An analog signal in the range 5V to 10V is to be converted to a digital signal with a quantization error of less than or equal to 0.391% for midtreadquantization. The quantization error is the maximum error occur after quantizing the analog signal.What is the required number of bits for this?SubmitYou have used 0 of 3 attemptsSaveVg =-5 Vwwos, R, = 20 k£NR2 = 40 k£2os, R3 = 80 k£2oS, R4 = 160 k£2What is the output voltage of the 4-bit weighted-resistor D/A in the above if the input is 0101? Assume Rp= 10KNWhat is the output v, in V?What is the maximum allowed tolerance (±percent) in the value of R so that the maximum error in the output is limited to +LSBquantized voltagevalue?SubmitYou have used 0 of 3 attemptsSaveans 123

In the first question we know that quantization error is half of the step size. With the help of…

An analog signal in the range 5V to 10V is to be converted to a digital signal with a quantization error of less than or equal to 0.391% for midtread quantization. The quantization error is the maximum error occur after quantizing the analog signal. What is the required number of bits for this? Submit You have used 0 of 3 attempts Save

An analog signal in the range 5V to 10V is to be converted to a digital signal with a quantization error of less than or equal to 0.391% for midtread quantization. The quantization error is the maximum error occur after quantizing the analog signal. What is the required number of bits for this? Submit You have used 0 of 3 attempts Save

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Perform the following conversion : A) converting (756.603)8 to hex b) converting A0F9.0EB to decimal C)(1001010)10 to gray D)(163.875)10 to binary E) 0110BCD to excess-3
Which of the following is true about quantization? a. Actual quantization error is the same all throughout the process.b. The signal to noise ratio is the same all throughout the quantization process.c. The smaller the resolution the less quantization error is introducedd. All of the choices
Complete the table below for Quantization of Analog Signal to Digital Signal. Use 3-bit for the Quantization. See the image below for reference. Sample Interval Quantization Level Code 1 2 3 4 5 6 7 8 9 10
The resolution of the ADC unit with the reference voltage value of 3V is set to 8 bits. If the voltage level applied to the ADC input is 1.67 V, what is the numerical value read? For numbers with commas, take 4 digits after commas.
Answer the following Hexadecimal to decimal conversion problem: Convert the HEX NUMBER 6891. 9964 to decimal number ( show steps in paper , scan and submit along with other answers) Decimal number =
Please try this question It's is digital signal processing question
Find the absolute and relative error of the following. a)The approximate value of e is used as 2.718. Calculate the absolute error and the relative error margin accordingly. b) P=3.1415927 and this value is given as an approximate result of p=3.1416. Calculate the absolute error and relative error margin accordingly.
Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e
Discuss the effect of changing the number of bits on the recovered analog waveform
H1. a sampling technique was used in digitally encoding analog data and 2048 distinct voltage levels were recorded. What size code is needed Explain with details and show step by step explanation
Convert the following Hex numbers to binary numbers: (a) : 2CE.6E8H
Convert the following(i) Convert decimal number 826 to Octal(ii) Convert decimal number 32 to binary(iii) Convert decimal number 797 to hexadecimal(iv) Convert hexadecimal value D2 to binary.(v) Convert (0.888)10 into an octal number