a) What type is the active filter shown in the following figure? b) Determine the roll-off rate. c) Find the values of the unknown resistors and capacitors to implement an equal value Butterworth response with an fc =1 KHz if the damping factor for this configuration is DF = 1.414. (Assume R2 = 1 KN) RAI CB1 R R2

Q: Q5. Figure Q5 shows an RL filter circuit. R Vin Vout Figure Q5: RL filter (a) What is the frequency…

A:

Q: Find the Vs/Vgs transfer function for the OPAMP circuit shown in the figure? Also find the…

A:

Q: A) By Cascading a first-order op RC low-pass circuit with a first-order RC high-pass circuit, one…

A: The OP-amp configuration works as unity gain Amplifier  and R5 and C4  network work as a Low…

Q: 4 The op-amp circuit shown in Figure P8.53 is used as a filter. C = 200 pF RL = 1 k2 R = 10 k2 R2 =…

A: The circuit diagram is, (a). Converting the circuit into frequency domain,

Q: An active filter needs to be designed using a non-inverting amplifier that behaves as a band pass…

A:

Q: 3) An active filter is requested preserving the frequencies upper than 10 Hz and eliminating the…

A: a & b) Since the filter will pass the frequency above the 10 Hz and block other frequency…

Q: (a) What type is the active filter shown in the following figure? (b) Determine the roll-off rate.…

A: Given, Damping factor DF=1.414 Cut-off frequency fc=15KHz Resistors R2=10KΩ, RA=10KΩ Here, we have…

Q: A sinusoidal sound (pressure) wave p(t) impingesupon a condenser microphone of sensitivity…

A: Given value of input sound wave -

Q: A first-order PLL is operating with zero frequency and phase error when a step in frequency of…

A:

Q: 5 The circuit shown in Figure P8.55 is an active filter with R = 4.7 k2 C = 100 pF R2 = 68 k2 R1 =…

A: The circuit diagram is, Determining the transfer function of the circuit,

Q: 1-With the aid of diagrams and equations, state the differences between: a. Active filters and…

A: NOTE- As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the…

Q: 7 The op-amp circult shown in Figure P8.57 is used as a filter. R = 9.1 k2 R = 22 k2 C= 0.47 µF R =…

A: Given values are = Given circuit is =

Q: a) Design a digital bandpass Butterworth filter with the following specifications: Center frequency…

A: Butter worth Band Pass filter  Realizing it by given characteristics :  fc = centre frequency…

Q: equivalent using pole-zero mapping. The filter is to be used with a sampling frequency of 4 Hz. The…

A:

Q: bessel bandpass filter analysis and all formula. lecture summary

A: Bessel bandpass filter analysis is as follows: Bessel filter is a sort of simple straight channel…

Q: Design an RLC bundpass passive filter (paralel LC) if f 5 KHz, CalpF,=IKHz, A) Draw the eircuit,…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Q6. Which of the following is a significant limitation of a passive filter compare to active filter?…

A: 6. The limitation of the passive filter as compared to active filter is that the precise tuning is…

Q: [Q3] Choose appropriate values for this Sallen-Key high-pass filter circuit to give it a cutoff…

A:

Q: Discussion: - Discuss the effect of increasing the order of the filter on the frequency response of…

A:

Q: Question 2: Write the difference between active and passive filters in detail. Question 3: What does…

A: Filter: The filters are circuits that is used to remove the unwanted portions of a frequency…

Q: [Q5] Choose appropriate values for this Sallen-Key high-pass filter circuit to give it a cutoff…

A: The Sallen–Key topology is a simple electrical filter design that is often used to create…

Q: he band-pass filter in the figure is required to pass signals with a frequency of f = 39 kHZ with a…

A: Answer for the question below

Q: Design a two-pole high-pass Butterworth active filter having a cutoff frequency at fus 25 kHz and a…

A:

Q: (b) Design a 1 order Band Pass Filter using op-amp with fuc = 18KHZ, fic = 3KHZ and pass band gain,…

A: According to the question we have to draw the circuit using standard resistance values.

Q: 5. Why we use semiology paper to draw the frequency response of filters. 6. What is filter order,…

A:

Q: A first-order PLL is operating with zero frequency and phase error when a step in frequency of…

A:

Q: CR active filters find extensive use in communications and instrumentation measurements. a) By…

A: Given CR active filter is shown below. The input impedance Zin=Rin+1sCin. Put s=j2πf ; where…

Q: Q3: Design a Low-Pass Active Filter to produce the response illustrated in Figure 2. What would you…

A:

Q: Continuous-Time Filters 33. In Figure E.33 are some descriptions of filters in the form of an…

A:

Q: The function generator circuit in the EIA has been designed to generate a sinewave output voltage…

A: Expression for triangular waveform with peak amplitude, substitute s=jw and taking modulus on both…

Q: Q2 (a) As part of a radio receiver, you are asked to design a simple bandpass filter using a series…

A:

Q: Design a low-pass active filter of cut-off frequency 100 kHz and gain 32 dB. (assume C = 0.1nF)

A:

Q: 2) Consider the active filter and corresponding transfer function shown below. R2 Transfer Function…

A:

Q: a) Design a 5th order Butterworth Low pass Filter with the cut-off frequency of 4 KHz. Use the…

A: Solution (a) - The 5th order Butterworth low pass filter is shown below, Given, R=5.6 kΩcut off…

Q: Design an active bandpass filter using a cascade connection by using a 6 μF capacitor to give a…

A:

Q: a. Design a S-tap FIR band reject filter with a lower cutoff frequency of 2,000 Hz, an upper cutofT…

A: According to question: a) The normalized cut off frequencies are calculated as…

Q: Please provide Handwritten answer.

A:

Q: )A full-wave rectified signal of 18 V peak is fed into a capacitor filter. What is the voltage…

A:

Q: 3 The op-amp circult shown in Figure P8.53 is used as a filter. C = 0.1 µF RL = 333 2 R = 1.8 k2 R2…

A: Given circuit is = Given values are =

Q: Q5\ Plot the typical frequency responses of four different filter circuits, showing signal output…

A: The expression for the impulse response for the low-pass filter is given by:

Q: A geophone is able to pick up signals in the frequency range of 20 Hz to 340Hz. Design an active…

A:

Q: a) What type is the active filter shown in the following figure? b) Determine the roll-off rate. c)…

A: The required parameters of the given low pass filter circuit can be obtained by assuming value for…

Q: What type is active filter shown

A: An active filter is a type of analog circuit that uses active components, typically an amplifier, to…

Q: Analogue Electronics II Design 2 different configurations of active band pass filter for the…

A: Given: A 2 different configurations of active bandpass filter for the frequency with a bandwidth of…

Q: An active filter is requested preserving the frequencies upper than 10 Hz and eliminating the…

A:

Q: Summarize the differences between passive filter and active filter in terms of gain, cost and…

A: The filter can be designed by using the passive and active elements. Based on the application, the…

Q: A) Draw the circuit, labeling the i/p and o/p and drive an expression for Ho B) Determine the value…

A: We are authorized to answer three sub-parts at a time, since you have not mentioned which part you…

Types of Thyristors

With four layers of alternating P- and N- materials, a thyristor is a solid-state semiconductor device. It acts as a type of bi-stable switch and it conducts when the gate receives a current trigger and continues to conduct until the voltage is reverse biased across the device or by some means until the voltage is removed. The silicon-controlled rectifier is considered synonymous with thyristors by some sources. Thyristors are defined as more complex by other sources as it contains at least four-layer of alternating N-type and P-type substrate. They find large applications in the control of electrical power supplies, electric motor speed control, and ranging of light dimmers because thyristors can control large amounts of power supplies and voltage with a small device. The circuit symbol of the thyristor is given below.