A single phase bridge inverter has an RLC load with R= 20 ohms, L = 32 mH and C = 0.115 mF. The inverter frequency is fo= 60 Hz and DC input voltage is Vs = 110 V. The RMS magnitude of the 1st harmonic of the output current is equal to: Select one: a. 4.34A b. 6.42A OC. 0.955A Od. None of these

A single phase bridge inverter has an RLC load with R= 20 ohms, L = 32 mH and C = 0.115 mF. The inverter frequency is fo= 60 Hz and DC input voltage is Vs = 110 V. The RMS magnitude of the 1st harmonic of the output current is equal to: Select one: a. 4.34A b. 6.42A OC. 0.955A Od. None of these

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: For the op-amp shown in the following figure, the midrange voltage gain is equal to- 3 kn w 80 kn…

A: Given circuit diagram is,

Q: D₁ # R₁ www D₂ R3 R₂ Reverse Biased D1 Forward Biased Reverse Biased D2 lo Forward Biased 0.7V…

A: Given: A circuit, with, R1=R2=R3=5 k?, V1=5 V, V2=15 V, and the diodes IV characteristics are…

Q: How you can get "1" at the output of the following logic circuit? OUT All of the above A=1 B=0 C=0…

Q: USEFUL FORMULAS Properties of valid Autocorrelation function (ACF) The ACF of a signal is defined as…

Q: V_ds=? drain-source =?

A: The required potential difference between drain and source terminal need to be calculated and the…

Q: Find the voltage across the capacitor as a function of time for t> 0 for the given circuit. Assume…

A: Given: with the assumption that the circuit is in steady state for t<0 and Vi = 55 V. To find:…

Q: 4.46 The electric field intensity in free space is given by E = 2 xyz ax + x²z ay + x²y a₂ V/m…

A: Electric field intensity in free space is, E=2xyzax+x2zay+x2yaz V/m Charge Q=2 C is required to move…

Q: find the transfer function

A: Given: A network, To find: Transfer function,

Q: Self inductance of an inductor with toroidal geometry is 231 nH. The total number of turns of this…

A: It is given that: L=231 mHN=16I=17 A

Q: 5. A three-phase rectification system has a voltage ripple of 14%. If the output kVp is 150, what is…

A: In this question we need to find the minimum voltage

Q: Compute the output of a system if the input and impulse response are given as x[n] = (-0.5)¹u[n - 4]…

Q: Express the following function as a single sinusoid and hence find their amplitude and phase f(t) =…

A: Given Function: f(t)=2Cos(2t) + 3Sin(2t) To determine: Express function as a single sinusoid, its…

Q: a) A given PM signal is: PM (t) = 10 cos [90×10° πt+200 cos 2000 t] Determine the carrier frequency…

Q: In a certain magnetic circuit, the core is represented two reluctances as shown below. Assume a…

A: The magnetic circuit diagram is shown below, Number of turns, N=640 turns.Current, I=2.2 A.

Q: 1. In a certain region, the electric field is given by D = 2p(z+1) cos(p)app(z+1)sin(p)a+p²cos(p)az…

Q: VOLO Amps 4.2 +j652 2.52 ig (t) = 10 cosine 377 t 2g Amps.

Q: what is the minimum voltage? a) 129 kvp b) 14 kVp c) 86 kVp d) 21 kVp e) 10.7 kVp ge ripple

A: Given data, Output voltage VO=150 V. Ripple voltage Vr=14 %.

Q: 11. A three-phase 420-kV, 60-HZ transmission line is 463 km long and may be assumed lossless. The…

A: Sending end voltage (VS) = 420 kV (line) Receiving end voltage (VR) = 700 kV (line) no load So, at…

Q: Assume piecewise linear function with one segment one is used, and the cost function of each of…

A: According to the question, we need to find the slope of piecewise linear function as shown below,…

Q: A transformer has a primary voltage of 240 V and a secondary voltage of 48 V. What is the turns…

A: Turn ratio of transformer

Q: Thank you that helped a lot but In which part of the drawn circuit are inputs??

A: Given sequence is an irregular counter sequence . In the given sequential circuit for the given…

Q: 3. Use your method of choice on the circuit below to find the average power associated with all…

Q: SHOW YOUR COMPLETE SOLUTION. MAKE SURE YOUR FINALS ANSWER ARE IN 4 DECIMAL PLACES. A 750-kVA,…

Q: (iv) Explain why there is a short period between pulses when the output voltage is zero. (v)…

Q: Calculate the percentage voltage drop for a transformer with a percentage resistance of 2.5% and a…

A: p.u. resistance=2.5%, p.u. reactance=5% Rating=500 KVA, 400 KVA @ 0.8 p.f. lagging, To Find- The…

Q: Perform the following items. Show your solution. 1. Determine the frequency of oscillation of a…

Q: Bonus) Z-75-100 f=1.09 GHz C1 C L1 L=? R1 R=500 Find the values of C1 and L1 that cause the…

A: Given data R1=50 Ω Z=75+j0 Ω f=1.09 GHz To find out We have to determine the value of L1 and C1.

Q: The low voltage side of a particular transformer has 747 turns while its high voltage side has 69471…

A: Transformer primary turns (N1)=747 Transformer secondary turns (N2)=69471 secondary impedance is…

Q: For the op-amp filter circuit shown above, assume C₁ = 10nF, R₁ = 1k, and Rf = 5kN. Find the…

Q: Describe the working principle of loop/sense antenna in ADF. Then, draw the resulting radiation…

A: It is asked to describe the working principle of loop/sense antenna in ADF. Also we need to draw the…

Q: Question 2. Analogue Systems (a) Find the frequency response (magnitude and phase) of a system whose…

Q: The magnetic structure of a synchronous machine is shown schematically in Figurel. Assuming that…

A: For the magnetic structure of a synchronous machine,μ→∞.I=10A.N=1000 turns.g=1mm.Ag=2000 cm2.

Q: The question I am having trouble with is: Design a 3 bit sequential circuit using D flip flops and…

A: We need to design a 3-bit sequential circuit using D-flipflops and one input 'X'. If X =0 => no…

Q: The op amp in the circuit shown in Fig. Problem is ideal. Calculate the reactive power delivered by…

Q: Compute the Fourier transform of the following signal - Σk=0 ak 8(t – kT), |a| < 1

Q: 1.- Find the phase relations for V = = 6 sin(30t - 40°), i = 10 sin(30t – π π/3) V₁ = -8 sin(40t -…

Q: A three-phase line has its conductors at the corners of an equilateral triangle of side 1 m. The…

A: A three-phase line- Conductors at the corners of the equilateral triangle, Side of triangle a = 1 m,…

Q: Representing a transmission line by the two-port network, in terms of ABCD parameters, express Vs,…

A: The sending end voltage in the form of receiving end parameters.

Q: 2. Convert the block diagram into a signal flow and find the transfer function of C₂/ R₁. R₁ R₂ H₁…

A: In this question we need to convert the given block diagram in signal flow graph ( SFG ) and with…

Q: What is the phase angle between voltage and current in a series cuircuit consisting of an…

A: In this question, We need to determine the phase angle between voltage and current in series RL…

Q: What will be the value of the Unknown inductance Lx (in mH) and the effective resistance Rx (in 2)…

Q: Problem# 3. Determine v, in the circuit below anyway you like: Draw the frequency-domain network and…

A: The provided answer is not clearly visible. Hence I am providing the correct answer. Please follow…

Q: Draw five automatic control circuits for three phase motors ?

A: We have to Draw five automatic control circuit for three phase motors

Q: SINE(0 6Vp-p 1.5K) R₁ LL 2.5 mH 100 PL On the load, find the Power (P) in Watts (W) R A 180//180 Ω…

A: Given Data: A series RL circuit with, Peak-to-peak voltage Vpp=6 V Frequency f=1.5 kHz To Find:…

Q: ) Given an input voltage from power supply battery, V dc-12V, f=3 kHz and ON time is 0.2m Calculate…

A: Given : Vdc=12 Vf=3 kHzTON=0.2 ms

Q: The op amp in the circuit shown has a slew rate of 3V/usec. Calculate the rise time Tsr due to the…

A: According to the question, for the given non inverting amplifier as shown below The op amp in the…

Q: Example 1 Amplitude of carrier signal is given 10 V, and free 20MUC This carrier is modulated by 16…

A: Given: Carrier signal has, amplitude Ac=10 V and frequency fc=20 MHz. Carrier signal is modulated…

Q: Shield wires located above the phase conductors protect the phase conductors against lightning. a.…

A: The given statement is related to the use of shield wires in protecting the phase conductors against…

Q: Draw a schematic from a PCB obtained from the instructor or use the above picture of the PCB. The…

A: The given PCB layout needs to be converted into a schematic diagram based on the connections in the…

Q: Solve for the current in this circuit. Give its phase angle and write it as a phasor. V1 20 V 1 kHz…

A: In this question we need to find the phase angle and the current I in phasor domain

Question

A single phase bridge inverter has an RLC load with R= 20 ohms. L = 32 mH and C = 0.115 mF. The inverter frequency is
fo= 60 Hz and DC input voltage is Vs = 110 V. The RMS magnitude of the 1st harmonic of the output current is equal to:
Select one:
a. 4.34A
b. 6.42A
OC. 0.955A
Qd. None of these

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Explanation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The load voltage waveform of a single phase full bridge inverter supplied from 30OV DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load vahues are 22 and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 008 .01 .012 .014 .016 .018 .02 Time (sec) a. Calculate and draw the load current for the first two-period interval b. Calculate and draw the load current for the steady-state condition c. Find the RMS values of the load voltage and the load current d Calculate and draw the voltage across the load inductance e. Calculate and draw the source current and find its average vahue
QUESTION SEVEN A single-phase bridge inverter is fed from 230 V dc. In the output voltage wave, only fundamental component of voltage is considered. Determine the rms current ratings of an SCR and the diode of the bridge for the following types of loads: (a) R = 20 (b) wL = 29. Find also the repetitive peak voltage that may appear across a thyristor in parts (a) and (b).
The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load values are 2N and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 .008 .014 ,02 .01 Time (sec) .012 .016 .018 a. Find the RMS values of the load voltage and the load current b. Calculate and draw the voltage across the load inductance c. Calculate and draw the source current and find its average value
2) A single-phase full-bridge inverter has a DC voltage source V = 230 V. The rms value of the fundamental component of the output voltage is a- 90 V. b- 207 V. C- 350 V. d- 196 V.
A single phase half bridge inverter is operating from a 25 V DC source and supplies power to resistive load. What is the distortion factor of fundamental output voltage?
An inductive load is supplied from a single-phase inverter that uses a thyristor and diode. The supply voltage is 100 V. Draw the circuit of the inverter and describe with the help of equation and waveforms, how it can be used to generate AC voltage. Also derive the equation of RMS load voltage.
A single phase bridge inverter has an RLC load with R-20 ohm, L32 mit and C-0115 m The inverter frequency is to 60 H and DC input voltage is Vs 110V The average current of each transistor is equal to fontider up to the fifth harmonics in calculation Select on O None of these b 18A Oc 223A Od 6.JA
Electrical Engineering HGJGJGJGJGJJGJGJG 2. A single-phase half-bridge inverter is connected to a 600V d.c. source. A series connected R-L load has R = 60 ohm, L = 70mH. The inverter frequency is 60Hz. Determine the values of the rms load current, the load power and the total harmonic distortion factor, up to the 11th harmonic. 41 a₁0₁ D₂ ia₁ 12 h R₁ 44 Q₂ in V₁ la D₂ D₁ **PLS SOLVE QUESTION CORRECTLY, THANK YOU. L₁ www
With a single phase full bridge square wave inverter connected to a 24V DC power supply, 50H output frequency AC output is aimed. The load resistance is 10 ohms and the inductor is 250mH. Calculate the maximum value (in milliamps) of the load current. a) 546 b) 474 c) -546 d) -474 e) 323
A single phase half bridge inverter has input voltage of 48 V DC. Inverter is feeding a load of 2.4 ohm. The rms output voltage at fundamental frequency is ?
One half bridge inverter with bidirectional switches and one full bridge inverter with bidirectional switches are connected to similar loads (R=102) and providing both an output power of 1 KW. The rms transistor currents of the half bridge and full bridge inverters are respectively: Select one: O a. 5A, 7.07A O b. 5A, 5A O c. 7.07A, 5A Od. None of these
Show that the THD of the phase voltage of the three-phase inverter square-wave mode is 0.31