A tensile test uses a test specimen that has a gage length of 50 mm and an area = 200 mm². During the test the specimen yields under a load of 98,000 N. The corresponding gage length = 50.23 mm. This is the 0.2 percent yield point. The maximum load = 168,000 N is reached at a gage length = 64.2 mm. Determine: (a) yield strength Y, (b) modulus of elasticity E, and (c) tensile strength TS.

A tensile test uses a test specimen that has a gage length of 50 mm and an area = 200 mm². During the test the specimen yields under a load of 98,000 N. The corresponding gage length = 50.23 mm. This is the 0.2 percent yield point. The maximum load = 168,000 N is reached at a gage length = 64.2 mm. Determine: (a) yield strength Y, (b) modulus of elasticity E, and (c) tensile strength TS.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tensile test specimen has a gage length = 3.0 in and diameter 0.75 in. Yielding occurs at a load of 38,000 lb. The corresponding gage length = 3.0103 in (neglect the 0.2 percent yield point). The maximum load of 54,000 lb is reached at a gage length = 3.453 in. Determine the modulus of elasticity (neglect the 0.2% offset, and round to the nearest whole Msi). 37
tensile test uses a circular test specimen that has a gage length of 50 mm and diameter = 20 mm. During the test the specimen yields under a load of 100,000 N. The corresponding gage length = 50.5 mm. This is the 0.2% yield point. The maximum load of 180,000 N is reached at a gage length = 65 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength. (d) If fracture occurs at a gage length of 73 mm, determine the ductility. i need clear ans by hand and solve very very fast in 20 min and thank you | DYBALA
A tensile test specimen has a gage length = 3.0 in and diameter 0.75 in. Yielding occurs at a load of 38,000 lb. The corresponding gage length 3.01 03 in (neglect the 0.2 percent yield point). The maximum load of 54,000 lb is reached at a gage length 3.453 in. Determine the tensile strength (round to the nearest whole Ksi) 38
37) A tensile test specimen has a gage length =3.0 inches and a diameter=0.75 inches. Yielding occurs at a load of 38000 lbs. The corresponding gage length 3.0103 inches (neglect the .2% yield point). The maximum load of 54000lb is reached at gage length 3.453 inches. Determine the modulus of elasticity. (Neglect the .2% offset and round to the nearest whole Msi)
A tensile test specimen has a gage length = 3.0 in and diameter 0.75 in. Yielding occurs at a load of 38,000 lb. The corresponding gage length 3.01 03 in (neglect the 0.2 percent yield point). The maximum load of 54,000 lb is reached at a gage length 3.453 in. Determine the yield strength (round to the nearest whole Ksi). 36
Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain = 0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in the y-direction, the width strain was measured to be gw=-0.1000 at that instant. The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi. Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be expected.
A tensile test specimen has a gage length = 50 mm and its cross-sectional area = 100 mm?. The specimen yields at 48,000 N, and the corresponding gage length = 50.23 mm. This is the 0.2 percent yield point. The maximum load of 87,000 N is reached at a gage length = 64.2 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength. %3D
A tensile test was performed on a metal specimen with a diameter of 1/2 inch and a gage length (the length over which the elongation is meas- ured) of 4 inches. The data were plotted on a load-displacement graph, P vs. AL. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/AL = 1392 kips/in. What is the modulus of elasticity? BI
Problem 2: A specimen of steel having an initial diameter of 0.503 in was tested in tension using a gauge length of 2 inches. The following data were obtained for the tension. Plot the stress strain data and determine the modulus of elasticity, and the yield strength of the material. Elastic State Load P Ibf Elongation in 1 000 0.0004 2 000 0.0006 3 000 0.0010 4 000 0.0013 7 000 0.0023 8 400 0.0028 8 800 0.0036 9 200 0.0089
Problem No. 2 The above load-elongation data were obtained for a specimen with Lo = 0.1 m and ro 7 mm. Plot the stress-strain data and determine the E, G, and of Load (KN) 0.0 12.8 36.7 43.5 47.0 50.1 61.4 71.6 74.2 71.6 67.6 Elongation (mm) 0 0.0201 0.0690 0.1173 0.1898 0.2864 1.1684 3.5052 7.3025 10.2235 13.7287
A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 10^6 psi. When the same specimen is used in a tensile test, the modulus of elasticity is found to be 12.2 x 10^6 psi. Find Poisson's ratio for the specimen. * 0.95 0.30 0.40 0.33
lin. = 0.2 x 103 in. You test a concrete cylinder having a diameter of 6.00 in and a gauge length of 12 in by applying compression forces. The results of your test are reported in the table as load vs. contraction. Draw, by hand on engineering paper, a stress-strain diagram using scales of: 1 in. = 0.5 ksi in. From the diagram, determine approximately the Modulus of Elasticity. Load (kip) Contraction (in) 0.0 0.0000 5.0 0.0006 9.5 0.0012 16.5 0.0020 20.5 0.0026 25.5 0.0034 30.0 0.0040 34.5 0.0045 38.5 0.0050 46.5 0.0062 50.0 0.0070 53.0 0.0075