A screw is rotated as shown to provide tension on a cable that passess over a frictionless pulley and pulls on themiddle block as shown. The weight of the blocks are W, = 120 lb, W, = 164 lb, W, = 146 lb and the coefficientof static friction for each surface is, µ, = 0.50, µ̟ = 0.43, µz = 0.23. If the bolt with square threads, has a radius, r= 0.32 in, a lead, L = 0.63 in, and a coefficient of friction of µ = 0.41 what is the torque necessary to cause one orboth blocks to move?%3Dw,FrictionlessPulleyW,w,HyTorqueDirection

The given figure is shown below:

A screw is rotated as shown to provide tension on a cable that passess over a frictionless pulley and pulls on the middle block as shown. The weight of the blocks are W, = 120 lb, W, = 164 lb, W, = 146 lb and the coefficient of static friction for each surface is, µ, = 0.50, µz = 0.43, µz = 0.23. If the bolt with square threads, has a radius, r = 0.32 in, a lead, L = 0.63 in, and a coefficient of friction of µ = 0.41 what is the torque necessary to cause one or both blocks to move? w, Frictionless Pulley w, w, Torque Direction

A screw is rotated as shown to provide tension on a cable that passess over a frictionless pulley and pulls on the middle block as shown. The weight of the blocks are W, = 120 lb, W, = 164 lb, W, = 146 lb and the coefficient of static friction for each surface is, µ, = 0.50, µz = 0.43, µz = 0.23. If the bolt with square threads, has a radius, r = 0.32 in, a lead, L = 0.63 in, and a coefficient of friction of µ = 0.41 what is the torque necessary to cause one or both blocks to move? w, Frictionless Pulley w, w, Torque Direction

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The forces and couples shown are applied to two screws as a piece of sheet metal is fastened to a…

A: (a) Write the force at point O in vector notation. FO=-15j N Write the force at point A in vector…

Q: Compute for the linear weight of 10 mm reinforcing bar. (Use the unit weight of the Steel). a 0.692…

A: Solution Given the dia of steel d= 10mm So the area will be A=π/4 * 10² 24=25π mm²

Q: 1000 N 1500 N/m A C D В 2 m 2 m

Q: A system of cables is shown and is in a state of equilibrium. Using equilibrium equation, solve for…

A: To find tension in cable AB

Q: The plate as shown weighing 25 kN is raised by a cable sling. The cable sling has the identical…

A: This question is related to the solid mechanics. In this question using Force equilibrium equations…

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the…

Q: 2. A line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long…

A: a.) Actual length of rope The expression for weight of the tape is given as W=wg Substitute the…

Q: Four forces are applied to the machine component ABDE as shown. Replace these forces with an…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

A: The given data is shown below: Diameter of aluminium rod=19mmElastic modulus=69 GPaDiameter of steel…

Q: A steel plate 2.5 m x 1.3 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the…

Q: 4.5m Bronze -3.5m Steel T 120 mm

Q: 1. A flexible connection consisting of rubber pads (thickness t= 9mm) bonded to steel plates is…

A: Hi there! since you have asked multiple questions, we will solve the first question for you. If you…

Q: 4. Determine the maximum load P that can be applied in the system consisting of a bent bar bolted at…

A: Given data: dB=1/4 in. dw=7/8 in. t=3/8 in.

Q: For the portal frame shown in the given figure, the shear equation is B 4 m C P-

A: the direction of the sway to the right if the frame sway due to the load acting at a joint then its…

Q: The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and…

Q: 3. Solve for the minimum tension on the cable necessary to open the circular gate AB. Neglect the…

Q: A SOLID ALUMINUM SHAFT 2 INCH DIAMETER IS SUBJECTED TO TWO TORQUES AS SHOWN IN THE FIGURE. DETERMINE…

Q: 3. The plate as shown weighing 25 kN is raised by a cable sling. The cable sling has the identical…

Q: A square plate 2 m on each side is supported by four steel tie rods 6-mm-diameter from an overhead…

Q: THE COEFFICIENT OF STATIC FRICTION BETWEEN THE BLOCK AND THE PLANE IS µs = 0.2. DETERMINE THE…

Q: D (1) h B a b

Q: The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and…

A: For the given rigid bar,

Q: Two identical metal sheets are formed into tubes with circular and square cross sections shown. If…

Q: Each member of the frame shown in Figure weighs 67 Ib per ft. Compute the horizontal component of…

Q: AP 35° 35°

Q: A 600 kg material is hung from the end of the horizontal bar BD as shown. Determine the stress on…

Q: brass shaft has an equilateral triangle cross section. Determine the angle of twist at end C in…

A: As per guideline provided by the company, I have to answer only first question in cases of multiple…

Q: The four rigid gears, loaded as shown in the figure, are attached to a 2.98-in.-diameter steel…

Q: The plate as shown weighing 25 kN is raised by a cable sling. The cable sling has the identical…

Q: The compound shaft consists of bronze and steel segments, both having 125-mm diameters. If the…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

Q: 14. The plate shown in the figure is fastened to the fixed member by seven 10-mm-diameter rivets.…

A: We have to determine the value of load P so that average shear stress in any rivet does not exceed…

Q: The butt joint shown in the figure is connected using five 20 mm diameter bolt. If the tension force…

A: Shear forces acting in parallel with the solid body cause the conversion. As the liquid evaporates,…

Q: The allowable shear stress is 10ksi in the shaft shown. Determine the minimum required outside…

Q: Determine the selfweight W of the bar, the vertical movement of the bar at A and C and indicate the…

A: To find self weight of bar and deflection at point A and C

Q: G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods.…

Q: Cut a cross-section through the beam and draw a free body diagram to the left of the cut. Determine…

Q: 2 - A frame structure carries a sign, as shown in the figure below. The sign is made of steel (with…

Q: 228 kN B 2.5 m А 4.0 m 4.0 m Shown in the figure above is a truss (E = 300GPA) with 228kN loading.…

Q: Chain members (1) and (2) are connected by a shackle and pin. If the axial force in the chains is P…

A: An axial force is the compression or tension force acting in a member. If the axial force acts…

Q: 4. Determine the maximum load P that can be applied in the system consisting of a bent bar bolted at…

Q: 3) The rigid horizontal bar AB is supported by three vertical rods as shown in the figure and…

Q: As shown on the figure is a bar supported by two cables. If the bar has a mass of FN kilograms and…

Q: 03. Given the figure below, determinc the tension in the three cords (in KN) if the initial pull of…

Q: a 30m weighing 0.900kg has a cross-sectional area 0.0485cm^2. the tape measures 30.000m when…

A: given data : weight of tape (w)=0.9 kgModulus of elasticity (E)=2.1×106 kg/cm2Measured length…

Q: G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods.…

Q: The standard pull of the tape is 5kg while the team pulled only at 4kg The field temperature is 300…

Q: Determine the tension in the rope using Newton's 2nd Law. Hint: it is NOT 20 lb. WA = 20 Ib W = 20…

A: Given:- The weight of the block A = wA = 20 lb The weight of the block B = wB = 20 lb Coefficient of…

Q: Problem 1. A compound beam shown in the figure is fixed at point A, connection at B sa pin and C is…

Q: (a) Determine the deflection of the beam at point D by both Virtual Work Method and Castigliano's…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

A screw is rotated as shown to provide tension on a cable that passess over a frictionless pulley and pulls on the
middle block as shown. The weight of the blocks are W, = 120 lb, W, = 164 lb, W, = 146 lb and the coefficient
of static friction for each surface is, µ, = 0.50, µ̟ = 0.43, µz = 0.23. If the bolt with square threads, has a radius, r
= 0.32 in, a lead, L = 0.63 in, and a coefficient of friction of µ = 0.41 what is the torque necessary to cause one or
both blocks to move?
%3D
w,
Frictionless
Pulley
W,
w,
Hy
Torque
Direction

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The five-bolt connection must support an applied load of P = 149 kips. If the average shear stress in the bolts must be limited to 50 ksi, what is the minimum bolt diameter that may be used for this connection? P Answer: d = i in.
A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The connection consists of three 5/8-in. bolts that join two 1/4-in. end plates welded to the brace and a 5/8-in. gusset plate welded to the column. The compressive load P carried by the brace equals 8.0 k. Determine the following quantities: (a) The average shear stress (τ)ave in the bolts, and (b) the average bearing stress (σ)b between the gusset plate and the bolts. (Disregard friction between the plates.)
A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The connection consists of three 3/8-in. bolts that join two 1/4-in. end plates welded to the brace and a 3/8-in. gusset plate welded to the column. The compressive load P carried by the brace equals 6.0 kips. Determine the following quantities: (a) The average shear stress (τ)ave in the bolts, and (b) the average bearing stress (σ)b between the gusset plate and the bolts. (Disregard friction between the plates.)
For the clevis connection shown, determine the shear stress in the 23-mm-diameter bolt for an applied load of P = 165 kN. O 141 MPa O 211 MPa O 167 MPa O 120 MPa O 199 MPa Clevis
A bracket connection shown in figure, consists of a joist cutting welded to the flange of a column by shop fillet welds 8 mm on flanges and 6 mm on the web. Determine the safe service load 'W', the bracket can support at a distance of 200 mm from the face of the column if the steel grade is Fe 410. 200 200 8V 150 200 W 8 V 150 N 150 200 250 Partial factor of safety on shop weld = 1.25 Yield strength of steel = 250 MPa. 250 A
Part A If the required clamping force at the board A is to be 85 N, determine the torque M that must be applied to the handle of the "C" clamp to tighten it down. The single square-threaded screw has a mean radius of 10 mm, a lead of 3 mm, and the coefficient of static friction is u, = 0.35. Express your answer to three significant figures and include the appropriate units. M = 1.1142 Nm O The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Submit Previous Answers Request Answer Figure 1 of 1 Provide Feedback Next > M O Pearson
The lap joint shown is fastened by 6 – 20mm diameter rivets. Assuming that P = 200KN, determine (a) the shearing stress in each rivet, (b) the bearing stress in each plate 25mm thick and 100mm wide. Assume that
The lap joint of a tension member is shown. The plate is 252 mm wide and 12 mm thick. The bolts are 20 mm in diameter and the holes are 3 mm larger than the bolt diameter. Use A36 steel. a. Determine the safe value of P based on tension net area. Ft = 0.5fy b. Determine the safe value of P based on tension bearing failure. c. Determine the safe value of P based on tension block shear. Fv = 0.3fy, Ft = 0.5 fy
For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is 140 MPa. Assume the plates are adequate to transmit the load to the rivets. P= 60 KN. a) Determine the shearing stress in the most stressed rivet. b) Determine the maximum allowable value of P. c) If P=80 KN, determine the minimum diameter of rivets. USE NSCP 2015. Thanks.
Two bolts are used to lap points two steel plates. Tensile force on the plate is 45kN. Determine the required diameter of the bolts if the failure shear stress of the bolts is 350 MPa. Use a factor of safety for shear equal to 2.0
A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.
The bolted connection is subjected to a tensile force of P. The diameter of the bolt is d=60 mm. if P=200kPa. Determine the average shear stress (MPa) in the bolt.