ABC triangle is drawn on the thin plate in the figure when it is unloaded. AB length is parallel to the "x" axis and measured as AB=20cm. Determine: a) the final length of side BC. b) the amount of change of side AC. c) the amount of change in plate thickness. d) the final volume of the plate.

ABC triangle is drawn on the thin plate in the figure when it is unloaded. AB length is parallel to the "x" axis and measured as AB=20cm. Determine: a) the final length of side BC. b) the amount of change of side AC. c) the amount of change in plate thickness. d) the final volume of the plate.

Name: K=17 so 107 MPa strength of material question. -XA75050 cmC70%B150 MPa
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: K=17 so 107 MPa strength of material question. -XA75050 cmC70%B150 MPaE = 70 GPav= 1/340 cm1.5 cm(90+K) MPaABC triangle is drawn on the thin plate in the figure when it is unloaded. AB length isparallel to the "x" axis and measured as AB=20cm. Determ

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Similar questions

Question 3) The length L is given as L=34 m on the plate in the figure. According to this;Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)Question 3-B) Find the Y coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)
The square deforms into the position shown by the dashed lines. (Figure 1) The dimensions are S = 55 mm, S' = 60 mm, Az1 = 5 mm, and A₂ = 8 mm. Side D'B' remains horizontal. Figure 91.5 ATL Ax₂ 1 of 1
Ixo and Iyo of a quarter circle with a diameter of 50cm (Answer format: Ixo= , Iyo=)
Question 3) On the plate in the figure, the length L is given as L = 18 m . According to this; y 2L L 2L 3 L -- L Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result as m without writing units.) Response: Question 3-B) Find the Y coordinate of the geometric center of the plate . (Enter your result as m without writing units.) Response:
D. +z axis 01) Given the figure, AB=5m, BC= 8m and AG= 7m and pt 0 is origin. Determine the following: 250 N +y axis 1) What is magnitude of R and Cr in pt G? 20 kN m 1689 Ibf (Unit must be in N and kN-m) 1269 pounds 2) What is the magnitude of R and Cr in pt 0? +x axis (Unit must be in N and kN-m) G. 3) Unit Vector of R in the system. 4) Direct Cosines of Cr in pt 0.
Build the following part and report the volume in units cubed. A = 48 B = 51 R20 R10 B 30 50 2X R10 R20 Ø20 A 10 TYP DESIGN ERICS DRAWING TITLE
Show conv D +z axis 01) Given the figure, AB=5m, BC= 8m and AG= 7m and pt 0 is origin. Determine the following: 250 N B *y axis 1) What is magnitude of R and Cr in pt G? 20 kN m 1689 Ibt (Unit must be in N and kN-m) 1269 pounds 2) What is the magnitude of R and Cr in pt 0? +x axis (Unit must be in N and kN-m) 3) Unit Vector of R in the system. 4) Direct Cosines of Cr in pt 0.
Given the points A( – 5, 6, – 4), B( – 2, — 10, 6), and C'(4, 0, 5), find (a) the angle between AB and AC, (b) the angle between BA and BC, and (c) the angle between CA and CB. (a) ZBAC = 29.9 (b) ZABC 42 (c) ZACB = 95.225 Submit Question X X > 8
Q3// for this figure a=9 in, b=7 in, c=5 in ,R= 4 in find : a) The total area إجابتك Q3-b) Find the value of X- bar إجابتك Q3-c)Find the value of Y- bar
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
5. वो D 10' F is the orange arrow C 10' B 45* 1000lbs Find FAD, FBC, FCD FAB FAC -7
Frame and Machine From the figure, the load at G is 12 kN: 450 900 500, 600 1000 To determine: a) Piston force JL b) Pin force E and M c) Pin force D and C 600 M 450 600 450 D. 450 450 300 Analytical Solution. Two decimal numbers for the calculation Dimensions in millimeters 1000