All of the statements below are correct exceptAThe torsional shear strain is zero at theaxis of the shaft.The torsion formula is based on therequirement that the resultant torque onthe cross-section is equal to the torqueproduced by the linear shear stressdistribution.The torsional shear strain is maximum atthe outer boundary of the shaft.The polar moment of inertia depends onthe material of the shaft.BCD If a loaded beam is cut at a certain point and the leftsection is considered, the internal forces that will beexposed areAAn upward internal shear and a clockwiseinternal momentBAn upward internal shear and acounterclockwise internal momentA downward internal shear and aclockwise internal momentA downward internal shear and acounterclockwise internal momentCD

Answered: Image /qna-images/answer/b261a7a0-19f4-499e-9acc-85720e3ff670.jpg

All of the statements below are correct except A The torsional shear strain is zero at the axis of the shaft. The torsion formula is based on the requirement that the resultant torque on the cross-section is equal to the torque produced by the linear shear stress distribution. The torsional shear strain is maximum at the outer boundary of the shaft. The polar moment of inertia depends on the material of the shaft. B C D

All of the statements below are correct except A The torsional shear strain is zero at the axis of the shaft. The torsion formula is based on the requirement that the resultant torque on the cross-section is equal to the torque produced by the linear shear stress distribution. The torsional shear strain is maximum at the outer boundary of the shaft. The polar moment of inertia depends on the material of the shaft. B C D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Which of the following is corresponds to the force acting at member AB? E 20 k 12 ft C D 12 ft 5 k B A |-5 ft--5 ft-- 14 ft- Select one: O a. 13.86 k O b. 15.40 k O c. 18.82 k O d. 17.11 k
7-1. If the wide-flange beam is subjected to a shear of V = 20 kN, determine the shear stress on the web at A. Indicate the shear stress components on a volume element located at this point. Prob. 7-1 200 mm A 20 mm B 20 mm 300 mm 200 mm 20 mm
7-1. If the wide-flange beam is subjected to a shear of V = 20 kN, determine the shear stress on the web at A. Indicate the shear-stress components on a volume element located at this point. 200 mm 20 mm B 200 mm -20 mm 300 mm 20 mm
6.82 Determine the absolute maximum shear in the beam due to the loading shown.
A vertical steel bar ABC is pin-supported at its upper end and loaded by a force P at its lower end (Fig. 2-12a). A horizontal beam BDE is pinned to the vertical bar at joint Band supported at point D. The beam carries a load P2 at end E. The upper part of the vertical bar (segment AB) has length L1 = 20.0 in. and cross-sectional area Aj = 0.25 in."; the lower part (segment BC) has length L2 = 34.8 in. and area Az = 0.15 in.² The modulus of elasticity E of the steel is 29.0 x 106 psi. The left- and right-hand parts of beam BDE have lengths a = 28 in. and b = 25 in., respectively. Calculate the vertical displacement &c at point C if the load P = 2100 lb and the load P2 = 5600 lb. (Disregard the weights of the bar and the beam.) 41 OB OD E P2 E P3 P2 P1 (b) P1 (c)
|8.00 kips Sketch a Free Body Diagram of a section of the truss that facilitates BY determination of member forces in BC, BF, and EF. 12 ft А E 4.00 kips y 9 ft 9 ft 18 ft Determine the force in member BF. A 5.00 kips (T) b 10.0 kips(C) d 10.0 kips (T) с о Determine the force in member BC. b 6.00 kips(C) d 3.00 kips (C) a 12.0 kips(C) ine the force in m a 12.0 kips(T) EF. b 3.00 kips(T) d 6.00 kips (T) с о
What is y-axis reaction at Support E (Reaction Ey) in KN? 10 kN A B C * 2m 2 m 2m 10 kN D 2 m E
5. What is the maximum value of shear in the shear diagram
The bridge truss shown carries the following uniform live load and concentrated live load. А в с A B D E 3m K. G S08m W(LL) P(LL) 15 110 Calculate the following: 8. Location of the concentrated live load from the right support in order to get maximum force on member BC. |
THE RIGID BEAM IS SUPPORTED BY A PIN AT A AND WIRES BD AND CE. IF THE LOAD P ON THE BEAM CAUSES THE END C TO BE DISPLACED 20mm DOWNWARD, DETERMINE THE NORMAL STRAIN DEVELOPED IN WIRES CE AND BD. 5m 4m 4m 3m 3m
*7-60. The built-up beam is formed by welding together the thin plates of thickness 5 mm. Determine the location of the shear center 0. -5 mm 200 mm 100 mm 100 mm 200 mm 300 mm Prob. 7-60
For the beam shown, the slope of shear force diagram is negative at the * .free end True O False O