A shunt machine has armature and field resistances of 0.04 2 and 100 2 respectively.When connected to a 460 V d.c. supply and driven as a generator at 600 r/min, it delivers50 kW. Calculate:i.The generated e.m.f.ii.The speed of the machine in r.p.m., when running as a motor and taking50 kW from the same supply.CS Scanned with CamScanner

Answered: Image /qna-images/answer/0f0717f3-9e9e-4100-b539-1f4f08d75871.jpg

Answered: A shunt machine has armature and field…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

) A d.c. shunt machine while running as generator develops a voltage of 240 V at 1000 rp.m. on no-load It has armature resistance of 0.52 and field resistance of 250 92. When the machine runs as motor, input to it at no-load ts 4 A at 240 V. Calculate the speed and efficiency of the machine when it runs as a motor taking 40 A at 240 V. Armature reaction weakens the field by 6%
• A DC shunt machine while running as generator develops a voltage of 250 V at 1000 r.p.m. on no-load. It has armature resistance of 0.5 ohm and field resistance of 250 ohm. When the machine runs as motor, input to it at no-load is 4 A at 250 V. Calculate the speed and efficiency of the machine when it runs as a motor taking 40 A at 250 V. Armature reaction weakens the field by 4 %
The armature of a d.c. The machine has a resistance of 0.25 ohm and is connected to a 300V supply. Determine the e.m.f. generated when it runs as a generator giving 100 A and as a motor taking 80 A. please check the back emf calculations
The resistance of the field winding(copper wire) of a DC machine is 0.25 ohm at 25°C. When operating at full-load, the temperature of the winding is 75 °C. The temperature coefficient of resistance of copper is 0.00427 per °C at 0°C. Find the resistance of the field winding at full-load.
A DC shunt generator delivers 45 A at a terminal voltage of 220 V. The armature and the shunt field resistances are 0.01 2 and 44N respectively. The stray losses are 375 W. What is percentage efficiency of the DC generator
A shunt generator supply 100A at 200 V. The armature and shunt resistance are 0.025 and 100 ohms respectively. If the copper losses are equal to the iron losses at this load. Find the HP of engine driving the generator. (Our subject is ELECTRICAL MACHINE 1, and our lesson is Losses and Efficiency on the DC MACHINE)
b) A newly built institution has bought a D.C. shunt generator to supply a library in order for students to study using electrical power from this machine when there is load shedding on the national grid. The total load of the library is 50 kW through the cables of total resistance of 0.04. The winding resistance of the generator is 5092 and the armature resistance is 0.072832. The library is to be supplied at 0.4kV. i. Draw the circuit diagram indicating all the above stated values. ii. Determine the load current (IL). iii.Determine the terminal voltage of the generator. iv. Determine the armature current. v.Determine the E.M.F. generated in the armature.
4) A dc. ahunt machine while running as generator develops a voltage of 240 V at 1000 rpm. on no-load It has armature resistance of 0.5 12 and field resistance of 250 2. When the machine runs as motor, input to it at no-load ts 4 A at 240 V. Calculate the speed and efficiency of the machine when it runs as a motor taking 40 A at 240 V. Armature reaction weakens the field by 6%
A 220 V dc machine has an armature resistance of 1ohm if the full load current is 20 A, the difference of induced voltage, when the machine is running as a motor and generator, is *
Q- The armature resistance of a permanent magnet dc motor is 0.80. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be
Problem # 1: A four-pole DC machine has a wave winding of 300 turns. The flux per pole is 0.025 Wb. The DC machine rotates at 1000 rpm. a) Determine the machine constant, b) Determine the generated voltage, c) Determine the kW rating if the rated current through the turn is 25 A. Problem # 2: The following information is taken from the nameplate of a separately-excited dc generator. Armature: 120 kW, 600 V, 0.15 Q. Field: 100 V, 6.0 A At its rated speed of 3600 rpm the no-load torque is measured at 16 Nm. Ignore armature reaction and magnetic saturation. a) For rated load conditions determine: i) Rated Shaft Horsepower ii) Rated Efficiency iii) Load Impedance b) Determine the terminal voltage, kW output and the efficiency if the field current is reduced to 4.5 A, and the speed is reduced to 3000 rpm, causing the rotational losses to become 4 kW. The load impedance is unchanged.
A 220 V DC machine has an armature resistance of 1 Q. If the full load current is 20 A, what is the difference in induced voltage when the machine is running as generator and motor under full load condition

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS