An electrical circuit is supplied by the output of a full-wave rectifier circuit. Given that the Fourier expression for this supply voltage is 50 Determine and produces an output current of 2.0113Cos(754t+1.326) +1.8634Cos(1508 +1.10715°) + 1.1111Cos(2262t +0.9273°) i. v==+25Cos754t + 12.5Cos1508t + 5.555Cos2262t +... ii. Tπ The resistance of the circuit The value of the reactive element in the circuit The Active, Reactive and Apparent powers supplied by the rectifier

An electrical circuit is supplied by the output of a full-wave rectifier circuit. Given that the Fourier expression for this supply voltage is 50 Determine and produces an output current of 2.0113Cos(754t+1.326) +1.8634Cos(1508 +1.10715°) + 1.1111Cos(2262t +0.9273°) i. v==+25Cos754t + 12.5Cos1508t + 5.555Cos2262t +... ii. Tπ The resistance of the circuit The value of the reactive element in the circuit The Active, Reactive and Apparent powers supplied by the rectifier

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Can someone please provide a step by step solution? Thank you! The full wave rectifier in the circuit below is to deliver 0.25A and 15V (peak) to a load. The ripple is to be no larger than 0.4 V peak-to-peak. The input signal is 120 V (rms) at 60 Hz. Assume V(lambda) = 0.7 V . Determine the required turns ratio, the filter capacitance, and the diode PIV rating.
Assume the input signal to a rectifier circuit has a peak value of VM = 12 V and is at a frequency of 60 Hz. Assume the output load resistance is R = 2 k and the ripple voltage is to be limited to Vr = 0.4 V. Determine the capacitance required to yield this specification for a (a) full-wave rectifier and (b) half-wave rectifier.
3. Draw a half wave and full wave rectifier circuit with 1 KQ load resistance and sketch the output waveforms when the input is 10 V sinusoidal signals. Also find the de values for both the circuits.
Determine the ripple factor for the filtered rectifier circuit below when RL= 4KQ. Then explain briefly the effect of changing in the RL value on the output waveform.
A classical rectifier is to be designed to provide 5V  1% for a logic circuit, with output power ofup to 12W. The input is conventional 220V, 50Hz source.a. Choose a transformer ratiob. Choose a diode configurationc. Calculate the capacitor value to meet the requirementsd. Draw the load voltage, the load current and the source current (secondary side)waveforms for maximum output power (12W).
A Full-wave bridge rectifier Circuit contains 4 Germanium diodes Cuse the Constant voltage drop model with VD = 0.30) driving ac a Load resistance of 10 kur. An Source with a Peak value of 4ou at bottz Vortage Source with a applied to the Circuit. a DIS 2 Determine the de value of the output wave form Determine the value of the Capacitor In uf needed to limit the output ripple vortage to 0.5 V if the Peak output voltage is equal to Upic -2VD
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
Show the downward shift of the output signal with the series capacitor and diode. Clampers or DC restorers are clamp a peak of a waveform to a specific DC level compared with a capacitively coupled signal which swings about its average DC level (usually 0V). If the diode is removed from the clamper, it defaults to a simple coupling capacitor– no clamping. What is the clamp voltage? And, which peak gets clamped? Why is this so? Produce a schematic diagram with LTspice schematic capture program. Voltage values: Capasitor value: 1000 pF DC offset: 0 V Amplitude: 5 V Freq: 1 KHz
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: a) Peak AC voltage Vm of the source b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance
A power supply of bridge rectifier system with 1-kQ load and 10 pF capactor value, is supplied by 220-V (r.m.s) and 60-Hz input voltage through a 44-to-2 step-down transformer. Assume all diodes are ideal. Draw the complete circuit, Draw the output voltage waveform across the load resistance including al necessary values, C Find the peak-to-peak value of the ripple voltage Find the output frequency value, [ Find DC Voltage value, [ Find load current value, What do you expect for ripple voltage if the capacitor value has been increased by 10 times? [ What is the minimum Zener voltage value, Vz required to stabilize the output voltage, redraw the system again including the Zener diode?
5. A single-phase full-wave bridge diode rectifier is supplied from 230 V, 50 Hz source. If the load is highly inductive with a resistance of R Vin, Vo, VD2, VD3, io and is waveforms, and then determine: (a) The average values of output voltage and output current. (b) The average and RMS values of diode current. (c) The ripple factor. = 10. Sketch