A W12x65 wide flange beam supports the distributed load and concentrated force shown. Determine: 1. The maximum flexural tension stress in the beam 2. The maximum transverse shear stress in the beam 3. The state of stress at a point x = 4 ft and 3 inches down from the top of the beam For all three parts, summarize the result on a 2D stress block.

A W12x65 wide flange beam supports the distributed load and concentrated force shown. Determine: 1. The maximum flexural tension stress in the beam 2. The maximum transverse shear stress in the beam 3. The state of stress at a point x = 4 ft and 3 inches down from the top of the beam For all three parts, summarize the result on a 2D stress block.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The curved bar shown has a cross section of 30 x 30 mm. Knowing that the allowable compressive stress is 175 MPa, determine the largest allowable distance a. Take P= 4.5 kN. В. A. P P 30 mm 20 mm 20 mm 30 mm The largest allowable distance a is mm.
A beam has a uniform concentrated load (Pu) at midspan and has a fixed support at both end. If the beam properties are given below, what is the stress at bottom of the beam section at 2.76 from the support. (MPa)
Two vertical forces, each of magnitude P= 8 kN, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 10 mm 10 mm 50 mm- 50 mm 10 mm The maximum tensile stress is The maximum compressive stress is T B 150 mm MPa. 250 mm MPa. C 150 mm
Determine the shear stress at points: A, B. C, D and E in beam shown in Figure 5. Take E-30 GPa
Hi, The maximum stress can't be more than 10MPa so that cannot be the right answer. Also where do the figures for 69.5knm bending moment come from?
The internal shear force V at a certain section of an aluminum beam is 10.6 kN. If the beam has the cross section shown (assume a=39 mm, by 72 mm, tw-t-5 mm, d-84 mm), determine: (a) the shear stress rat point H, which is located 39 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress max in the tee shape. H Answers: (a) T₁ = (b) Tmas V MPa. MPa.
PROBLEM 4.9 25 mm Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 25 inm 4 kN 4 kN A 300 mm 300 mm
For the beam and loading shown, consider the n-n cross section. (a) the absolute value of |M| of the bending moment in the n-n section N.m (b) determine the absolute value of the normal stress in the direction of the X axis at point A of the n-n section |σx| MPa in units, c) determine the absolute value of the maximum shear stress at Point A of the n-n section |tmaks| MPa in units. The inside of the beam is full and the cross-section measures are as shown in the figure. Supports only support vertical forces. Take P1 in the question for 220 N and P2 for 323 N. Point A is at the bottom of the beam.
(A) he figure below shows three metal cubes A, B, C of side 100 mm in direct contact, resting on a rigid base and confined in x-coordinate direction between two rigid end plate. If the upper face of the center cube B is subjected to uniform compressive stress of 0.5 kN/mm², compute for cube B, the following: (i) The direct stress in x-direction (₂) (ii) The direct strains in the three coordinates directions x, y and z (iii) The volumetric strain Rigid A E=150 kN/mm² μ = 0.25 o₂ = 0.5 kN/mm² B E = 200 kN/mm² μ = 0.3 -Rigid C E = 150 kN/mm² μ = 0.25 Rigid
Consider the following figure. hị h A B (a) Determine the maximum tensile stress o, and maximum compressive stress o, (in MPa) due to the load P acting on the simple beam AB. Data are P = 6.8 kN, L = 3.4 m, d = 1.03 m, b = 80 mm, t = 25 mm, h = 120 mm, and h, = 90 mm. (Use the deformation sign convention.) MPa 0. = MPа (b) Find the value of d (in m) for which tensile and compressive stresses are the largest. What are these stresses (in MPa)? (Use the deformation sign convention.) = p MPa MPa
Problem 3: Member AC is subjected to a vertical force of 3 kN. Cross sectional area of tie rod is 400 mm? and the contact area at C is 650 mm?. O Determine the force in the tie rod if the average compressive stress at C is equal to the average tensile stress in the tie rod AB. ® Determine the compressive force at C. Determine the position x of the 3 kN force from A. 3 kN 200 mm
The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.