A three-phase Δ-connected generator has an internal impedance of 9+j90 m Ω/ϕ. When the load is removed from the generator, the magnitude of the terminal voltage is 13,800 V. The generator feeds a Δconnected load through a transmission line with an impedance of 20+j180 m Ω/ϕ. The per-phase impedance of the load is 7.056+j3.417 Ω. Construct a single-phase equivalent circuit.

A three-phase Δ-connected generator has an internal impedance of 9+j90 m Ω/ϕ. When the load is removed from the generator, the magnitude of the terminal voltage is 13,800 V. The generator feeds a Δconnected load through a transmission line with an impedance of 20+j180 m Ω/ϕ. The per-phase impedance of the load is 7.056+j3.417 Ω. Construct a single-phase equivalent circuit.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14MCQ: The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load...

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
The total instantaneous power delivered by a three-phase generator under balanced operating conditions is (a) A function of time (b) A constant
H* 3G zain IQ Asiacell The generator convert from PV to PQ if the active power of the generator exceed the * maxinum and minimum limits between the maximum and mimium limit equal to the load power Non of them With base voltage of 450 kV. The actual voltage of the generator is 560 kV. The magnitude voltage in the parameter of the PV generator in the nepaln software is * O 1.2444 pu O 450 kV O 124.44 % O 0.8036 pu 80.36 % Non of them
2. A voltage applied to a load is V=208420°V and current through load is I=10 &-10° A. Find the following [SO 1] o complex power consumed by load • Is the load inductive or capacitive? o the power factor of the load o the reactive power consumed or generated by the load. o Does the load consume or supply reactive power? 3. A single phase motor draws 20 kVA at 0.70 lagging power factor from a 120 V source. The PUD desires to improve the power factor to 0.9 lagging by connecting a shunt capacitor bank across the terminals of the motor. Determine the size of the capacitor bank in VARS. Calculate the following: [SO 1] a) What are the initial load current, real and reactive powers of the load? b) What are the real and reactive power after adding the capacitor bank? c) What is the kVAr rating of the capacitor bank? (3) d) What is the load current? di) How is the load current affected by the load reactive power?
There is an installation with two identical three-phase motors, 50 HP each and a power factor of 0.9 behind. When connecting a pure reactive element in parallel, the reactive power at the installation input is 50 kVARS, with a lagging power factor. We can say that: a) A capacitor bank was connected and the pf improved. b) A bank of inductors was connected and the pf improved. c) A capacitor bank was connected and the pf deteriorated. d) A bank of inductors was connected and the pf deteriorated. e) None of the above.
Three Impedances each of (9 - j18)N are connected in mesh across a three-phase 415V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip) Line current real power reactive power
Zjine 1:10 10:1 VG = 13.84 0° kV Zoad T1 T2 A 13.8-kV, single-phase generator supplies power to a load through a step-up transformer, a transmisson line, and a step-down transformer as in the figure above. Assume the transformers are ideal. The load's impedance is Zload = 200 L 36.87°, and the transmission line's impedance is Zline = 80 L 60° What is the efficiency of the transmission system?
1. What is the main direct cause of reactive power in AC system? A. Resistance of transmission lines B. Inductance and capacitance in the loads C. Ideal transformer connected in the system D. Power produced by generator 2. "Reactive power in a system is dissipated generally as thermal energy?" A. TRUE B. FALSE 3. Which of the following statements are correct for three phase circuit: A. Sum of all the three phase currents is zero in unbalanced network B. Total power transfer to load is constant with time C. Neutral conductor is same size in terms of material used as in single phase conductors D. Net apparent power consumed is equal to real power
Zjine 1:10 10:1 VG = 13.84 0° kV Z1oad T1 T2 A 13.8-kV, single-phase generator supplies power to a load through a step-up transformer, a transmisson line, and a step-down transformer as in the figure above. Assume the transformers are ideal. The load's impedance is Zload = 200 L 36.87°, and the transmission line's impedance is Zine = 70 L 60° What are the transmision losses in Watts?
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
a. Y-Connected b. В 100kW Source 0.9 LAG 80KVA 0.8 LAG Figure 1 80kW 0.85 LAG