HW2A vertical concrete pipe of length L = 1.0 m, outside diameter dout = 15 cm, insidediameter din = 10 cm is compressed by an axial force F = 1.2 kN as shown inFigure 4.5. Assuming the modulus of elasticity of concrete to be E = 25 GPa andPoisson's ratio as v = 0.18, determine:(a) the shortening in the pipe length(b) the lateral strain «y(c) The increase in the outer and inner diameters Ddout and Ddin(d) The increase in the pipe wall thickness Dt(e) The percentage change in the volume of the tube (DV / V) 100.1.2 KN1.0 m15 cm10 cm

Note- Since we only answer up to 3 sub-parts, we’ll answer the first3. Please resubmit the question…

Answered: A vertical concrete pipe of length L =…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following data of a pre-stress concrete are given: Beam dimension ; bxh = 300 mm x 600 mm Loads Super imposed dead load 7 KN/m Live load = 20 KN/m Unit Weight of concrete 23 KN/cubic meter The beam is simply supported on a span of 15 meters and are pre tensioned with total initialpre tensioned with total initial force of 1750 KN from low-relaxation strand with centroid 220 mm below neutral axis throughout the beam length .There is a 15% loss of stress at service loads. The concrete covering of the pre-stressed concrete is _____mm., the total dead load is _____ KN/m.
Assuming concrete is uncracked. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 1x10°kg cm . Determine the cracking moment of the section. A = 10cm² %3D E, = 2*10°kg / cm² E = 2*10°kg / cm² %3D %3D f'. =1836kg / cm² %3D 90 cm 100 cm 40 cm
Item 5 Column AB is made from high strength pre-cast concrete and reinforced with four in diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow) con = 2.6 ksi and (allow) st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 x 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 1 ▾of 1 10 ft a P B9 in. 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. μA Pmax= 158.91 kips Submit My Answers Give Up Incorrect; Try Again; 2 attempts remaining ? Provide Feedback Continue
Concrete re in orced a enially with eight steel column bars as shown in Fig. Each bar has diametes of 25 mm It opplied load 4 KN, compute the is 180 Gpa and 3. materi al. Es Stress developed in Ec = 12 Gpa. each 500mm %3D 500mm in
Consider a rectangular column subjected to axial compression. The material stress-strainrelationships have been idealized as shown below.a) What axial load will cause concrete to be at its maximum working stress?b) find the axial load P which produces εc = εs = 0.0011 NOTE : ( X1=124.6 , X2=385 , X3= 178 ) PLEASE HELPPP
A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 26.27 MPa and fy = 414 MPa. Calculate the nominal capacity based on the maximum steel area for a tension- controlled condition. Use the following dimensions: b = 498 mm d = 709 mm t = 152 mm web thickness - 152 mm b 1 I d
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
3-1. A concrete cylinder having a diameter of 6.00 in. and gage length of 12 in. is tested in compression. The results of the test are reported in the table as load versus contraction. Draw the stress-strain diagram using scales of 1 in. = 0.05 ksi and 1 in. = 0.2(10-)in./in. From the diagram, determine approximately the modulus of elasticity. Load (kip) 0 5.0 9.5 16.5 20.5 25.5 30.0 34.5 38.5 46.5 50.0 53.0 Contraction (in.) 0 0.0006 0.0012 0.0020 0.0026 0.0034 0.0040 0.0045 0.0050 0.0062 0.0070 0,0075
The cross section of a beam is shown in the figure is reinforced with 5-28 mm diameter bars placed at 100 mm from the bottom fiber. The beam is expected to carry a service moment of 280 kN-m. Use f'c=28 MPA and fy=280 MPa. All dimensions are in millimeters. Using WSD method, calculate the following: 1. Cracking moment of the section. 2 Compressive stress on the concrete., 3. Tensile stress on the steel. 4. Compressive force on the concrete. 300 I00 300 300 300 100 mm 100 -1700 mm
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars, Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MP.. 640 mm 800 mm 6 #32 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
A Normal-weight concrete T beam shown in the figure below is reinforced at the tension side by 3 - #25 bars. The concrete is assumingly uncracked and has a compressive strength of fe' = 29 MPa, fy=370 MPa, and the clear concrete cover is 40 mm, the modular ratio is n=9, and the web rein. is #10 mm. Determine the cracking moment (kN m) of the section using solution 2. 1300 125 250 500
Design a one way slab (as shown in fig) for inside of a building. Normal weight aggregate concrete will be used with a density of 145pcf. Compressive strength of concrete = 4000psi Yield strength of steel = 60000psi LL = 250psf

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS