An analog signal contains frequencies up to 10 kHz. The signal is sampled at 50 kHz. Design an FIR filter with the following specifications: Linear phase characteristic Transition band of 5 kHz • Minimum 50 dB attenuation at the end of the transition band Fully explain your design Calculations and explanation for filter length and corresponding window length and choice A frequency response plot for the designed filter • Impulse response h[n] for the designed filter Filter coefficients for designed h[n] • Matlab code

An analog signal contains frequencies up to 10 kHz. The signal is sampled at 50 kHz. Design an FIR filter with the following specifications: Linear phase characteristic Transition band of 5 kHz • Minimum 50 dB attenuation at the end of the transition band Fully explain your design Calculations and explanation for filter length and corresponding window length and choice A frequency response plot for the designed filter • Impulse response h[n] for the designed filter Filter coefficients for designed h[n] • Matlab code

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. A simple band-pass filter can be designed by cascading one-pole high-pass and one-pole low-pass filters. Using op- amp circuits similar to the one shown below, design band-pass filter with cutoff frequencies of 200Hz and 50 kHz and with a midband gain of 10dB. Resistor values must be no larger than 200k, but the input resistance must be as large as possible. Vic C oV₂ V₁ www OV
A low-pass filter is designed to have a roll-off factor of 40 dB/decade. The cut-off frequency is 200 Hz, and the maximum gain of the filter is 23 dB. Determine the following: a. Power in dB at the cut-off frequency. b. Power in dB at 4000 Hz. 3. Frequency that has a power of -20 dB.
1-With the aid of diagrams and equations, state the differences between: a. Active filters and passive filters. b. Low pass filters and high pass filters. C. Butterworth filters and chebyshev filters. saeed it is promisum 2- What are the limitations of Sallen-Key filter design topology. 3. What are the values of ideal 741 op-amp parameters (input impedance, output impedance, voltage gain). 4. Why we use 741 op-amps in the filter design. 5. Why we use semiology paper to draw the frequency response of filters. 6. What is filter order, and what is the effect of changing filter order on the filter response and complexity of filter. 7 Sketch the frequency response of low-pass, band-pass, high-pass, and band-reject filters.
Draw the circuit of a low pass RL filter and find the transfer function. Cutwith a frequency of 70 HzDesign a low pass RL filter. The amplitude-frequency-curve of this filter you designed.Draw in accordance with the calculated values.
What is the function of a low pass filter? Draw a diagram of a simple low-pass filter using a capacitor and a resistor.
3. Active Analog Filter Topologies You already know from our class discussions that Circuit 1 is an active analog Low-Pass Filter For each of the remaining three circuits, state whether the circuit will function as a low-pass or high-pass filter. Each of your answers must be accompanied by a brief explanation and justification incorporating the frequency dependent characteristics of the reactive circuit elements. That is you should look at the asymptotic impedance of the L and C if the input signal the frequency is very low or very high. Sketch the expected Bode plot for 20 log(Vo/Vs) as a function of log (f) labeling the corner frequencies. No equations are required! R2 R2 R2 R2 R1 R1 R1 Vs Vs o W- Vs Vs Vo Vo Vo Vo Circuit 1 Citcuit 2 Circuit 3 Circuit 4
Design an active lowpass filter with dc gain of 0.5 and corner frequency of 250Hz. Then draw the circuit diagram for this filter.
(b) Analyse and obtain the transfer function for the filter as shown in Figure Q2(b). R₁ VW HH R₂ W Figure Q2 (b)
1. In an application it is required to attenuate 0.5MHZ noise by 97%. Assume that the data is coming at much lower frequency than 0.5MHZ. Also assume that there is no need to amplify the filtered output signal.What kind of filter you would design in this application?a. Passive high pass filterb. Passive low pass filterc. Active low pass filterd. Active high pass filterQUESTION 21. In Question # 1, what is cut off frequency value you would choose to design the filter?a. 10KHZb. 15KHZc. 5KHZd. 100KHZQUESTION 31. In question # 1, what would be the filter gain (magnitude) for an input signal of 400HZ?a. 0.09b. 0.707c. 0.99d. 0QUESTION 41. In Question # 1, in designing the filer if you choose the capacitor value as 47pF, what resistor value you must use?a. 225Kb. 120Kc. 450Kd. 200
Explain why it is necessary to add capacitor in Low pass filter draw circuit diagram and explain w.r.t combination of Capacitor and RL.
6. Consider the switched-capacitor filter in the below figure. Design the circuit for a low-frequency gain of -10 and a cutoff frequency of 10 kHz. The clock frequency must be 10 times the cutoff frequency and the largest capacitance is to be 30pF. Find the required values of C₁, C2, and CF. SAL +
For a given transfer function of a bandpass filter circuit as shown in the figure For a given transfer function (Take K as 1) Find the center frequency, band-with and the gain for this bandpass filter. 2.Find the cut-off frequencies and the quality for this filter