A three-terminal manual starting rheostat has a resistance of 5.2 ohms in its starting resistor. The holding coil resistance is 10 ohms. This starting rheostat is connected to a shunt motor. The resistance of the armature is 0.22 ohm; the resistance of the shunt field is 100 ohms. The line voltage is 220VDC. a. What is the starting surge current taken by the motor? b. What is the current in the holding coil with the moveablew arm in the run position? c. What is the CEMF with the movable arm in the on position if the armature current is 20 amps?

A three-terminal manual starting rheostat has a resistance of 5.2 ohms in its starting resistor. The holding coil resistance is 10 ohms. This starting rheostat is connected to a shunt motor. The resistance of the armature is 0.22 ohm; the resistance of the shunt field is 100 ohms. The line voltage is 220VDC. a. What is the starting surge current taken by the motor? b. What is the current in the holding coil with the moveablew arm in the run position? c. What is the CEMF with the movable arm in the on position if the armature current is 20 amps?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

What are the options suits for a slip ring induction motor? (A) Slip ring induction motor has high starting torque (B) Slip ring Induction motor has a complicated construction (C) Slip ring induction motor has high efficciency (D) Slip ring induction motor has more copper loss O a. (A) and (B) O b. (A), (B) and (C) O c. (A) and (C) O d. (A), (B) and (D)
A freewheeling DC motor is driven with 1000 rpm and a nominal load torque of 80Nm. The field circuit resistance is 200 and the armature circuit resistance is 0.2 O. The field coils are fed with a zero degree transmission angle through a single-phase fully controlled converter connected to a single-phase 240V source. The armature circuit is fed from a single phase 400V source through another fully controlled converter. Magnetic saturation has been neglected, the motor constant is given as 0.8 V - s / A - rad. Assuming that there is no fluctuation in armature and field current, find the control angle of the converter feeding the armature at nominal load. If you want to leave the question blank, click again on the option you marked.
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights. design the single-phase, full-wave, ac/ dc converter. show design specifications, the reason for DC motor selection. correct manual circuit, and correct automatic closed-loop control circuit
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights.
A DC chopper is used in regenerative breaking mode of a dc series motor. The dc supply is 600 V, the duty cycle is 70%. The average value of armature current is 100 A. It is continous and ripple free. What is the value of power feedback to the supply ?
A 48kW, 600V, 1500 rpm separately excited dc motor is controlled by single phase semi-controlled converter. The resistance of the armature is 192 and of the field is 1450. The field circuit is controlled by a single phase fully controlled converter and its firing angle is set to 20. The AC supply voltage to the armature and field converters is a single phase 220V, 60 Hz. The voltage constant is 0.946 V/A rad/s. If the armature converter firing angle is 45 and the speed is 1200 rpm; calculate the armature current and the developed torque.
An 8 pole, 50 Hz slip ring induction motor runs at a slip of 2.67% on full load. The rotor resistance per phase of the winding is 0.2 ohm. What external resistance per phase must be added in the rotor circuit so that the motor now runs ate a slip of 17.33% such that the torque remains same in both the cases. (Ans: 1.1 ohm)
6- In a stepper motor, how is the speed of rotation determined? a) By the current supplied to the motor. b) By the magnitude of the voltage applied. c) By the load applied to the motor. d) By the frequency of the waveforms used. 7- A transformer core is laminated to a) reduce hysteresis loss b) reduce eddy current losses c) reduce copper losses d) reduce all above losses 8- An induction motor with 580 r.p.m. speed at 60 Hz will have a) 8 poles b) 6 poles c) 4 poles d) 2 poles 9- If any two phases for an induction motor are interchanged a) the motor will run in reverse direction b) the motor will run at reduced speed c) the motor will not run d) the motor will burn 10- No-Load speed of which of the following motor will be highest? a) Shunt motor b) Series motor c) Short-Shunt compound motor d) Long-Shunt compound motor
Speed control of a 140 V, 1.68 kW DC motor single phase thyristor full wave AC-DC It is made by the converter. AA supply voltage 220 V (rms) Is 50. In the converter It is assumed that there is no loss. The armature resistance of the DC motor is = 0.417 Q. Very a large inductance is connected in series with the motor. The motor voltage constant is = 0.0964 V/rpm. The motor can be considered as a permanent magnet DC. According to this, a) Draw the driver (converter-motor) power circuit. b) Calculate the nominal current of the motor. c) Supply voltage, supply current, converter output voltage for ignition angle a = 30 ° and Draw the waveforms for the converter output current. d) = 950 rpm and for nominal current, d1) The firing angle of the converter, d2) Effective value of supply and thyristor current, d3) Supply power factor, calculate.
1. Single phase full converter is used to control the speed of separately excited DC motors. AC supply voltage is 208 V. Motor armature and field resistance are 0.5 2 and 345 2 respectively. The field current is also controlled by a full converter and the field current is set as the maximum possible value. Motor voltage constant is 0.7 V/A-rad/sec. If firing angle is 45° and armature current is 55 A, determine the angular speed of the motor. Assume armature and field current are ripple free.
c) What is the physical meaning for each of the following induction motor parameters: R1 „R2 ,Rc ,X1 ,X2 ,Xm ?
Name three factors that determine the torque produced by an induction motor.