A rigid tank whose volume is 0.5 m³, initially containing ammonia at 20°C, 1.5 bar, is connected by a valve to a large supply carrying ammonia at 12 bar, 130°C. The valve is opened only as long as required to fill the tank with additional ammonia, bringing the total mass of ammonia in the tank to 136.7 kg. Finally, the tank holds a two-phase liquid-vapor mixture at 20°C. Determine the heat transfer to the ammonia in the tank from the surroundings, in kJ, ignoring kinetic and potential energy effects. Qw = ! kJ

A rigid tank whose volume is 0.5 m³, initially containing ammonia at 20°C, 1.5 bar, is connected by a valve to a large supply carrying ammonia at 12 bar, 130°C. The valve is opened only as long as required to fill the tank with additional ammonia, bringing the total mass of ammonia in the tank to 136.7 kg. Finally, the tank holds a two-phase liquid-vapor mixture at 20°C. Determine the heat transfer to the ammonia in the tank from the surroundings, in kJ, ignoring kinetic and potential energy effects. Qw = ! kJ

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1: An air receiver contains air at 16 bar and 42°C. A valve is opened and some air is allowed to blow out to atmosphere. The pressure of the air in the receiver drops rapidly to 12 bar when the valve is then closed. Assuming that the mass in the receiver undergoes a reversible adiabatic process, calculate the initial and final mass of air if you know that the amount of air which has left the receiver is 18.04 kgs.
Two vessels A and B of different sizes are connected by a pipe with a valve. Vessel A contains 134L of air at 2,639.66 kPa, 87.38°C. Vessel B, of unknown volume, contains air at 69.36 kPa, 6.33°C. The valve is opened and, when the properties have been determined, it is found that Pm = 1,041.50 kPa, tm = 46.30°C. What is the volume of vessel B?
A rigid, insulated vessel is divided into two compartments connected by a valve. Initially, one compartment, occupying 1.0 ft, contains air at 50 lb/in?, 750°R, and the other, occupying 2.0 ft?, is evacuated. The valve is opened and the air is allowed to fill both volumes. Assume the air behaves as an ideal gas and that the final state is in equilibrium. Determine the final temperature of the air, in °R, and the amount of entropy produced, in Btu/°R.
Q1: 100 m² of air per minute at 30 C° DBT and 60% RH is cooled to 20 CDBT by passing through a cooling coil at a pressure of 1 bar. Find: 1- Capacity of cooling coil in tons of refrigeration. 2- RH and WBT of air after cooling
Water vapor undergoes the following processes: a. From a state at 200 kPa and 600 ° C it expands isothermally up to 100 kPa. B. Immediately isobarically compressed to 2 m3 / kg. C. From this last state it follows an isochoric process until reaching 600 ° C. Perform: a. Plotting the processes on the exact P-ν diagram. You must use the diagram P-ν
Question 21 A rigid tank whose volume is 0.5 m, initially containing ammonia at 20°C, 1.5 bar, is connected by a valve to a large supply line carrying ammonia at 12 bar, 200°C. The valve is opened only as long as required to fill the tank with additional ammonia, bringing the total mass of ammonia in the tank to 136.7 kg. Finally, the tank holds a two-phase liquid-vapor mixture at 20°C. Determine the heat transfer to the ammonia in the tank from the surroundings, in kJ, ignoring kinetic and potential energy effects. Qcv > = kJ
13. Calculate the heat transfer, in Btu/lbm, for the reversible process 1-3 shown in Fig. 2.11. SHOW-FREE BODY DIAGRAM 3 MPa 2 kgls uhine s00 AP. 100°C Fig. 2.11 Fig. 2.12
A balloon filled with 0.4 grams of helium, initially at 27°C, 1.3 bar, is released and rises in the atmosphere until the helium is at 17°C, 0.90 bar. Assume the helium behaves as an ideal gas. Determine the initial and final volumes, in cm³.
(25%) Q2. It includes wet vapor of R717 with a quality of 0.2 at a temperature of 15°C in a frictionless and well insulated piston-cylinder system shown in Fig. 2. Refrigerant is mixed with a propeller and initially occupies a volume of 5 L. When the pressure inside the cylinder reaches 800 kPa, the pin holding the cylinder will be broken and the propeller will stop, simultaneously. The piston moves upward after breaking the pin up to the point where equilibrium condition is obtained. Refrigerant is at saturated condition and a temperature of -15°C when the system reaches thermodynamic equilibrium. Calculate (a) the work done by the propeller, (b) The work done by the Fig. Q2 Piston- refrigerant after the pin is broken, and (c) the final volume of the refrigerant, (d) the entropy change of the refrigerant, (e) the entropy generation through this process. R717 cylinder system
A piston-cylinder assembly contains 3 kg of water at 120oC and 1.5 bar. The water is compressed to liquid-vapor mixture state where the pressure is 4 bar, quality 80%. During the compression, there is a heat transfer of energy from the water to its surroundings having a magnitude of 350kJ. Neglecting changes in kinetic energy and potential energy. Determine the specific internal energy at state 1 (u1), in kJ/kg Determine the specific internal energy at state 2(u2), in kJ/kg Determine the work for the process, in kJ, and judge the direction of energy flow by the work (into the system or from the system)
Two vessels A and B of different sizes are connected by a pipe with a valve. Vessel A contains 140 L of air at 3000kPa, 90oC. Vessel B, of unknown volume, contains air at 70 kPa, 5oC. The valve is opened and, when the propertieshave been determined, it is found that pm = 1400 kPa, tm = 45oC. (a) What is the mass in kg of air initially inside vessel A (b) What is the volume of vessel B in liters?
I need help with the steps of this practice problem. Can I get help to solve it ? A piston cylinder device contains 0.8 kg of air initially at 100 kPa, 27 °C. The air is now compressed slowly in a polytropic process during which PV1.3=constant, until the volume reaches 1/2 its original volume. The system is then heated at constant pressure until the volume gets back to its original value. NOTE: THIS IS NOT A CYCLE. Data: Rair = 0.287 kJ/kg K; Cv=0.731 kJ/kg K; Cp=1.018 kJ/kgK. a) DeterminetheamountsANDdirectionsoftheWorkandHeat(each in kJ) for each of the two processes. SHOW ALL WORK used to get your values. b) Sketch the two processes on a P-v diagram, clearly showing all three state points and the two processes with their directions.