A rod is subjected to a uni-axial load within linear elastic limit. When the change in the stress is 200 MPa, the change in the strain is 0.001. If the Poisson's ratio of the rod is 0.3, calculate the modulus of rigidity.
Q: 1. A steel rod 500mm long and 20mm× 10mm in cross-section is subjected to axial pull of 300 KN.If…
A:
Q: A plastic bar of 88 mm is to be twisted by torques T until the angle of rotation between the ends of…
A:
Q: A steel rod with a cross-sectional area of 0.20 in is stretched between two fixed points. The…
A:
Q: A load of 20 kN is applied to a rod with a diameter of 12.5 mm. Calculate the strain in the rod if…
A: Given Data: The load applied, P=20 kN Diameter of the rod, d=12.5 mm Young's modulus, E=103 GPa
Q: 2. An elastic rod of 25mm in diameter, 200mm long extends by 0.25mm under a tensile load of 40KN.…
A:
Q: A tensile stress is to be applied along the axis of a cylindrical brass rod that has a diameter of…
A: given; diameter (d)=10mmchange in diameter (δd)=2.5*10-3mmelasticity(E)=10.1*104MPapoisson's…
Q: . A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their…
A: Given Tensile modulus, E1 = 10 GPa E2 = 0.4 GPa Find Tensile…
Q: 6) A steel rod with a cross-sectional area of 0.25 in? is stretched between two fixed points. The…
A:
Q: Calculate the modulus of rigidity and bulk modulus of a cylindrical bar of diameter of 25 mm and of…
A: Relation between the lateral and the longitudinal strain is εl=4εd The poison's ratio is…
Q: Find the tensile stress in the rod having a diameter of 25 mm subjected to a tensile load of 500 N.…
A: Given, Diameter of rod = d = 25 mm Tensile load = P = 500 N Young's modulus = E = 200 GPa = 200 x…
Q: a. A metal thickness 16mm and having a rectangular cross-section carries a load of 60KN. Find the…
A:
Q: Calculate the modulus of elasticity of the following material if it has a design stress of 250 kPa,…
A:
Q: The longitudinal strain in a cylindrical bar of diameter 20mm and length 2.5m during the tensile…
A:
Q: Find the strain energy of a steel rod, of diameter 20 mm and length 400 mm, when it is subjected to…
A: Given:d=20 mmlength, l=400 mmP=40 KNE=200 GPa
Q: A steel rod of diameter 10 mm carries an axial load of 10 kN. Consider the modulus of elasticity and…
A:
Q: Calculate the strain (e) for a change in length (ō) and a length (L), where Ŏ = 0.015 in and L = 5…
A: Given data : Initial length L=5 ft Change in length δ=0.015 in Required : Strain
Q: A rod 150 cm long and diameter 2.0 cm is subjected to an axial pull of 20 kN. If modulus of…
A: As per given question Given data Rod length =150cm Diameters =2.0cm Axial pull =20 kn Modulus of…
Q: 3. If the engineering strain in a tensile bar is 0.0025 and Poisson's ratio is 0.33, find the…
A:
Q: Two bars of different materials and same size are subjected to the same tensile force. If the bars…
A:
Q: 4. A cylindrical metal wire 2m long is loaded in tension, causing it to extend 15mm. Calculate the…
A: GivenL=2m∆L=15mm=0.015m
Q: When the stress conditions are given as shown below, the materials are identical in all areas and…
A:
Q: A steel bar is stressed to 280 MPa. The modulus of elasticity is 205 GPa. The bar is 80 mm diameter…
A: Given data : Length (L)=240 mm Modulus of elasticity (E)=205 GPa Diameter (d)=80 mm Stress (σ)=280…
Q: A bar subjected to a stress of 1 GPa develops an elongation of 5mm. If the initial length of the bar…
A:
Q: Consider a cylindrical nickel wire 1.6 mm in diameter and 3.5 × 104 mm long. Calculate its…
A:
Q: Find the value of strain if initial length of rod is 100 m and change in length of rod due tensile…
A: Given data : Initial length of rod=L Change in length of rod=∆L Required : Strain
Q: Q.1 A 2 m solid steel bar of diameter 100 mm is subjected to a axial tensile load of 100 kN. Find…
A: Given: The diameter of the shaft is, d=100 mm. The length of the steel shaft is, l=2 m. The value…
Q: 04: A cross-sectioned rod (5*5cm) was subjected to a compressino force (F=500*10³ N), so the…
A:
Q: A rod 200 cm long and of diameter 3.0 cm is subjected to an axial pull of 30 kN. If the Young’s…
A:
Q: A tube has 25mm outside diameter and an axial tensile load of 40 kN. If the strain on the tube is…
A:
Q: Find the stress if strain 0.55 and modulus of elasticity is 50 MPa
A: Given data : Modulus of elasticity=E Strain=ε To find : Stress
Q: If the length and diameter of a material is 25 cm and 10 mm respectively. Then find the elongation…
A: Given : load, W =750*103N length, L=250mm diameter,d =10mm Area,A =π/4*d2 =78.53 mm2 young modulus ,…
Q: A rod is subjected to a uni-axial load within linear elastic limit. When the change in the stress is…
A: Given data: The change in the stress is σ = 200 MPa. The change in the stain is ε = 0.001. The…
Q: 3. A wrought iron rod is under a compressive load of 350 kN. If the permissible stress for the…
A: We are suppose to solve only one question. Please post other question as a separate question. For…
Q: A hollow cylinder 2 m long has an outside diameter of 50 mm and inside diameter of 30 mm. If the…
A: According to Hooke's Law, Stress is directly proportional to the strain up to a certain point. After…
Q: After a fall, a 98 kg rock climber finds himself dangling from the end of a rope that had been 17 m…
A: Given:-m=98 kgL=17 mD=9.8mm∆L=3.1cm=0.031mTo find:-a) Strainb) Stressc) Youngs modulus
Q: A hollow copper pipe undergoes a 1% change in length under a tensile load. If the Young’s modulus of…
A: We have been given the following data:The percentage change in length of the hollow copper pipe,…
Q: A rod is subjected to a uniaxial load within linear elastic limit. When the change in the stress is…
A: Given data: The change in stress, σ=200 MPa. The change in strain, ε=0.001. The Poisson's ratio,…
Q: A rod is subjected to an uni-axial load within linear elas limit.When the change in the stress…
A:
Q: A steel specimen is subjected to a tensile force of 400 kips. If the Poisson's Ratio is 0.20, and…
A:
Q: A wrought iron rod is under a compressive load of 350 kN. If the permissible stress for the material…
A: Compressive load on the rod, P=350 kN=350*103 N Permissible stress for the material, σ=52.5 N/mm2
Q: A tensile stress is to be applied along the long axis of a cylindrical brass and that has a diameter…
A:
Q: A metal bar 5.0 m long extends by 0.05 m when a load is applied to it. The strain is?
A: Given that, Length of the metal bar, L = 5 m, Change in length of the bar after applying load,…
Q: A rod is subjected to an uni-axial load within linear elastic limit.When the change in the stress…
A:
Q: If the engineering strain in a tensile bar is 0.0025 and Poisson’s ratio is 0.33, find the original…
A:
Q: Determine poisson ratio if lateral strain -0.01 and longitudinal strain is 0.02
A: Given data : The value of lateral strain=εT The value of longitudinal strain=εL To find :…
A rod is subjected to a uni-axial load within linear elastic limit. When the change in the stress is 200 MPa, the change in the strain is 0.001. If the Poisson's ratio of the rod is 0.3, calculate the modulus of rigidity.
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 1 images
- A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressureA brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
- A circular cylindrical steel tank (see figure) contains a volatile fuel under pressure, A strain gage at point A records the longitudinal strain in the tank and transmits this information to a control room. The ultimate shear stress in the wall of the tank is 98 MPa, and a factor of safety of 2,8 is required. (a) At what value of the strain should the operators take action to reduce the pressure in the tank? (Data for the steel are modulus of elasticity E = 210 GPa and Poisson's ratio v = 0.30.) (b) What is the associated strain in the radial directionA rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
- A rod is subjected to a uni-axial load within linear elastic limit. When the change in the stress is 200 MPa, the change in the strain is 0.001. If the Poisson's ratio of the rod is 0.3, the modulus of rigidity (in GPa) isA rod is subjected to a uniaxial load within linear elastic limit. When the change in the stress is 200 MPa, the change in the strain is 0.001. Calculate the modulus of rigidity if the poisson's ratio is 0.3.The longitudinal strain in a cylindrical bar of diameter 20mm and length 2.5m during the tensile stress is 3 times the lateral strain. Calculate the modulus of rigidity, bulk modulus and also find the change in volume when the bar is subjected to hydrostatic pressure of 150MPA. Take E = 150GPA.
- Find the tensile stress in the rod having a diameter of 25 mm subjected to a tensile load of 500 N. If Young's modulus of the material is 200 GPa, what is the strain in the rod?Find the value of strain if initial length of rod is 100 m and change in length of rod due tensile load is 0.0023 mA rod is subjected to a uniaxial load within linear elastic limit. When the change in the stress is 200 MpA. The change in strain is 0.001. if the poisson's ratio of the rod is 0.3, the modulus of rigidity will be,