A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be replaced by a soild circular bar. a. Determine the required diameter of bar so that the maximum shear stress in the bar will not exceed the maximum shear stress in the tube. b. If the computed value of diameter in the previous question increase by 15%, what is the new shear stress of the circular bar? c. Determine the angle of twist in degrees of the tube if the length of the tube is 1m and the shear modulus is 80 GPa. Use T=14 kN-m.

A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be replaced by a soild circular bar. a. Determine the required diameter of bar so that the maximum shear stress in the bar will not exceed the maximum shear stress in the tube. b. If the computed value of diameter in the previous question increase by 15%, what is the new shear stress of the circular bar? c. Determine the angle of twist in degrees of the tube if the length of the tube is 1m and the shear modulus is 80 GPa. Use T=14 kN-m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An aluminum tube with the cross section shown has a constant wall thickness of 2 mm. A torque T = 400 N·m is applied to the tube. Use G= 28 GPa What is the area of the tube? a. 957.08mm2 b. 968.09mm2 c. 966.08mm2 d. 977.08mm2 What is the total length of the median line? a. 0.1313m b. 0.1314m c. 0.1315m d. 0.1316m What will be the result shear flow of the object? a. 207,967.94 N/m b. 208,968.98 N/m c. 209,978.96 N/m d. 209,979.00 N/m The shearing stress value will be? a. 104.5 MPa b. 105.6 MPa c. 104.6 MPa d. 105.7 MPa The angle of twist result is? a. 14.68 Deg/m b. 12.66 Deg/m c. 14.68 Deg/m d. None of the above.
Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 55 MPa in the shafts and 23 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
Required information Link AB, of width b = 2 in. and thickness t= in., is used to support the end of a horizontal beam. The average normal stress in the link is -21 ksi and the average shearing stress in each of the two pins is 12 ksi. 4 NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the diameter d of the pins. The diameter d of the pins is in.
The vertical load P acting on the wheel of a traveling crane is 13,000 lb. What is the average shear stress in the 1.25 in. diameter axle?
The rectangular piece of wood, 51 mm by 183 mm, is used as a compression block. The grain of the wood makes a 31.6° angle with the horizontal, as shown in the figure. Determine the largest axial force P (in N) that can be applied safely if the allowable stresses on the plane of the grain is 11.9 MPa for compression. Round off the final answer to three decimal places. 018 shear.png ...
The 1.5-in diameter solid steel shaft is simply supported at the ends. Two Pulleys are keyed to the shaft where pulley B is of diameter of 4 in and pulley C is of diameter of 8 in. Transverse shear stress needs to be considered. 2) At cross section B, determine the normal stress at points E, F, and G, and the shear stress at point E and F. (cross section B is on the right side of pulley B, and G is the midpoint of EF). y 10 in 200 lbf 1000 lbf B 10 in 500 lbf 100 lbf 10 in Z F G E y
The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m2. What will be the stress along the face AB? (Cambridge) ANSWER: 17.68 kN; 11.8 MN/m2 compressive.
A 1.25 in.-square steel punch is to push through an aluminum plate that is supported on a die, thus forming a square opening in the plate. a. If the allowable compressive stress in the plate is 24 ksi, what is the maximum punching force, in pounds, that this die can exert on the plate? b. If the aluminum has an ultimate shear strength of 6500 psi, find the maximum thickness t, in inches, through which a hole may be punched. Write to three decimal places. Punch force Steel punch Aluminum plate Die Punched piece
Link AB, of width b = 2 in. and thickness t = 1414 in., is used to support the end of a horizontal beam. The average normal stress in the link is -18 ksi and the average shearing stress in each of the two pins is 12 ksi. Determine the average bearing stress (ksi). **The way I had solved it was that I used the given normal stress to first find the P force needed to plus into my bearing stress formula. I still however need the diameter. The answer key says to use the given shear stress equation to find the diamter, how do you know to use that and not the shear stress formula again?
The constant wall thickness of a tube with the elliptical cross section shown is 0.12 in. What torque will cause a shear stress of 6000 psi?
The maximum torsional shear stress of a shaft with diameter D can be found at what distance from the center of the shaft?
If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d = 100 mm with 3 mm thick walls is T = 12 kNm, which of the following is closest to %3D the magnitude of the minimum shear stress developed on that section? Select one: O A. 262 MPa O B. 501 MPa O C. 279 MPa O D. 533 MPa