Air enters an adiabatic nozzle steadily at 500 K and 500 kPa with a low velocity. and exits at a pressure of 100 kPa. Determine the maximum possible speed of the air at the exit of this nozzle. Consider constant specific heats evaluated at 300 K 595 m/s b) 556 m/s a) c) 609 m/s d) 638 m/s e) 627 m/s

Air enters an adiabatic nozzle steadily at 500 K and 500 kPa with a low velocity. and exits at a pressure of 100 kPa. Determine the maximum possible speed of the air at the exit of this nozzle. Consider constant specific heats evaluated at 300 K 595 m/s b) 556 m/s a) c) 609 m/s d) 638 m/s e) 627 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8 - Water vapor enters an adiabatic nozzle with a continuous flow at a temperature of 350ºC and a pressure of 4 MPa. What is the specific volume at the inlet? a) 0.06647 m³/kg B) 0.07343 m³/kg NS) 0.05842 m³/kg D) 0.05197 m³/kg TO) 0.05784 m³/kg
Compressor accepts ideal gas at 25 C and compresses it to 75 C. During compression stage it gives off heat in the amount of 10 kJ/kg. Determine work of the compressor? (specific heat values are c_p=1 kJ/(kg*K), c_v=0.5 kJ/(kg*K)) A)15 kJ/kg B)70 kJ/kg C)60 kJ/kg D)35 kJ/kg E)50 kJ/kg
3. A 750 liter rigid tank (1 liter = 0.001 m³) initially contains water at 250 (°C), which is 50% liquid and 50% vapor by volume. A valve at the bottom of the tank is opened and liquid is slowly drawn. Heat transfer to the tank takes place such that the temperature at exit remains constant (250 (°C)). Find the amount of heat transfer required: i) where half of the original mass of liquid water is withdrawn ii) where half of original mass is withdrawn (both liquid and vapor)
Refrigerant R-134a enters a continuous flow adiabatic compressor as saturated steam at a speed of 2 kg/s at -14 OC and is compressed to 0.8 MPa and 70 oC. If the kinetic and potential energy exchange is neglected, what is the power consumed by the compressor? a)110 kW b)130 kW c)78 kW d)94 kW (please can you help quickly)
(Open System) A garden hose attached with a nozzle is used to fill a 10 gal bucket. The inner diameter of the hose is 2cm and it reduces to 0.8 cm at the nozzle exit. If it takes 50s to fill the bucket with water, determine a) volumetric flowrate( L/s) and mass flowrate (kg/s) of the water through the hose b) average velocity of water at the nozzle exit (m/s)
The power generated by an adiabatic steam turbine is 5MW, when the steam enters the turbine at a pressure of 2.3MPa, a temperature of 400C and a speed of 50m/s; and leaves the turbine at a pressure of 15kPa, a quality of 90% and a speed of 180 m/s a) Represent the process on a P-V diagram. b) Find the mass flow rate of the steam. c) Find the exit area of the turbine.
Steam enters a turbine at a mass flow rate of 1.4 kg/s, a pressure of 700 kPa and a temperature of 400 °C. Steam comes out of the turbine at a pressure of 100 kPa and a specific volume of 1.4 m3/kg. Since the heat transfer from the turbine to the environment is 50 kW, the boundary temperature between the turbine and the environment is 70 °C,a) Find the power produced by the turbine.b) Calculate the entropy produced in the turbine.c) Find the isentropic efficiency of the turbine.Note: Changes in kinetic and potential energies will be neglected and T (K) = 273 + °C will be taken.
Consider a sealed, rigid container of 10 kg of water vapor at 25°C and 80 kpa. A paddle wheelwith a power rating of 1 kW is operated within the tank for 30 minutes. During that time 7 kJ ofheat are lost to the surroundings. a.) Define the system. b.) What types of energy transfer occur? c.) What is the net energy change of the system?
SU-1 A heat engine with &=0.400 operates between two heat reservoirs at 250K and 450K. The energy amounts and heat flow diagram for one cycle of operation of the engine is shown to the right. a) What is the change in entropy for the engine for one cycle of operation of the engine? b) Find the change in entropy for the engine surroundings for one cycle of operation of the engine. c) Find the change in entropy for the universe for one cycle of operation of the engine. d) Is this engine real, reversible, or impossible? Explain why using your results from the previous parts. Th-450K 500 200J Engne 300J T-250K
3) Consider 2 kg of air has a decrease of internal energy of 25 kJ while its temperature is reduced to one-third of the initial temperature during a reversible non flow isobaric process. Determine a) Initial temperature b) final temperature c) Heat (Q) d) Work and e) Change in Entropy
The fan diameter of a household fan heater is 0.4 m. The heater takes the air at 22°C and 95 kPa and blows it out at the same pressure, 40°C and 1.5 m/s. According to this; a) Mass flow rate of blown air (kg/s) b) The power of the heater (kW)
Steam with a pressure of 6 MPa and a temperature of 400oC is created in a boiler at a flow rate of 0.406 m3/sec and then transported through a turbine, where it forms a saturated vapour with a pressure of 60kPa. The turbine loses 61 kJ/kg of heat to the surrounding environment at 37oC. Obtain: a) The turbine's output power.b) The highest amount of energy that can be generated.c) The turbine's second law efficiency.d) The irreversibility of the process.