A single phase half a bridge bipolar PWM inverter is operated from a center top 240 volts DC supply. The fundamental output frequency is adjusted to 50 Hz, the carrier frequency used is 1.2 kHz, modulation index is adjusted to 0.8. Determine: i) Carrier ratio (Mf) and the number of pulses per cycle. ii) fundamental output voltage. iii) distortion and harmonic factor of the output voltage waveform. vi) Draw the waveforms created O a. 24 O b. 16 O c. 20 O d. 12

A single phase half a bridge bipolar PWM inverter is operated from a center top 240 volts DC supply. The fundamental output frequency is adjusted to 50 Hz, the carrier frequency used is 1.2 kHz, modulation index is adjusted to 0.8. Determine: i) Carrier ratio (Mf) and the number of pulses per cycle. ii) fundamental output voltage. iii) distortion and harmonic factor of the output voltage waveform. vi) Draw the waveforms created O a. 24 O b. 16 O c. 20 O d. 12

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single phase half bridge inverter has input voltage of 48 V DC. Inverter is feeding a load of 2.4 ohm. The rms output voltage at fundamental frequency is ?
A single phase inverter has square wave output voltage. What is the percentage of the fifth harmonic component in relation to the fundamental component ?
6-If the collector resistance is shorted,the ac output voltage will a-Decrease. b-Increase. c-Remain the same. 9 d-Equal zero. 7-If input impedance of the second stage decreases, the voltage gain of the first stage will a-Decrease. b-Increase. c-Remain the same. d-Equal zero. 8-If the load resistance of second stage opens, the voltage gain of the first stage will a-Decrease. b-Increase. c-Remain the same. d-Equal zero. 9-The feedback resistor a-Increases voltage gain. b-Reduces distortion. c-Increases collector resistance. d-Decreases input impedance. 10-when the emitter resistance Rp doubles the ac emitter resistance a-Increases. b-decreases. c-Remains the same. d-Cannot be determined. 11-To reduce the distortion in a CE amplifier, reduce the a-DC emitter current. b-Base-emitter voltage. c-Collector current. d-AC base voltage. 12-The output voltage of a CE amplifier is a-Amplified. b-Inverted. c-180° out of phase with the input. d-All of the above.
FETs have similar properties to ___. a. Scotty diodes b. NPN transistors c. PNP transistors d. uni-junction transistors
What is the difference between dc-dc switching mode regulators and PWM Inverters ?
iv. For six-phase half-wave rectifier circuit, the preferred circuit from the point of harmonics reduction in the supply currents is: (a) Simple six-phase half-wave circuit. (b)Double-star six-phase half-wave circuit. (c) Six-phase fork connection circuit. v. The DC supply of single phase bridge inverter is 350V. For quasi-square wave output voltage with a 70 percent ON time and frequency is 50HZ, the RMS value of output voltage is: (a) 292.8V (b) 220.5V (c) 250.6V
2. a) Compare and differentiate a single phase full bridge inverter with a single phase full bridge rectifier in terms of construction and operation. Discuss how the switching operation of the inverter can effect the output waveform and total. harmonics distortion (THD) value.. Use suitable diagram for better explanation.
draw the three output voltage (Vab, Vbc, Vca) wave shapes of a three phase inverter. Draw the switching diagram and mode circuits for each mode. The conduction angle is 150 degree. What will be the rms value of the output voltage?
Solve this: Transistor AC Analysis a. Determine the re b. Calculate the Vb and Vc c. Determine the Zi, Zout, and Av
Explain the process of Transistor’s Engineering.
Question 1 A single phase half bridge inverter feeds a resistive load R= 5N. If the source voltage is 60V. determine the (a) magnitude of output voltage (b) RMS value of fundamental component of output voltage (c) output power (d) voltage across the switches and (e) RMS and average value of current through the switch.
Sketch the dc load line. Show detailed graph/sketch and computation of values plotted.