A weight weighing 15 Newtons starts on A, on top of a smoothing rolling mechanism with a velocity of 5 m/s. After passing through the mechanism, the crate will travel a distance d on a rough surface to B until it stops. The coefficient of kinetic friction is 0.4 N. Determine the distance d assuming a constant horizontal force of 21N (due to air resistance) is acting on the weight from the bottom of the mechanism to point B. 5 m/s 1 m

A weight weighing 15 Newtons starts on A, on top of a smoothing rolling mechanism with a velocity of 5 m/s. After passing through the mechanism, the crate will travel a distance d on a rough surface to B until it stops. The coefficient of kinetic friction is 0.4 N. Determine the distance d assuming a constant horizontal force of 21N (due to air resistance) is acting on the weight from the bottom of the mechanism to point B. 5 m/s 1 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The wheel weighs 48 lb and rests on a surface for which ?B = 0.2. A cord wrapped around it is attached to the top of the 72-lb homogeneous block. (Figure 1). If the coefficient of static friction at Dis ?D= 0.3, determine the smallest vertical force that can be applied tangentially to the wheel which will cause motion to impend. P A 1.5 ft B -1.5 ft-- C D 3 ft
The 11-lb block has a velocity of 3.83 ft/s when the force of F= (257.6t) Ib-ft/sec2 is applied. Determine the acceleration of the block whent= 2.08 s. The coefficient of kinetic friction at the surface is u 0.21. Answer is in ft/sec. F = (257.6P) Ib ft/sec? ty
В A smooth can C, having a mass of 3 kg, is lifted from Ö=2rad/s² e = 0.5 rad/s r a feed at A to a ramp at B by a rotating rod. If the rod rotates angular velocity of d=0.5 rad/s and %3D =2rad/s?, determine the forces which the rod and 600 mm circular ramp in the vertical plane exert on the can A at the instant 0-30º. Neglect the friction and the size of the can so that r = (1.2cos0) m. The ramp -600 mm- from A to B is circular, having a radius of 600 mm.
Situation 2 The 200-lb man walks up the inclined plank of negligible weight. The coefficients of static friction at A and B are 0.2 and 0.3, respecti В 20 ft |20° What is the reaction (Ib) at B?
Calculate the minimum force P required to keep the 0.294 KN rod AB from sliding. The contact surface at B is smooth, while the static friction coefficient between the rod and the wall at A is ms = 0.2 Answer = . _N A O 180 165 O 150 3 m O 175 O 160 O 155 В 170 185 - 4 m·
The roller at A is moving with a velocity of vA = 5.97 m/s and has an acceleration of a, = 2.13 m/s? when x = 3.377 m. Determine the velocity of block B at this instant. Where h = 5.33 m.
.Determine the minimum force P that will cause impending motion of the block shown in Figure P7–12. Will the block tip or slide? (If tipping occurs about point A, both the normal force N and the friction force F will be acting through point A.)
5. The 4-N weight slides with negligible friction on a horizontal table. The spring attached to the weight has a stiffness of 20 N/m and a free length of 0.5 m. When the weight is at A, its velocity is 10 m/s directed as shown. Determine the speed of the weight at B where the length of the spring is 0.8 m. Also, find the rate at which the spring is elongating at B. Horizontal table 0.8 m L 0.6 m A 4 N 10 m/s B
A packing crate of mass 40 kg is pulled by a rope as shown. The coefficient of static friction between the crate and the floor is 0.35. If a = 40°, determine (a) the magnitude of the force P required for impending motion of the crate and (b) whether sliding or tipping is impending. A 0.5 m C P af o -0.8 m B D
10. A 40-kg packing crate must be moved to the left along the floor without tipping. Knowing that the coefficient of static friction between the crate and the floor is 0.35, determine (a) the largest allowable value of a, (b) the corresponding magnitude of the force P. A 0.5 m 0.8 m
Blocks B has a mass of 20 kg and block C has a mass of 15 kg. The coefficient of static friction at the contacting surfaces is 0.2. Block A is suspended by arope that passes over a fixed cylinder and is attached to block B. The coefficient of static friction between the rope and the cylinder is 0.25. What is the largest mass block A can have without causing block B to slip the left?
The bar is smooth. The 10-kg slider at A is given a downward velocity of 5.7 m/s. What is the magnitude of the normal force the bar exerts on the slider as it passes point B? 1m C D 10 kg |A B 1 m 2 m