A rigid body is made of two identical thin rods of mass M and length L fasted together in the form of a letter F. It is pivoted about a horizontal frictionless pin through one end as shown in figure below. The body is released from rest in the position A. At the instant the body is in the position B find the angular acceleration? A 2L 3 B Pivot

A rigid body is made of two identical thin rods of mass M and length L fasted together in the form of a letter F. It is pivoted about a horizontal frictionless pin through one end as shown in figure below. The body is released from rest in the position A. At the instant the body is in the position B find the angular acceleration? A 2L 3 B Pivot

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows the cross section of a uniform 239-lb ventilator door hinged about its upper horizontal edge at O. The door is controlled by the spring-loaded cable which passes over the small pulley at A. The spring has a stiffness of 16.6 lb per foot of stretch and is undeformed when 8-0. If the door is released from rest in the horizontal position, determine the maximum angular velocity reached by the door and the corresponding angle 0. Answer: @max 4.2¹ rad/sec at 8-i
The spool has mass, m, and a radius of gyration kG. An inextensible cord is attached to the wall at A. The cord is wound around the radius R and the outer radius 2R. The coefficient of friction between the spool and the ground is mu. What it the critical force, Fcrit (force required to cause motion) applied at point B? If force= 2Fcrit what is the linear acceleration of the center of mass? If force= 2Fcrit what is the tension in cord AC?
The stepped roller in the rack is released from rest. The rope attached to the wall is tied to the 50 kg pulley as shown in the figure. Find the angular acceleration of the pulley. The reel plane rolls without slipping. The gyration radius k for the reel is given above 0.5 m.
3. The spring-toggle system is in the vertical plane and is held at rest with 45° when a moment of 12 N-m is applied at point C. In the initial position, the spring, with stiffness of 140 N/m, is stretched 150 mm. Bar AB has a mass of 3 kg, and bar BC has a mass of 6 kg. Find the angular velocity of BC at the moment when 8-0. Neglect friction effects. 250 mm 250 mm OB 250 mm
A shaft has three eccentrics of mass 1kg each. The central plane of the eccentrics is 50 mm apart. The distances of the centers from the axis of rotation are 20 mm, 30 mm, and 20 mm and their angular positions are 120 degree apart. Find the amount of out-of-balance force and couple at 600 rpm. If the shaft is balances by adding two masses at a radius of 70 mm and at a distance of 100 mm from the central plane of the middle eccentrics, find the amount of masses and their angular positions. (Use graphical method for solution)
In the mechanism illustrated in the figure opposite, each of the two bars AB and BC has a mass of 10 kg. A constant torque of M = 100 N*m is applied to bar AB around point A. Both bars are initially at rest at the position shown. Neglect the size of the small roller at point C. a) Prove that the bar BC is in translational motion at the instant shown. b) Determine the horizontal and vertical reaction forces at point B and the vertical reaction force at point C. Answers: b) Bx = [83.34 N →]; By = [17.8 N 1] et Rc = [80.3 N ↑] 0.9 m B M 1.2 m C
The rope shown in the figure below is wound around a cylinder of mass 4.0 kg and I = 0.020 kg m2, about the cylinder axis. If the cylinder rolls without slipping, what is the linear acceleration of its center of mass? What is the frictional force? Use an axis along the cylinder axis for your computation. What happens if the frictional force between table and cylinder is negligible? Choose any axis for your computation.
Your answer is partially correct. The figure shows the cross section of a uniform 174-lb ventilator door hinged about its upper horizontal edge at O. The door is controlled by the spring-loaded cable which passes over the small pulley at A. The spring has a stiffness of 12.7 lb per foot of stretch and is undeformed when = 0. If the door is released from rest in the horizontal position, determine the maximum angular velocity reached by the door and the corresponding angle 0. Answer: Wmax = www 4.2' 0.636 rad/sec at 0 = 58.49 O
In a four bar mechanism the link AB rotates with angular velocity of 20rad/s and angular acceleration of 100 rad/s both in clockwise direction when it make an angle of 45° with link AD which is fixed .The length of various linkages are AB=CD=400 mm,BC=500mm and AD=750mm .Neglect the gravitational effect and friction.The mass of link is 5kg/m. Find the torque on output link E (2) (4) A (1) (1)
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
A stepped cylinder has the dimensions R₁ = 0.30 m, R₂ = 0.65 m, and the radius of gyration, k, is 0.35 m. The mass of the stepped cylinder is 100 kg. Weights A and B are connected to the cylinder. If weight B has a mass of 80 kg, and weight A has a mass of 50 kg, how far does A move in 5 seconds? In which direction does it move? (Draw all FBDs)
2. Consider the 5-1lb bar with length of 2½ feet and width of 2 inches. Small frictionless bearings are mounted to the ends, constraining the motion of the bar to the horizontal x and y slots. The bar starts at rest at positioned at 0= 45°. If an angular acceleration of 3 rad/s² is desired, what moment M must be applied to the bar? What are the reaction forces at A and B at that instant? Additional question: Does the width of the bar matter, or is it appropriate to consider the bar as a slender rod? Consider errors of less than 2% negligible.