A steam pipe 50 mm diameter and 2.5 m long has been placed horizontally and exposed to still air at 25 degree Celsius. If the pipe wall temperature is 295 degree Celsius, determine the rate of heat loss. At the mean temperature difference of 160 degree Celsius, the thermo-physical properties of air are k =3.64 * 10 -2 W/m v =30.09 * 10 -6 m2/ P r =0.68 Β =1/160 + 273 = 2.31 * 10^-3/K

A steam pipe 50 mm diameter and 2.5 m long has been placed horizontally and exposed to still air at 25 degree Celsius. If the pipe wall temperature is 295 degree Celsius, determine the rate of heat loss. At the mean temperature difference of 160 degree Celsius, the thermo-physical properties of air are k =3.64 * 10 -2 W/m v =30.09 * 10 -6 m2/ P r =0.68 Β =1/160 + 273 = 2.31 * 10^-3/K

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.17P: Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID,...

See similar textbooks

Similar questions

Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55
A steam is flowing through a 5.7 m long of steel tube that has inner and outer radii of r, = 0.015 and r, 0,024 m, and a thermal conductivity of 0.14 W/m.K. The steam and the outer surface of the tube is maintained at constant temperature of 150 °C and the air = 25 °C, h = 0.35 W/m2.k) is surrounding the tube. To prevent the outer surface of the steel from the environmental conditions, a material that has a thermal conductivity of 0.014 W/m.k is wrapped over the outer surface of the steel. What is the maximum heat transfer from the steam to the air (W)? NOTE: Enter your answer. Answer Air Th Steam Steel Tr 111 To
A thermometric well is placed in a pipe having diameter of 55 mm. Pipe wall temperature is 100°C and heat transfer coefficient inside the pipe is 300 W/m² K. Thickness of thermowell is 1.2 mm and its length is 50 mm. Thermal conductivity of thermowell material. Is 30 W/mK. If the temperature of the gas flowing through the pipe is recorded by thermometer as 200°C, determine the true temperature of gas. If the error in gas temperature is to be reduced by 80% by increasing the length of thermowell, determine the new length of thermowell. Draw a sketch of this thermowell. Take perimeter to area ratio for thermowell as 1/T (T= thickness).
Quiz: A double-pane window consists of two 3 mm thick layers of glass separated by a 12 mm wide stagnant air space. For specified indoors and outdoors temperatures. 1. Determined rate of heat loss through the window and 2. The inner surface temperature of the window. kalass = 0.78 W/m-°C and k stagnant space = 0.026, The area of the window and the individual resistances are A=(1.2 m)x (2 m) = 2.4 m² Glass Glass Stagnant space Toi= 24 h = 10 w/m?.c To2- -5 c h2 25 w/m2.c 12 mm 3 mm mm
Determine conductive resistance (in K/W) of a 80 m^2 plane wall composed of 2 layers: Layer 1: brick, thickness δ1 = 620 mm, thermal conductivity λ1 = 0.310 W/(m.K) Layer 2: EPS, thickness δ2 = 52 mm, thermal conductivity λ2 = 0.026 W/(m.K) Evaluate the heat loss through this wall if indoor temperature is 22 C and outdoor temperature is -18 C.
Saved Help Save & Exit A 2-kW resistance heater wire with thermal conductivity of k= 70 W/m-K, a diameter of D= 4 mm, and a length of L = 0.9 m is used to boil water. If the outer surface temperature of the resistance wire is Ts= 230°C, determine the temperature at the center of the wire. (Round your answer to a single decimal place.) 230 C -D→ es Resistance heater The temperature at the center of the wire is °C 18°C Clear ^ 4 ENG
An oil radiator has an outside surface area of 0.18 m2 and operates at a surface temperature of 85 degree Celsius. If air moves over the surface of the radiator at a temperature of 16 degree Celsius and gives rise to a heat transfer coefficient equal to 38.25 W/(m2-K). Find out the heat transfer flux? O 2923 W/m2 O 3801 W/m² O 2639 W/m² O 1659 W/m²
Convection 2. For a boiling process such as shown in Figure below, the ambient temperature Tin Newton's law of cooling is replaced by the saturation temperature of the fluid Tsat. Consider a situation where the heat flux from the hot plate is q=20 x 105 W/m². If the fluid is water at atmospheric pressure and the convection heat transfer coefficient is hw=20 x 103 W/m2 K, determine the upper surface temperature of the plate, Ts, w. In an effort to minimize the surface temperature, a technician proposes replacing the water with a dielectric fluid whose saturation temperature is Teat, d=52 °C. If the heat transfer coefficient associated with the dielectric fluid is h = 3 x 103 W/m2 K, will the technician's plan work?
1. Saturated steam at 500 K flows in a 0.20 m inside diameter, 0.21 m outside diameter pipe. The pipe is covered with 0.075 m of insulation with a thermal conductivity of 0.10 W/m-K. The pipe's conductivity is 52 W/m-K. The ambient temperature is 300 K. The unit convective coefficients are hi = 18,000 W/m²-K and ho 12 W/m²-K. Determine the heat loss (kJ/min) from 5 m of pipe.
One vessel having a carbon-steel wall of thickness 5 mm carrying saturated steam and water at 423K. The vessel is insulated with magnesia of thickness 50 mm. If the ambient air temperature is 321 K, determine the heat loss from the vessel. Given: i. thermal conductivity of carbon steel is 52 W/m.K ii. thermal conductivity of magnesia is 0.5 W/m.K iii. surface coefficient of insulation surface is 3 W/m2.K
A 0.1 m diameter long rod at 20 °C is to be heated by a hot fluid of 200 °C. How long does it take the rod temperature to reach 70% of the fluid temperature if the followings are given? Convection coefficient h = 10 W/m2K Thermal conductivity k = 20 W/mK Thermal diffusivity a = 10-5 m2/s
Question 6 1 pts A composite wall constructed of 2.5cm of steel (k-60.5 W/m-K) and 5.0 cm of aluminum (k177W/m-K) separates two liquids. The liquid on the steel side has a film coefficient of 15W/m²-K and a temperature of 400degC. The liquid on the steel side has a film coefficient of 30W/m² and a temperature of 100degC. Assume steady state conditions, what is the temperature at the steel-aluminum interface in deg C