At the instant shown, the 50-1lb bar rotates clockwise at 2 rad/s. The spring attached to its end always remains vertical due to the roller guide at C. If the spring has an unstretched length of 2 ft and a stiffness of k = 6 lb/ft, determine the angular velocity of the bar the instant it has rotated 30° clockwise.

At the instant shown, the 50-1lb bar rotates clockwise at 2 rad/s. The spring attached to its end always remains vertical due to the roller guide at C. If the spring has an unstretched length of 2 ft and a stiffness of k = 6 lb/ft, determine the angular velocity of the bar the instant it has rotated 30° clockwise.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cyclist pedals constantly at 7.9587 rad/s the wheels are 336.5mm in radius. If the chain is directly connected with the sprockets which are 76 mm in radius (front sprocket) and 35mm in radius (rear sprockets), Determine the angular speed of the wheel in rad/s.
The rod AB has a mass of 36 kg and a length of 1.9m. The spring is unstretched when 0- 45°. The spring constant k is 226 N/m. B Find the angular velocity of rod AB at 0 - 0. if the rod is released from rest when 0. 45°. Give your answer with 2 decimals.
The disks roll on the plane surface without slippage. The left disk rotates at 2 rad/s in the clockwise direction. Determine the angular velocity of the bar. Enter an answer in radians per second up to the second decimal place. Note that the counterclockwise direction is the positive rotation. 2 rad/s 3 ft 1 ft 1 ft
The 213-kg wheel has a radius of gyration about its center O of ko = 240 mm, and radius r = 0.4 m. When the wheel is subjected to the constant couple moment M = 85 N·m, it starts rolling from rest. Determine the wheel's angular velocity W (in rad/s) after 4.4 seconds if the wheel has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². M Your Answer: Answer
The collar A is pinned on the 4-inch bar AO₂ and slides on the pivoted arm BO₁. When the angle shown in the figure is = 45°, the bar AO₂ has a constant clockwise angular velocity of 2 rad/sec. Calculate the magnitude of the angular velocity of the bar BO₁ at that instant. Present your answer in rad/sec using 3 significant figures. -b=8" r=4" B 2 rad/sec 0₂
The telephone-cable reel rolls without slipping on the horizontal surface. If point A on the cable has a velocity VA = 0.70 m/s to the right, compute the velocity of the center O (positive if to the right, negative if to the left) and the angular velocity w (positive if counterclockwise, negative if clockwise) of the reel. 1.72 m A Answers: Vo = W= 0.60 m 1.075 i 1.25 m/s rad/s
The telephone-cable reel rolls without slipping on the horizontal surface. If point A on the cable has a velocity VÀ = 0.84 m/s to the right, compute the velocity of the center O (positive if to the right, negative if to the left) and the angular velocity w (positive if counterclockwise, negative if clockwise) of the reel. Answers: Vo = W = 1.91 m 4 0.69 m 1.315 i 1.376 Ho m/s VA rad/s
Bar AB is pinned to the fixed support at A, and the collar B is pinned to the bar at its opposite end. The bar CD can slide freely through the collar at B. At the instant shown, bar AB is horizontal, /= 1.2 m, s = 1.07 m, 0 = 60°, and wAB= 40 rad/s. If ªäß = 21 rad/s² at the instant shown, determine the angular velocity and angular acceleration of the bar CD. WAB αAB с. B The angular velocity of the bar CD is The angular acceleration of the bar CD is k rad/s. k rad/s².
3. The two sliders at B move freely on OA and the curved rail and are pin connected so they move together as one. The curved rail is described by the equation r = 200 (2- cos ) mm. If the speed of the collar is 400 mm/s when = 160°, what is the angular velocity 0 of the rod OA at this instant? ė A r 600 mm 6 rad/s 0. 400 mm 200 mm
Block E is fixed to a rope wrapped around pulley B, with pulley B fixed to wheel A. Wheel A rotates against wheel C without slipping. Block D is fixed to a rope wrapped around wheel C. Assume that the respective ropes do no not slip on the pulley and wheel.At the instant shown, wheel C has a clockwise angular speed of ω0 = 2.3 rad/s and has a clockwise angular acceleration of αC = 19.7t2 rad/s2, where t is in seconds. Determine the speed (in m/s) of Block E at the instant when t = 1.1 seconds. Take: rA = 0.88 m; rB = 0.2 m; rC = 0.6 m. Choose from the following options: a) 1.505 b) 1.192 c) 2.208 d) 3.889 e) 3.269
Determine the angular velocity (positive if counterclockwise, negative if clockwise) of link BC for the instant indicated. In case (a), the center O of the disk is a fixed pivot, while in case (b), the disk rolls without slipping on the horizontal surface. In both cases, the disk has clockwise angular velocity w = 1.9 rad/s. Neglect the small distance of pin A from the edge of the disk. The radius r = 690 mm. C r A 2r A 2r (a) (b) B r B
The disk rotates with the angular motion shown. Determine the angular velocity and angular acceleration of the slotted link AC at this instant. The peg at B is fixed to the disk. w = 6 rad/s a = 10 rad/s² A 30° 0.3 m 0.75 m 30° B