I need the solution to this problem by an expert using the above-mentioned law. Allday - Allday 24 0/PAllday 24 0/P+ (Piran) 24 (Pew) 241Q1- the primary voltage of transformer is 6600 V and the turn ratio equal 10.6. If theprimary and secondary impedances are Z₁=1.4+j5.2, Z₂= 0.0117+J0.0465 respectively.Find the output power when the load draw 300 A at 0.8 lag p.f.ANS. 144 KWQ2- 100 KVA, (6600/330),single- phase transformer, the primary connected to supplyvoltage 100 V and the secondary side short-circuit. The transformer drawn 10 A and 436watt. calculate the voltage applied to primary winding at full load with 0.8 lag p.f to makesecondary voltage 330 V.ANS. 6734 V

Q1:Given: Primary voltage (Vp) = 6600 V.The turns ratio (N) is 10.6. The primary impedance (Z₁) is…

Answered: Allday - Allday 24 0/P Allday 24 0/P+…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Given Zo-j407 2, R₁143, R6317 52 and a 0.04, what is the magnitude of the source voltage Vs (in V rms) in the primary of the ideal transformer? Vs R₁ ww Answer: Zc Zc R₁ Use up to 2 digits after the decimal point if necessary in your answer below VL-28020 V TR
The turn ratio and type of transformer required for the circuit shown in figure, where the average value is 15.9 and the input voltage is 120v rms: reeeeeee 0.294 step up O 0.147 step down eeeeeee 0.294 step down 2:1 step down O 5:1 step down Other: R₁
For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 13.7- 0-13.7 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D. ст R 38.74 O 19.38 O 24.57 O 30.23 leeee
A multitap transformer has 100 turns on the primary, 100 turns between B and C, 1000 turns between A and D, and 600 turns between A and C. Calculate the secondary voltage between C and D if a 240V RMS source is connected to the primary. -OD -OC 1 -OB O 333V RMS O 960V RMS Ⓒ240V RMS O 507V RMS
primary of a certain transformer takes 1 a at a power factor of 0.4 when it is connected acrossa 200-v, 50-hz supply and the secondary is on open circuit. the number of turns on the primary istwice that on the secondary. a load taking 50 a at a lagging power factor of 0.8 is now connectedacross the secondary. what is now the value of primary current ?
The efficiency of a transformer at load 0.8 p.f. Lag is -- at load 0.8 p.f. Lead * equal less than more than none of these
5. A power-supply transformer has a secondary voltage if the primary is connected to a 120 V rms source? 6. Determine the peak and average power delivered to RL in figure. turns ratio of 5:1. What is the 2:1 120 V rms 220 N ell lelll
Problem: Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Neglect Rsurge- Rurpe 120 V ms 10N 100 uF 33 kn Express the numerical values up to 2 decimal places. Vr(pp) = Vpp Vdc = V lll lell
7 Given Zc-j309 , R₁ = 390 , RL = 6401 2 and a = 0.39, what is the magnitude of the source voltage Vs (in V rms) in the primary of the ideal transformer? Vs R₁ www 1:a 40 Zc Zc Answer: Use up to 2 digits after the decimal point if necessary in your answer below. Tune hor RL VL=28020 Vms
For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 14.9-0-14.9 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D, RL D2 32.63 21.07 42.14 O26.97
Q5/B: In the ideal transformer circuit shown below, determine the average power delivered the load 120/0° V rms 30+j1202 1000 turns 200 turns 20-140
For figure (1)draw and calculate the voltages waveform across each half of secondary winding and across load when 100sin2π60t applied across the primary, then find PIV.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning