An oil pump is drawing 40 kW of electric power while pumping oil with p = 860 kg/m³ at a rate of 0.1 m³/s. The inlet and outlet diameters of the pipe are 8 cm and 12 cm, respectively. If the pressure rise of oil in the pump is measured to be 250kPa and the motor efficiency is 90 percent, determine the mechanical efficiency of the pump. 33.53 O 31.53 32.8 34.7 12 cm 14 Oil AP=250 kPa AP=2 0.1m³/s Pump 8 cm 40 kW کے Motor

An oil pump is drawing 40 kW of electric power while pumping oil with p = 860 kg/m³ at a rate of 0.1 m³/s. The inlet and outlet diameters of the pipe are 8 cm and 12 cm, respectively. If the pressure rise of oil in the pump is measured to be 250kPa and the motor efficiency is 90 percent, determine the mechanical efficiency of the pump. 33.53 O 31.53 32.8 34.7 12 cm 14 Oil AP=250 kPa AP=2 0.1m³/s Pump 8 cm 40 kW کے Motor

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q6) An oil pump is drawing (25 kW) of electric power while pumping oil with (= 860 kg/m3) at a rate of (0.1 m3 /s). The inlet and outlet diameters of the pipe are ( 8 cm and 12 cm), respectively. If the pressure rise of oil in the pump is measured to be (250 kPa) and the motor efficiency is (90 percent), determine the mechanical efficiency of the pump. Pump 8 cm 124 +4 al 0.1 m/s AP=250 kPa 25 kW Motor
In rural housing the water source is obtained through groundwater pumped upwards. Suppose the groundwater source has a depth of 60 m from the surface. The water will be lifted as far as 5 m above ground level with a pump. The diameter of the pipe inlet is 10 cm and the outlet is 15 cm.By ignoring the interaction of heat with the environment and heat due to friction, determine the input work (Watt) required by the pump for the water to flow stable at a rate of 15 liters / s. (Water type mass 1000 kg / m ^ 3). (Application of the 1st Law of Thermodynamics to open systems)
The capacity of a certain pump is 5251 gallons per hour with a capacity of 68.54%. A city uses this pump to extract water from a water supply from a body of water where in the intake is 10.2 ft below the surface of the body of water. A 3-in S40 is used to transfer the water through a pipe with a total length of 8848 ft having a total friction loss of 222.7 (ft-lbf)/lbm. Given that the cost electrical power is 14.7 cents/kWh, what is the hourly pumping cost in cents per hour? Note that in this problem, the inlet to the pump is 35.7 ft above the surface of the body of water while the water level in the tank discharge is always 380 ft above the pump discharge Answer options: 700 557 1175 685 226
A centrifugal pump driven by a 120-kW motor rotating at 2400 rpm is used to pump 20°C water in a manufacturing plant. The pump operates against a head of 30 m and has an efficiency of 70%. If this pump is used against a head of 60 m, how much water (in m3/s) can the pump circulate? Select one: O a. 0.51 O b. 0.31 O c. 0.21 O d. 0.41
A centrifugal pump compresses 3 000 L/min of water from 98 kPaa to 320 kPaa. The inlet and outlet temperatures are 25 C. The inlet and discharge piping are on the same level, but the diameter of the inlet piping is 15 cm, whereas that of the discharge piping is 10 cm. Determine the pump power in W. Let the density of water be 1 000 kg/m3. (whole number)
A pump extracted water 60 meters below the ground and discharge to a tank 5 meters above the ground. Suction pipe is 10 cm in diameter while discharge pipe has 15 cm diameter. Pump efficiency is 85%and discharge 15 liters/second of water. Calculate the required motor horsepower to drive the pump.
A pump is to deliver 80 GPM of water at a density of 61.38 lb/ft 3 with a discharge pressure of 150 psig. Suction pressure indicates a 2" Hg vacuum. The diameter of the suction and discharge are 5 in and 4 in, respectively. The pump had an efficiency of 70% while the motor efficiency is 80%. 1. Determine the water horsepower of the pump 2. Determine the brake horsepower of the pump 3. Determine the power input to drive the motor 4. Determine the combined motor-pump efficiency
Storage tank 20 m Pump Water is pumped from a lake to a storage tank 20 m above at a rate of 100 L/s while consuming 25 kW of electric power. Disregarding any frictional losses in the pipes and any changes in kinetic energy. Determine the overall efficlency of the pump-motor unit Select one: O a 77.74 % Ob 78.48 % Oc.85.78 36 O0.9233 %
A hydraulic turbine has 50 m head available at a flow rate of 1.30 m^3/s, and its overall turbine generator efficiency is 78 %. Determine the electric power output of this turbine in kW a.237 b.589 c.378 d.497
Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of useful mechanical power to the water. The free surface of the upper reservoir is 40+0 m higher than the surface of the lower reservoir. The flow rate of water is measured as 0.03 m3/s. (a) Draw EGL and HGL for the complete system b) Draw mechanical energy flow chart for the system
A certain 15-Kw pump running at 1600 rpm has an inlet diameter of 20cm and the discharge line is 12 cm in diameter. The output from th pump is 2800 liters/min of 20C and the centerline of the pump discharge is 1.5 meter above the centerline of the intake pipe. Determine the efficiency of pump. Please show complete solutions and formulas used. Show schematic diagram too.
Water pump operates under steady flow conditions delivers 1,900 kg/min of water from an initial pressure of 82,700 Pa to a final 274,000 Pa. The diameter of the inlet pipe to the pump is 13.24 cm and the diameter of the discharge pipe is 8.50 cm. what is the work