An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most significant bits are used as a network ID, and the 16 least significant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?

An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most significant bits are used as a network ID, and the 16 least significant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?

Principles of Information Security (MindTap Course List)

6th Edition

ISBN:9781337102063

Author:Michael E. Whitman, Herbert J. Mattord

Publisher:Michael E. Whitman, Herbert J. Mattord

Chapter6: Security Technology: Access Controls, Firewalls, And Vpns

Section: Chapter Questions

Problem 2RQ

See similar textbooks

Similar questions

An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most signi cant bits are used as a network ID, and the 16 least signi cant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?
In IPv4, the address format is a 32-bit numeric number that is frequently written as four octets separated by periods from the range [0, 255]. At the time of writing, Internet Protocol version 6 (IPv6), with 128-bit addresses, was gradually replacing IPv4. How many IP addresses may be assigned in IPv4 and IPv6 in theory?
Which of the following instructions falls in the category of data transfer instructions? JUMP LOAD ROTATE AND
• IPV6 addresses use 128 bits to represent an address which includes bits to be used for subnetting. The second half of the address (least significant 64 bits) is always used for hosts only. Therefore, there is no compromise if we subnet the network. Use the Figure below to Create five subnets using route prefix 2001:db:acad::/48 (1 Marks) Routing Prefix Subnet ID Interface ID 48 Bits 16 Bits 64 Bits
Computer Science What is the total number of addresses in IPv6 address scheme (give your answer in comma separated actual numeric value)? Give examples of IPv6 address types: a unicast address, a multicast address, a loopback address, and an unspecified address (e.g., when host does not have an address assigned).
TCP session sends 50 packets per second over an Ethernet Local Area Network (LAN). Each packet consists 2280B (excluding the preamble and cyclic redundancy check (CRC)). Calculate the size of the headers, and hence the TCP payload data. What therefore is the TCP throughput of the session?
IP datagrams on a specific network can carry a maximum of only 440 bytes in the data portion. A node on this network, running an application using TCP generates a TCP segment with 1,900 bytes in the data portion. How many IP packets are transmitted to carry this TCP segment, and what are their sizes (including the header of 20 bytes)?
Registration Number: 193046 Consider a network with 3 hosts and a NAT router. Suppose that the network address of the home network is 192.168.NNN/24, where NNN are the last 3 digits of your Reg#. For example, if your Reg# is BSE193046, NNN = 046 and therefore the network address wil be 192168.46/24. (If NNN>255, consider NNN=254) (a) Assign any public IP address to NAT router’s outgoing interface. (b) Assign IP addresses to all 3 hosts and local interface of the NAT router in the home network. (
To begin, what is an IP address and how does it work? Is there a reason to use mnemonic addresses? How many domains can be represented in a 32-bit representation? Exists a limit to the size of a domain in terms of the number of computers it can hold?
TCP / IP uses the client-server communication model, in which a user or computer (a client) receives a service (such as sending a web page) from another computer (a server) on the network. In short, the TCP / IP protocol suite is classified as stateless, which means that each client request is considered new because it has nothing to do with previous requests. Being stateless, network routes are released so that they can be used continuously. Answer the following questions briefly. How does resource reservation work in the TCP / IP model? Which TCP / IP layer is responsible to reserve resources across a network using the TCP / IP model? What protocol assigns an IP address to the client connected to the Internet? Checksum is used by various protocols on the Internet, but not at the one of TCP / IP Explain.
You are hired to design and manage a network of a company. The topology of the network is shown above. The Internet Service Provider (ISP) provides the following information to connect the corporate network to the Internet. The CIDR range given for the company: 124.34.52.0/21 The address of the ISP router (also called "Gateway address"): 124.34.63.254 Configure the network by giving CIDR blocks for each company subnet and IP addresses for each station and router knowing that: For Ethernet 1, we need 514 hosts to connect. For Ethernet 2 we need 50 hosts to connect. For Ethernet 3 we need 123 hosts to connect. For the Token Ring network we need 132 hosts to connect. You need to take into account the gateway addresses that need to be allocated for each of the subnets. Assign IP addresses to hosts A, B, C and D and IP addresses to the router gateway interfaces. DON'T FORGET TO FILL-IN THE BLANKS BELOW. Computer B Internet Ethernet 1 Computer C Computer A Ethernet 2 Router 1 Token Ring 1…
A 3200 bit long TCP message is transmitted to the IP layer and becomes a datagram after adding a 160 bit header. The following Internet is connected by two LANs through routers. But the data part of the longest data frame that the second LAN can transmit is only 1200 bits. Therefore, datagrams must be segmented in the router. How many bits of data does the second LAN transmit to its upper layer?