A shaft/hub connection transmits a torque C =60N.m. We use a rectangular key (W=14mm x H=9mm) with a length of 30mm for a 45mm diameter shaft. Calculate the force exerted on the key.Calculate the compressive and shear stress.

A shaft/hub connection transmits a torque C =60N.m. We use a rectangular key (W=14mm x H=9mm) with a length of 30mm for a 45mm diameter shaft. Calculate the force exerted on the key.Calculate the compressive and shear stress.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.10P: Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the...

See similar textbooks

Related questions

Q: An L = 1-m-long vertical copper tube of inner diameter D, = 20 mm and wall thickness t = 2 mm…

A: Given-Information:- L = 1 m Di = 21 mm = 0.021 mt = 2 mm = 0.002 mTw = 0°C = 273 K V = 3m/sT∞ =…

Q: 4. Determine magnitude and location of forces on all vertical walls. Water 10 ft 15

Q: A 70 lb force P is applied to the brake pedal of a tractor, as shown below. Force Q is applied to…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

Q: A beam with a solid homogeneous rectangular section is simply supported at A and B. A concentrated…

A: To Find : The maximum bending stress. Given : The concentric load is F=275 kN The lenght A to C is…

Q: 1. Examine the following atmospheric altitude versus temperature data: Altitude (m) Temperature (°C)…

A: a) In order to determine the depth of mixing for pollution with a temperature of 28°C that is…

Q: QUESTION 4 A roller with the weight FG = 900 N is supported on two flat surfaces (see the picture)…

Q: Tc (2) (1) C B L₂ L₁ A

Q: Determine the magnitude of the gripping forces produced when two 50 lb forces are applied as shown.

Q: Since the force on the wheel is F = 3.4 kN, as in the figure, calculate the joint force FA and the…

A: Given Data

Q: In a steady spatially varied flow in a prismatic open channel, the (a) depth does not change along…

A: Given data:- a steady spatially varied flow in a prismatic open channel To find: choose the correct…

Q: 2. Forces T1, T2, and T3 are acting on the eye bolt. If the magnitudes of T1, T2, and T3 are 330 N,…

A: Given Data

Q: Draw a perspective,isometric(with 30 angle), & oblique(with 45 amgle) view of a cube.

A: Draw a perspective,isometric(with 30° angle), & oblique(with 45° angle) view of a cube.

Q: Grandpa/Shutterstock.com 7.3-26 An element in plane stress on the surface of an automobile drive…

A: σx=-45 MPaσy=? MPaτxy=39 MPaσ1=41 MPa

Q: 2. Calculate the room temperature saturation current and the forward current at 0.3V for a…

A: Room Temperature T=300K Active area A = 10-8m2 Constant C = 1019 A/m2K2 The work function is taken…

Q: (a) refrigerating effect, (b) circulating rate of refrigerant, (c) theoretical power, (d) COP, (e)…

A: As per Expert Guidelines, We are supposed to answer only the first three questions of the given…

Q: A system of 8-kg block A and 42-kg plate B is released from rest in the position shown. The motor…

A: mA=8 kgmB=42 kgFM=150t Nt= 5 sμAB=0.2μBC=0.1

Q: Which bearing designation refers to a deep groove ball bearing that is classified as extremely light…

A: Note: As per Bartleby Answering guidelines, we are supposed to give answer for first three…

Q: A particle moves in a horizontal line according to s=t^4 - 6t^3 + 12 t² - 10t + 3. Find the time…

A: Given data:- S= t4 - 6t3 + 12 t² - 10t + 3. To find:- The time when the particle is at rest The…

Q: The wedge is used to level the member. The coefficient of static friction between the wedge and the…

A: To determine: P = ?

Q: Look at the flow chart showing the steps of the design process. Then read the list of steps for…

Q: The strain rosette shown below was used to obtain normal strain data at a point on the free surface…

Q: An ammonia ice plant operates between a condenser temperature of 35°C and evaporator of -15°C. It…

A: Given data is

Q: When a uniform stream flows past an immersed thick cylinder, a broad low-velocity wake is created…

A: Given: To find: Drag force

Q: In order to experimentally determine the moment of inertia Ig of a 4-kg connecting rod, the rod is…

Q: Determine the second moment of area (lxx) about the centroidal x-axis for the solid homogeneous beam…

A: Given data:- b=12.75 mm d=32.39 mm To find:- The second moment of area about centroidal x-axis (Ixx)

Q: What does the red arrow in this figure represent? TA 14 3 O a. Compressor O b. Intercooling O c.…

A: To Choose : The appropriate option . Given : The T-s diagram is,

Q: 1. Measuring the pressure of a pipeline transferring heavy oil The manometer connected to the line…

Q: The 2000 kg car is being lowered using a hoist and a winch. Determine the forces in cable BC in 2.2…

A: Given data is

Q: The assembly shown consists of a flywheel, a counterweight, and a bolt that attaches the…

Q: A small barge is being used to transport trucks across a river. If the barge is 10.00 m long by 8.00…

A: Given data:- The barge length =10.00 m width of the barge =8.00 m depth of sinking = 3.70 cm To…

Q: A steel column of 19-ft effective length must carry a centric load of 338 kips. Using Allowable…

A: The length of column, L = 19 ft The allowable load, P = 338 kips The depth of column, h = 12 in The…

Q: Write the kinematic equations for rectilinear motion for variable acceleration.

A: This question is based on the equation of rectilinear motion

Q: A 1-m-wide rectangular gate is hinged about a horizontal axis along its lower edge Determine the…

Q: An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air…

A: The ideal Otto cycle compression ration is given as 8 The initial pressure of the compression…

Q: In the mechanism in the figure, the movement of the pin A in the circular slot is controlled by the…

Q: A hollow bronze shaft with an outside diameter of 80 mm and a wall thickness of 5 mm is subjected to…

A: D=80mmt=5mmT=620 Nm=620×103 NmmP=9500 N

Q: A 55 kW refrigeration load is to be carried by an air refrigeration system with a discharge pressure…

Q: 2) The compression ratio of an ideal Otto cycle is 7 and prior to compression air is at 285K and…

A: “Since you have posted a question with multiple sub parts, we willprovide the solution only to the…

Q: Average speed is defined as

A: This question is based on the concept of average speed.

Q: 11Fluid power energy primarily directed and controlled by A) Cylinders B) Electricity C) Pumps D)…

A: 11] Fluid power energy is primarily directed and controlled by pumps and valves. Pumps are used to…

Q: The 575-N force is applied to the 98-kg block, which is stationary before the force is applied.…

Q: 26. Basic dynamic load rating is the load that a bearing can be subjected to while achieveing…

A: 26)According to the standards of bearing design, Basic dynamic load rating is the load at which a…

Q: A 55 kW refrigeration load is to be carried by an air refrigeration system with a discharge pressure…

A: Refrigeration load (R.E.)= 55 kW P2 = 1370 kPa Refrigerator pressure P1 = 345 kPa. n=1.37 The…

Q: Which statement is fals? O In an isolated system of many particles in equilibrium a microstate with…

A: This question is based on the concept of thermodynamics.

Q: mass d is listed as 10 however you made it zero for equillibrium i think thats wrong but i might be…

A: Given Data

Q: A rigid container contains 10 kgs of air at 100 kPa and 22°C. A 1-kW heater is placed in the…

A: Given data:- A rigid container mass of air =10 kg Pressure =100 kPa Temperature =22 °C =295 K…

Q: Designers may employ solid modelling to give their works a three-dimensional, organic feel rather…

A: Solid modeling is a technique used by designers in computer-aided design (CAD) to create…

Q: C = R= 01 = 60 160 Determine the principal stresses 01 and 2 for the stress element shown above: 02…

Q: 4.30 The horizontal force P is applied to the handle of the puller. Determine the resulting tension…

A: Given: Force P is applied to the handle To determine the tension T in the Chain

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculations for the force and compressive stress on the key

VIEW

Step 3: Calculation for the shear stress on the key

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A keyed sprocket delivers a torque of 778.8 N-m thru the shaft of 54 mm OD. The key thickness is 1.578 cm and the width is 1.11 cm. Compute the length of the same key. The permissible stress value of 60 MPa for shear and 90 MPa for tension. (Ans: 4.33 cm)
Design a square key for a 3 in diameter shaft to withstand a torque of 30000lb-in. The design stresses in shear and bearing can be safely taken as 11 ksi and 22 ksi, respectively. Find the length (inches) From Table AT 19, b=t=3/4 in
A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has the following standard dimensions: b x h x l = 8 mm x 7 mm x 18 mm. Calculate the stresses.
What length of a square key is required for a 5-in diameter shaft transmitting 1000 hp at 1000 rpm? The allowable shear and compressive stresses in the key are 15 ksi and 30 ksi, respectively.
A 16 in. diameter motor pulley is running at 600 rpm with a 6 in diameter shaft transmitting power to an agricultural locomotive. If the dimensions of the square key is 0.5 x 3 in, what is the maximum force in the pulley’s belt that can be transmitted if the shear stress is limited to 8500 psi and bearing stress limited to 4000 psi?
Design a rigid flange coupling to transmit a torque of 250N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Answer in Word please
Two 400 mm diameter pulley are keyed to a simply supported shaft 500mm apart. Each pulley is 100 mm from its support and has horizontal belts, tension ratio being 2.5. If the shear stress is to be limited to 80MPa while transmitting 45 kW at 900 rpm. Find the shaft if it is to be used for the input - output belts being on the same or opposite sides.
The figure below is a schematic drawing of a shaft that supports two V-belt pulleys. The loose belt tension on the pulley at A is 15% of the tension on the tight side. The shaft material has a yield strength of 300 MPa and an ultimate tensile strength of 520 MPa. Calculate the shaft diameter.
The diameter of shaft is 45mm. Compare the shear stress in the key to the torque in the shaft. calculate the key size to use for the 15 kW low speed shaft with a speed of 384 rpm. Take bxb = 10mm x 10mm as d = 45mm L = 1.5 cm.