Question-1A) Write the instructions for the following scenario:Read two numbers from input ports (10,11).If the both inputs are equal jump to label (equal) in which put 15 in hexa into register B and haltthe program,Otherwise load(-3) to the accumulator, and continually increment the accumulator to reach to 2.B) Type above program on GnuSim8085 and run it three times with the input values in thefollowing table, and in each run fill line of the following table.Note: (don't forget to reset all before each run and update the input port)Port 1 Port 2 Register ARegister B| Flag sFlag z7.

Note: since Part B of the question is based on software, hence we will only solved part A for you.…

A) Write the instructions for the following scenario: - Read two numbers from input ports (10,11). If the both inputs are equal jump to label (equal) in which put 15 in hexa into register B and halt the program, Otherwise load (-3) to the accumulator, and continually increment the accumulator to reach to 2.

A) Write the instructions for the following scenario: - Read two numbers from input ports (10,11). If the both inputs are equal jump to label (equal) in which put 15 in hexa into register B and halt the program, Otherwise load (-3) to the accumulator, and continually increment the accumulator to reach to 2.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter32: Standby Power Systems

Section: Chapter Questions

Problem 7R: Briefly explain the function of a transfer switch. _____

See similar textbooks

Similar questions

Let the values are R1=622.8ohm,R2=915.95 ohm ,The error voltage is =7.9 Volt.and the initial value of output is 5.5 Volt. Vout =
Draw a diagram showing the interface between an 8-bit Analog to Digital (A/D) converter and 8051 microcontroller. Write the necessary assembly instructions to start the A/D conversion, wait for it to complete, and read the digital data after the conversion.
Q2/ A- Sum of series of 10 numbers stored at memory location 0100H:0500H and then store result in memory location [total] and also sum the number of carry if found and save it at memory location [carry] B- Draw The waveforms of 8086 minimum mode input bus cycle
An SN74AS138 output cannot (reliably)drive an SN74AC08 input when both chips have VCC=4.5 V. Why not?
Draw a 3-input AND gate using one 7408 Quad 2-input AND chip. Please draw on a 14 pin ic chip pinout and label the wires(A,B,C)
Electronics What is clocking block. If default skew is not given then when input signal sampled and output signal driven.
Signal and system plz explain every step that how do this
What is the effect of instruction CMC? O Set CF=1 Clear CF=0 If CF=1 Change to CF=0, and If CF=0 Change to CF=1. O None of them
Q) The static characteristics of the measurement instrument are act -- The linearity of the output. The relation between input and output. The nonlinearity of the output. O Not all above.
A multiplexer has 3 select lines and two enables. How many other inputs are there? How many TOTAL inputs are there? How many output/outputs are there? Draw a block diagram of this multiplexer.
19) Consider a 6-bit ADC and full scale voltage measurement range of (0-59).The Resolution will be _________. 0.30 0.06 0.92 1.00
Show Complete Solution. No Shortcuts. Thank you! Suppose if the signal is about 0 - 12v and we have to used 16-bit ADC. What will be the output voltage of the following analog voltage level. a. 1.2V b. 3 V c. 3.5 V d. 5 V e. 10 V Plot the analog signal level with digital output in binary. Show your complete solution.