiltrati...

A:

Q: The total discharge (flowrate) of water from into A and out of B (from left to right) in the figure ...

A: Determination of Friction factor , Head loss and discharge through pipe 1 and pipe 2##  

Q: Determine the force in each member of the truss shown.

A:

Q: The speed of water flowing in a channel, such as a canal or river bed, is governed by the Manning Eq...

A: Given, A = 1925 ft2 S = 0.05 P = 102.4 ft n = 0.030

Q: Calculate the total sound pressure level of multiple sound sources: 55 dB, 68 dB, 25 dB, and 50 dB c...

A:

Q: A 1 m 2.5 m 8 m

A:

Q: Hair Readings(m) angle(°) Upper | Middle | Lower 1.200 Vertical Position of Rod Rod held at A 15.58 ...

A:

Q: There are 10 raingauge stations available to calculate the rainfall characteristics of a catchment w...

A:

Q: 426 mn

A: Given:- rock sample =35" To find:- RQD  

Q: Compute the average rainfall using the Isohyetal Method A1= 250sq.m , P1=36 10 P1 A2= 198 sq.m, P2= ...

A:

Q: On a map drawn to scale of 1cm = 20m, the horizontal map distance between 1/2 m contours on a unifor...

A:

Q: fixed support?

A: Slope at the fixed support is zero

Q: During your experiment, you collected 2 data points in the fully submerged case. For the purposes of...

A:

Q: dz P (2) (1) B ミ→

A:

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.