As shown in the figure a planetary gear train consist of the arm C coupled to two gears A and B with 40 and 60 teeth respectively. If the arm rotates at 150 rpm in the anticlockwise direction about the center of the fixed gear A. Calculate the speed of gear B. How fast will gear B move if the gear A makes 300 rpm in the clockwise direction instead of being fixed. (must use Tabular method) B Arm C

As shown in the figure a planetary gear train consist of the arm C coupled to two gears A and B with 40 and 60 teeth respectively. If the arm rotates at 150 rpm in the anticlockwise direction about the center of the fixed gear A. Calculate the speed of gear B. How fast will gear B move if the gear A makes 300 rpm in the clockwise direction instead of being fixed. (must use Tabular method) B Arm C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two mating involute spur gear of 20° pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of the teeth is 12 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length, find : a. The addendum for pinion and gear wheel; b. The length of the arc of contact; c. The maximum velocity of sliding during approach and recess. Assume pinion to be the driver.
An epicyclic gear train is shown schematically in the adjacent figure. The sun gear 2 on the input shaft is a 20 teeth external gear. The planet gear 3 is a 40 teeth external gear. The ring gear 5 is a 100 teeth internal gear. The ring gear 5 is fixed and the gear 2 is rotating at 60 rpm ccw(ccw-counterclockwise and cw- clockwise) 3 2 The arm 4 attached to the output shaft will rotate at
Input shaft of the gear train shown below rotates at 1,500 RPM. The output shaft must rotate exactly at 100 RPM. Minimum number of teeth can not be less than 20 and the maximum numbor of teeth can not be more than 150. The speed of goar B must be exactly 500 RPM. Determine tho speed of gear C: Note: This is a short answer type question with limited space for answer. Therefore, write the answors and do not show any other details. Input pinion A N= 20 teeth W,= 1,500 rpm No B
The lath machine in the ( mechanical workshop uses epicyclic gear train snuwn in Figure 1 to operate. Plate gear C of this gear system are carri on the arm A and free to rotated. the pitch circle diameter of the internally toothed ring gear D is to be 214 mm and the module 4 mm. When the ring gear D is stationary, the arm A, which carries three planet wheels C of equal size, is to make one revolution in the same direction as the sun wheel B for every five revolutions of the driving spindle carrying the sunwheel B. Ring gear D Planet gear C Sun gear B Figure 1: An picyclic gear train of the lath machine Determine suitable number of teeth for all the wheels and the exact diameter of pitch circle of the ring. Calculate the number of teeth of the ring gear D.
An epicyclic gear shown in Figure 1 consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear. Sun gear Arm - Ring gear (fixed) Planet gear
Figure 1 shows a stage 1 to stage 2 compound gear train through from Gears A, B, C to D. If the input shaft rotates at 650 revolutions per minute (rpm), calculate the angular velocity (ω) in rad/s at the output shaft of the compound gear train. See below for the number of teeth for Gears A, B, C & D. Gear A: 22 TeethGear B: 48 TeethGear C: 30 TeethGear D: 70 Teeth
An indexing mechanism of the milling machine uses a gear train shown in figure task 1d. The drive is from gear wheels A and B to the bevel gear wheel D. The following table shows the tooth number on each gear, solve using tabular method. How many revolutions does D makes for one revolution of A under the following situations: Tabular column (i) If A and B are having the same speed and same direction (ii) If A and B are having the same speed and opposite direction (iii) If A is making 80 rpm and B is at rest (iv) If A is making 80 rpm and B 40 rpm in the same direction. (v) Also define the term Speed ratio and train value
An indexing mechanism of the milling machine uses a gear train shown in figure task 1d. The drive is from gear wheels A and B to the bevel gear wheel D. The following table shows the tooth number on each gear, solve using tabular method. How many revolutions does D makes for one revolution of A under the following situations: Tabular column (i) If A and B are having the same speed and same direction (ii) If A and B are having the same speed and opposite direction (iii) If A is making 80 rpm and B is at rest (iv) If A is making 80 rpm and B 40 rpm in the same direction. (v) Also define the term Speed ratio and train value Please with clear words
Q2/ Two mating involute spur gears of 20* pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on cach wheel is such that the path of approach and the path of recess on cach side are half the maximum possible length each, find: i) the addendum for pinion and gear wheel, ii) the length of arc of contact, iii)the maximum velocity of sliding during approach and recess. Assume pinion to be driver.
A compound epicyclic gear is shown in Figure Q2 Sun wheels S, and S2 are integral with the input shaft B and the annular wheel Cis fixed The planet wheel F rotates about a pın carried by the annulus C and the planet wheel E rotates about a pin attached to the arm keyed to the shaft A The numbers of teeth are shown in the figure Determine the speed of shaft A when shaft B rotates clockwise at 100 r/min D C-80 D=80 S-30 S-20 A S, S, B FIGURE Q2
A commercial quadrotor drone for the photography industry uses a propellersystem that uses gears. The 20-tooth spur pinion with a diametrical pitch of8 rotates 2000 rpm and drives a spur gear that rotates the blades. Determinethe theoretical centre distance, the number of teeth on the gear and circularpitch.
3. For the following planetry gear train determine the following 4 Sun gear: N2 = 24 teeth, Internal gear connected to drive shaft, 42T Input to Sun gear: w2 = 100 rpm ccw Input to Planet gears: W4 = 240 rpm cw Ring gear: N5 = 52 teeth. 2 a. Determine the planet gear teeth (N4) such that the carrier ouput is w arm = 120 rpm cw. b. Determine the angular velocity of the ring gear ws (units and direction). Planet pinions, 127 Planet carrier connected to transmission Figure not to scale.