An embankment consists of clay fill for which c=25 kPa and angle of internal friction is 260 9from consolidated undrained test with pore pressure measurement) The weight of fill per unit volume is 18.64 kN/m3. Compute the stress in kPa at depth of 20 m. a. 192.8 b. 62.5 c. 21.6 d. 372.8

Q: determine the shear force and bending moment at point 1 (P1) in the figure.

A: Asked: To determine the shear and bending moment at point 1 (P1).   Let us write the shear force and…

Q: A steel column carries an axial load of 200 kN, a moment of 50 kN-m at the top and moment 25 kN-m at…

A: P = 200KN = 200 x 103 Mmax = 50KNm = 50 x 106 Nmm  1N/mm2 = 1 MPa

Q: Q.1) Determine the coordinates of the centroid of the y = area. 2 mm Answer: 4 mm

A:

Q: draw the shear and bending moment

A:

Q: see the photo attached

A:

Q: Compute the angle of resistance in degrees.

A:

Q: b) For the welded connection below, fillet weld of different lengths are provided at the heel and…

A: Solution: Given: Section: 2 L76 x 76 x 11 area = 1430 mm2 Total length of the weld = 80 + 120 = 200…

Q: (c) A horizontal curve is designed for a two-lane road in mountainous terrain. The following data…

A:

Q: 0.5 in. | 105 in. A 2 ft The A-36 steel bar shown in the figure is constrained to just fit between…

A:

Q: Consider the mechanism shown. Members AB and BC are joined by a hinge at B. End A of member AB is…

A: Option (d) is correct.

Q: 1.1 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that…

A:

Q: Find the optimal Solution of following transportation system

A: Given: Solve by using Simplex method

Q: n, determine the maximum value o (a) in link AB, (b) in link BC.

A:

Q: List all required code of practice in designing reinforced concrete structural

A: Certain codal provisions are followed for the design of reinforced structural members. Codes are…

Q: . Two tangents having azimuths of 240° ans 282° are connected by an 80-m spiral curve with a º…

A:

Q: Which of the following is true about land subsidence caused by overuse of groundwater? the land…

A: In this question some statement regarding land subsidence is asked

Q: 5. Provide the missing bearings of the following=

A: solution Given line ABForward bearing =N44°38'E the whole cicrle bearing =44°38'as we know back…

Q: A 119-degree V-notch-weir was installed to measure the flow in an artificial channel. The crest of…

A:

Q: PROBLEM 2. A simple beam loaded as shown. Determine the following: (1) reactions @support; & (2)…

A:

Q: PLACE YOUR ANSWERS HERE. Ix= ly= r₂ = Ty= 4"x6"X" 10" 12" 4"X 8"X1" X

A: rx = (Ix/A)0.5

Q: The following data are from a direct shear test on an undisturbed soil sample. Represent the data by…

A:

Q: P = 9 kip 2 in. 1 in. 1.5 ft The aluminum post shown in the figure is reinforced with a brass core.…

A:

Q: deflection by

A:

Q: The results of a standard compaction test for a soil having a value of (Gs = 2. 5) are shown in the…

A: Water Content (%) 6.2 8.1 9.8 11.5 12.3 13.2 Unit Weight (KN/m3) 16.9 18.7 19.5 20.5 20.4 20.1…

Q: A cylindrical sample of soil having a cohesion of 80 kN/m2 and an angle of internal friction of…

A:

Q: For a 2D truss with 10 nodes, only 4 nodes are supported and they are all pinned. How many Degrees…

A: Please find the answer in the below attachments

Q: 1. A circular sewer pipe 1.6 m in diameter is laid on a slope of 2 m per kilometer. The pipe is made…

A: Given data Shiva Dia is equal to 1.6 Is laid on slope of 2 m per kilometre Mannings constant is…

Q: For

A:

Q: Refer to the soil profile shown in figure below. A laboratory consolidati the results: o'c = 100 kPa…

A: Dry unit weight of sand γdsand=Gγw1+e=2.669.811+0.55=16.835kNm3Sat unit weight of sand…

Q: In the figure, the two spheres shown impinge against each other along their line of centers. If the…

A:

Q: Which of the following is false about single point movement detection in deformation analysis? It is…

A: Since it is a single point movement detection so  It is a process of identifying an unstable point…

Q: How important is lime to the performance of concrete? How does lime affects the performance of…

A: Lime provides high water retention, ensuring the fastest possible hardening of the binder. High…

Q: Evaluate * cos(x) - 1| dx.

A: | cosx-1| = (1-cos(x))

Q: As shown in the figure, where is the location of moment equal to zero from point A in lb-ft? Use 2…

A:

Q: Hwk 2-1.2: solve for bar forces using method of joints. Name: 7k 4k A 6k B 30° 4' C * X 4 E 4' G F…

A:

Q: As shown in the figure, what is the maximum negative value of shear in lb? 600 lb 900 lb D B RA 4 ft…

A:

Q: 89.5 m and the bed surface at elevation 92 to draw the downstre

A:

Q: Situation 1: The frame shown in the figure is to be analyzed using the cantilever method. 36 kN A B…

A:

Q: 1.12 The frame shown consists of four wooden members, ABC, DEF, BE, and CF. Knowing that each member…

A: To find stress in member BE ,CF

Q: QUESTION 13 F, 10 B, 14 E, 6 H, 2 A, 8 C, 10 D, 8 G, 12 For the network diagram shown above, what is…

A: The activities duration and their interrelationships are given.

Q: There are 3 strategies to solve the turbulent flows in conduits, which are as follows: Case 1 goal -…

A: given- Equations for turbulent flow in a conduit is given.…

Q: Consider the mechanism shown. Members PQ and QR are joined by a hinge at Q. End P of member PQ is…

A: Option (D) is correct

Q: 10. The hammer of a pile driver weighs 1000 lbs and must be lifted a vertical distance of 6ft in 3…

A:

Q: E 600 mm D |P 400 mm A B - 600 mm- 600 mm- If the applied force P causes the rigid arm ABC to rotate…

A:

Q: a rectangulsr suppressed weir is placed on the side of a reservoir whose plan area is a constant…

A: step 1-

Q: wooden members of un le scarf splice shown. K le stress in the glued sp ad P that can be safel ring…

A:

Q: 2.116 From a group of 4 men and 5 women, how many committees of size 3 are possible (a) with no…

A: In this given question four men and 5 women are given and we have to choose committee that consist…

Q: Find the work done value Force applied on box=10.4 N Distance covered3D2 m

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: Data and Results for Direct Shear Test: Normal Stress (kPa):  100; 200; 300 Shear Stress (kPa):…

A:

Q: layer of soft clay having an initial void ratio of 1.5 is 15 m thick. Under a compressive load…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.